Body repairs – exterior · VW Polo V
Tightening torques
Every tightening torque the Body repairs – exterior manual gives for the VW Polo V, by repair group and procedure. Each one links to its drawing or table in the procedure.
- 191 torques
- 86 procedures
50 – Body – front
Assembly overview – lock carrier
| Item | Part | Torque | Notes |
|---|---|---|---|
| 2 | Bolt | 2.0 Nm | Qty. 2 |
| 4 | Bolt | 8.0 Nm | Qty. 3 on each side |
| 7 | Bolt | 8.0 Nm | Qty. 4 on each side |
| 10 | Bolt | 8.0 Nm | Qty. 2 on each side |
| 12 | Bolt | 30 Nm | Qty. 3 on each side |
Assembly overview – wing
All items:Specified torque
| Item | Part | Torque | Notes |
|---|---|---|---|
| 2 | Bolt | 6 Nm | Qty. 1, A-pillar. · Qty. 1, side member · Qty. 1, wheel housing · Qty. 1, wing brace · Qty. 3, wing connection piece |
| 10 | Bolt | 6 Nm | Qty. 2 |
Removing and installing wing
In the steps
| Step | Torque |
|---|---|
| Specified torque for bolts -2-: 6 Nm. | 6 Nm |
Removing and installing wing bracket
In the steps
| Step | Torque |
|---|---|
| Specified torque for bolts -3 and 4-: 6 Nm. | 6 Nm |
Assembly overview – plenum chamber bulkhead
| Item | Part | Torque | Notes |
|---|---|---|---|
| 2 | Bolt | 25 Nm | Qty. 10 · Specified torque |
Assembly overview – plenum chamber bulkhead
| Item | Part | Torque | Notes |
|---|---|---|---|
| 2 | Bolt | 8 Nm | Qty. 8 or 10, depending on the type · Specified torque |
55 – Bonnet, rear lid
Assembly overview – bonnet
| Item | Part | Torque | Notes |
|---|---|---|---|
| 7 | Hexagon nut | 20 Nm | Qty. 2 on each side for securing bonnet. · Qty. 2 on each side for securing hinge. · Specified torque |
Assembly overview – bonnet release lever
| Item | Part | Torque | Notes |
|---|---|---|---|
| 5 | Bolt | 2 Nm | Specified torque · Qty. 2 |
Removing and installing bonnet
In the steps
| Step | Torque |
|---|---|
| Specified torque for hexagon nuts -3-: 20 Nm. | 20 Nm |
Adjusting lid lock
In the steps
| Step | Torque |
|---|---|
| Specified torque for bolts -2-: 12 Nm | 12 Nm |
Adjusting striker pin
In the steps
| Step | Torque |
|---|---|
| Specified torque of bolts -2-: 10 Nm. | 10 Nm |
Removing and installing bonnet lock
1.8.1 Removing and installing lid lock, LHD vehicleTo the steps →
1.8.2 Removing and installing lid lock, RHD vehicleTo the steps →
| Step | Torque |
|---|---|
| Specified torque for bolts -5-: 12 Nm. | 12 Nm |
Removing and installing striker pin
In the steps
| Step | Torque |
|---|---|
| Specified torque of bolts -3-: 10 Nm. | 10 Nm |
Removing and installing hinges
In the steps
| Step | Torque |
|---|---|
| Specified torque for bolts -2-: 20 Nm. | 20 Nm |
Assembly overview – hinges
All items:Specified torque
| Item | Part | Torque | Notes |
|---|---|---|---|
| 2 | Bolt | 10 Nm | Qty. 2 for each hinge |
| 4 | Hexagon nut | 24 Nm | Qty. 2 |
Assembly overview – gas strut
| Item | Part | Torque | Notes |
|---|---|---|---|
| 4 | Bolt | 8 Nm +90° | Qty. 2 |
| 5 | Ball-head pin | 20 Nm +45° |
Removing and installing rear lid
In the steps
| Step | Torque |
|---|---|
| Specified torque for bolts -3-: 10 Nm. | 10 Nm |
Adjusting rear lid
In the steps
| Step | Torque |
|---|---|
| Specified torque for bolt -3-: 10 Nm. | 10 Nm |
Adjusting striker pin
In the steps
| Step | Torque |
|---|---|
| Specified torque for bolts -1-: 18 Nm. | 18 Nm |
Removing and installing bonnet lock
In the steps
| Step | Torque |
|---|---|
| Specified torque for bolts -2-: 23 Nm. | 23 Nm |
Removing and installing operating mechanism
In the steps
| Step | Torque |
|---|---|
| Tighten bolts firmly. Specified torque of bolts -4-: 4 Nm. | 4 Nm |
Removing and installing hinges
In the steps
| Step | Torque |
|---|---|
| Specified torque for nuts -4-: 24 Nm. | 24 Nm |
Removing and installing striker pin
In the steps
| Step | Torque |
|---|---|
| Specified torque for bolts -2-: 18 Nm. | 18 Nm |
Removing and installing gas strut
In the steps
| Step | Torque |
|---|---|
| Specified torque for ball head pins -4-: 20 Nm + 90° | 20 Nm + 90° |
| Specified torque for bolts on ball-head pin retaining bracket: 10 Nm. | 10 Nm |
Tank flap unit
3.1 Assembly overview - tank flap unitTo the drawing →
| Item | Part | Torque | Notes |
|---|---|---|---|
| 2 | Bolt | 1.5 Nm | Specified torque |
3.2 Removing and installing tank flap unitTo the steps →
| Step | Torque |
|---|---|
| Specified torque for bolt -2-: 1.5 Nm | 1.5 Nm |
57 – Front doors, door components, central locking
Assembly overview – door
| Item | Part | Torque | Notes |
|---|---|---|---|
| 2 | Multi-point socket head bolt | 32 Nm | Always renew bolts after loosening. |
| 4 | Bolt | 23 Nm | This bolt must be removed from hinge to remove door |
| 5 | Multi-point socket head bolt | 32 Nm | Installed from inside vehicle. · Always renew bolts after loosening |
| 7 | Multi-point socket head bolt | 32 Nm | Always renew bolts after loosening |
| 8 | Bolt | 30 Nm | Unscrew and remove this bolt to remove the door. |
| 10 | Bolt | 9 Nm | Qty. 2 · For door arrester |
| 13 | Multi-point socket head bolt | 32 Nm | Always renew bolts after loosening |
| 14 | Multi-point socket head bolt | 32 Nm | Always renew bolts after loosening. |
| 16 | Bolt | 23 Nm | This bolt must be removed to remove door from hinge pin. |
In the steps
| Step | Torque |
|---|---|
| To loosen or tighten bolt, remove or install glove compartment on front passenger side ⇒ General body repairs, interior; Rep. gr. 68; Compartments/covers; Removing and installing glove compartment. | 32 Nm |
Removing and installing door
In the steps
| Step | Torque |
|---|---|
| Specified torque for bolts -7-: 23 Nm. | 23 Nm |
| Specified torque for bolts -5-: 30 Nm. | 30 Nm |
Installing after renewing A-pillar
In the steps
| Step | Torque |
|---|---|
| Insert door and tighten bolts -2, 5, 7 and 8- to 20 Nm and at 90°. | 20 Nm |
Adjusting striker pin
In the steps
| Step | Torque |
|---|---|
| Specified torque for bolts -2-: 20 Nm. | 20 Nm |
Removing and installing door arrester
In the steps
| Step | Torque |
|---|---|
| Tighten bolts -3-, specified torque: 9 Nm. | 9 Nm |
| Tighten bolt -4-, specified torque: 30 Nm. | 30 Nm |
Assembly overview – door components
2.1.1 Assembly overview – door components, 2-door modelTo the drawing →
| Item | Part | Torque | Notes |
|---|---|---|---|
| 10 | Bolt | 18 Nm | Qty. 2 · Specified torque |
2.1.2 Assembly overview – door components, 4-door modelTo the drawing →
| Item | Part | Torque | Notes |
|---|---|---|---|
| 12 | Bolt | 18 Nm | Qty. 2 · Specified torque |
Assembly overview – door handle and door lock
All items:Specified torque
| Item | Part | Torque | Notes |
|---|---|---|---|
| 2 | Bolt | 3.5 Nm | For lock cylinder. |
| 8 | Bolt | 1.5 Nm | Mounting bracket is loosened from door when this bolt is loosened. |
| 11 | Bolt | 20 Nm | Qty. 2 |
Removing and installing window regulator motor
In the steps
| Step | Torque |
|---|---|
| Specified torque for bolts -2-: 3 Nm | 3 Nm |
Removing and installing window regulator
In the steps
| Step | Torque |
|---|---|
| Insert thread of window regulator through door -arrow c- and tighten hexagon nuts -4-; specified torque: 8 Nm. | 8 Nm |
Removing and installing striker pin
In the steps
| Step | Torque |
|---|---|
| Position striker pin -1- on pillar -3- and tighten bolts -2-; specified torque: 20 Nm. | 20 Nm |
Removing and installing lock cylinder
In the steps
| Step | Torque |
|---|---|
| Specified torque for bolts -5 and 7-: 3.5 Nm. | 3.5 Nm |
Removing and installing door handle bracket
In the steps
| Step | Torque |
|---|---|
| Tighten bolt -2-, specified torque: 1.5 Nm. | 1.5 Nm |
Removing and installing door lock
In the steps
| Step | Torque |
|---|---|
| Specified torque of bolts -2-: 20 Nm. | 20 Nm |
58 – Rear doors, door components
Assembly overview – door
| Item | Part | Torque | Notes |
|---|---|---|---|
| 2 | Multi-point socket head bolt | 32 Nm | Always renew bolts after loosening. |
| 4 | Bolt | 23 Nm | This bolt must be removed from hinge to remove door |
| 5 | Multi-point socket head bolt | 32 Nm | Installed from inside vehicle. · Always renew bolts after loosening |
| 7 | Multi-point socket head bolt | 32 Nm | Always renew bolts after loosening |
| 8 | Bolt | 30 Nm | Unscrew and remove this bolt to remove the door. |
| 10 | Bolt | 9 Nm | Qty. 2 · For door arrester |
| 13 | Multi-point socket head bolt | 32 Nm | Always renew bolts after loosening |
| 14 | Multi-point socket head bolt | 32 Nm | Always renew bolts after loosening. |
| 16 | Bolt | 23 Nm | This bolt must be removed to remove door from hinge pin. |
In the steps
| Step | Torque |
|---|---|
| Remove B-pillar trim ⇒ General body repairs, interior; Rep. gr. 70; Trims, interior; Removing and installing B-pillar trim. | 32 Nm |
Removing and installing door
In the steps
| Step | Torque |
|---|---|
| Specified torque for bolts -7-: 23 Nm. | 23 Nm |
| Specified torque for bolts -5-: 30 Nm. | 30 Nm |
Installing after renewing B-pillar
In the steps
| Step | Torque |
|---|---|
| Insert door and tighten bolts -2, 5, 7 and 8- to 20 Nm and at 90°. | 20 Nm |
Adjusting striker pin
In the steps
| Step | Torque |
|---|---|
| Specified torque for bolts -2-: 20 Nm. | 20 Nm |
Removing and installing door arrester
In the steps
| Step | Torque |
|---|---|
| Tighten bolts -3-, specified torque: 9 Nm. | 9 Nm |
| Tighten bolt -4-, specified torque: 30 Nm. | 30 Nm |
Assembly overview – door components
| Item | Part | Torque | Notes |
|---|---|---|---|
| 8 | Bolt | 18 Nm | Qty. 2 · Specified torque |
Assembly overview – door handle and door lock
All items:Specified torque
| Item | Part | Torque | Notes |
|---|---|---|---|
| 5 | Bolt | 1 Nm | Mounting bracket is loosened from door when this bolt is loosened. |
| 10 | Bolt | 18 Nm | Qty. 2 |
Removing and installing window regulator motor
In the steps
| Step | Torque |
|---|---|
| Specified torque for bolts -2-: 3 Nm | 3 Nm |
Removing and installing window crank mechanism
In the steps
| Step | Torque |
|---|---|
| Specified torque for bolts -2-: 3 Nm | 3 Nm |
Removing and installing window regulator
In the steps
| Step | Torque |
|---|---|
| Insert thread of window regulator through door and tighten hexagon nuts -2-; specified torque: 8 Nm. | 8 Nm |
Removing and installing striker pin
In the steps
| Step | Torque |
|---|---|
| Position striker pin -1- on pillar and tighten bolts -2-, tightening torque: 20 Nm. | 20 Nm |
Removing and installing door handle bracket
In the steps
| Step | Torque |
|---|---|
| Tighten bolt -4-, specified torque: 1 Nm. | 1 Nm |
Removing and installing door lock
In the steps
| Step | Torque |
|---|---|
| Specified torque of bolts -4-: 18 Nm. | 18 Nm |
60 – Sunroof
Assembly overview – sliding sunroof
| Item | Part | Torque | Notes |
|---|---|---|---|
| 2 | Bolt | 5.5 Nm | Bolts are microencapsulated and must always be renewed after loosening. · Qty. 6 |
| 6 | Bolt | 2.5 Nm | For the cover · Qty. 3 |
| 8 | Bolt | 4 Nm | For sliding sunroof motor. · Qty. 3 |
| 11 | Bolt | 3 Nm | Bolts are microencapsulated and must always be renewed after loosening. · Qty. 13 |
| 14 | Bolt | 2 Nm | For wind deflector. · Qty. 2 |
Assembly overview – sunroof roller blind
All items:Qty. 2 · Specified torque
| Item | Part | Torque | Notes |
|---|---|---|---|
| 3 | Bolt | 2.5 Nm | For sun blind |
| 11 | Bolt | 1 Nm | For the handle |
Removing and installing wind deflector
In the steps
| Step | Torque |
|---|---|
| Insert and tighten bolts -4- on left and right, specified torque: 1.5 Nm. | 1.5 Nm |
Removing and installing glass panel
In the steps
| Step | Torque |
|---|---|
| Torque wrench 210 Nm - V.A.G 1783- | 210 Nm |
| After adjusting panel height, tighten securing screws -5- (5.5 Nm). | 5.5 Nm |
Adjusting glass panel
In the steps
| Step | Torque |
|---|---|
| Tighten the front inside bolts (5.5 Nm). | 5.5 Nm |
| Tighten the rear inside bolts (5.5 Nm). | 5.5 Nm |
| Open glass panel and tighten the rear bolts (5.5 Nm). | 5.5 Nm |
Removing and installing guide plate
In the steps
| Step | Torque |
|---|---|
| Specified torque for bolts -2-: 2 Nm. | 2 Nm |
| Specified torque for bolts -3-: 3 Nm. | 3 Nm |
| Specified torque for bolts -4-: 3.5 Nm. | 3.5 Nm |
Removing and installing sliding sunroof adjustment control unit J245
In the steps
| Step | Torque |
|---|---|
| Torque wrench 210 Nm - V.A.G 1783- | 210 Nm |
| Fit drive -1-, and tighten bolts -4-. Specified torque: 4 Nm. | 4 Nm |
Removing and installing cover
In the steps
| Step | Torque |
|---|---|
| Torque wrench 210 Nm - V.A.G 1783- | 210 Nm |
| Tighten bolts -2-. Specified torque: 2.5 Nm. | 2.5 Nm |
Removing and installing sunroof roller blind
In the steps
| Step | Torque |
|---|---|
| Torque wrench 210 Nm - V.A.G 1783- | 210 Nm |
| Tighten bolts -5-. Specified torque: 2.5 Nm. | 2.5 Nm |
| Fit handle -4- and tighten screws -3-. Specified torque: 1 Nm. | 1 Nm |
Removing and installing tension bow
In the steps
| Step | Torque |
|---|---|
| Fit handle -4- and tighten screws -3-. Specified torque: 1 Nm. | 1 Nm |
63 – Bumpers
Assembly overview – bumper cover
1.1.1 Assembly overview – bumper cover, Polo, »standard« equipment versionTo the drawing →
All items:Specified torque
| Item | Part | Torque | Notes |
|---|---|---|---|
| 2 | Bolt | 2 Nm | Qty. 2 · Bolted to lock carrier. |
| 4 | Bolt | 2 Nm | Left and right · Points upwards. |
| 5 | Bolt | 2 Nm | Qty. 5 on each side · Bolted to wheel housing liner. |
| 6 | Bolt | 2 Nm | Qty. 3 · Bolted to lock carrier. |
1.1.2 Assembly overview – bumper cover, Polo BlueMotionTo the drawing →
All items:Specified torque
| Item | Part | Torque | Notes |
|---|---|---|---|
| 2 | Bolt | 2 Nm | Qty. 2 · Bolted to lock carrier. |
| 4 | Bolt | 2 Nm | Qty. 1 on each side · Points upwards. |
| 5 | Bolt | 2 Nm | Qty. 5 on each side · Bolted to wheel housing liner. |
| 6 | Bolt | 2 Nm | Qty. 3 · Bolted to lock carrier. |
1.1.3 Assembly overview – bumper cover, CrossPoloTo the drawing →
All items:Specified torque
| Item | Part | Torque | Notes |
|---|---|---|---|
| 2 | Bolt | 2 Nm | Qty. 2 · Bolted to lock carrier. |
| 4 | Bolt | 2 Nm | Left and right · Points upwards. |
| 5 | Bolt | 2 Nm | Qty. 5 on each side · Bolted to wheel housing liner. |
| 6 | Bolt | 2 Nm | Qty. 3 · Bolted to lock carrier. |
1.1.4 Assembly overview – bumper cover, Polo »GTI«To the drawing →
All items:Specified torque
| Item | Part | Torque | Notes |
|---|---|---|---|
| 2 | Bolt | 2 Nm | Qty. 2 · Bolted to lock carrier. |
| 4 | Bolt | 2 Nm | Left and right · Points upwards. |
| 5 | Bolt | 2 Nm | Qty. 5 on each side · Bolted to wheel housing liner. |
| 6 | Bolt | 2 Nm | Qty. 3 · Bolted to lock carrier. |
1.1.5 Assembly overview – bumper cover, Polo »R-Line«To the drawing →
| Item | Part | Torque | Notes |
|---|---|---|---|
| 2 | Bolts | 2 Nm | Qty. 2 · Bolted to lock carrier. |
| 4 | Bolts | 2 Nm | Left and right · Points upwards. |
| 5 | Bolts | 2 Nm | Qty. 5 on each side · Bolted to wheel housing liner. |
| 6 | Bolts | 2 Nm | Qty. 3 · Bolted to lock carrier. |
Assembly overview – impact bar
| Item | Part | Torque | Notes |
|---|---|---|---|
| 3 | Bolt | 8 Nm | Qty. 2 each on left and right. |
| 4 | Bolt | 8 Nm | Qty. 2 each on left and right. |
| 5 | Bolt | 8 Nm | Qty. 2 on each side |
| 7 | Bolt | 30 Nm | Qty. 3 on each side |
| 8 | Bolt | 8 Nm | Qty. 2 |
Assembly overview – add-on parts
1.3.5 Assembly overview – add-on parts, Polo »R-Line«To the drawing →
| Item | Part | Torque |
|---|---|---|
| 13 | Bolt | 2 Nm |
Assembly overview – bumper cover
2.1.1 Assembly overview – bumper cover, Polo, »standard« equipment versionTo the drawing →
All items:Specified torque
| Item | Part | Torque | Notes |
|---|---|---|---|
| 3 | Bolt | 2 Nm | Left and right · Points upwards. · Bolted to side panel. |
| 4 | Bolt | 2 Nm | Qty. 4 · Bolted to wheel housing liner. |
| 6 | Bolt | 2 Nm | Qty. 2 on each side · Bolted to rear panel. |
2.1.2 Assembly overview – bumper cover, Polo BlueMotionTo the drawing →
All items:Specified torque
| Item | Part | Torque | Notes |
|---|---|---|---|
| 3 | Bolt | 2 Nm | Left and right · Points upwards. · Bolted to side panel. |
| 4 | Bolt | 2 Nm | Qty. 4 · Bolted to wheel housing liner. |
| 6 | Bolt | 2 Nm | Qty. 2 · Bolted to rear panel. |
2.1.3 Assembly overview – bumper cover, CrossPoloTo the drawing →
All items:Specified torque
| Item | Part | Torque | Notes |
|---|---|---|---|
| 3 | Bolt | 2 Nm | Left and right · Points upwards. · Bolted to side panel. |
| 4 | Bolt | 2 Nm | Qty. 4 · Bolted to wheel housing liner. |
| 6 | Bolt | 2 Nm | Qty. 2 · Bolted to rear panel. |
2.1.4 Assembly overview – bumper cover, Polo GTI, Polo BlueGTTo the drawing →
All items:Specified torque
| Item | Part | Torque | Notes |
|---|---|---|---|
| 3 | Bolt | 2 Nm | Left and right · Points upwards. · Bolted to side panel. |
| 4 | Bolt | 2 Nm | Qty. 4 · Bolted to wheel housing liner. |
| 6 | Bolt | 2 Nm | Qty. 2 · Bolted to rear panel. |
2.1.5 Assembly overview – bumper cover, Polo »R-Line«To the drawing →
| Item | Part | Torque | Notes |
|---|---|---|---|
| 3 | Bolts | 2 Nm | Left and right · Points upwards. · Bolted to side panel. |
| 4 | Bolts | 2 Nm | Qty. 4 · Bolted to wheel housing liner. |
| 5 | Bolts | 2 Nm | Qty. 2 · Bolted to rear panel. |
Assembly overview – impact bar
All except 8:Qty. 3 on each side
All except 2:Specified torque
| Item | Part | Torque | Notes |
|---|---|---|---|
| 2 | Hexagon nuts | 20 Nm | |
| 5 | Bolts | 2 Nm | |
| 8 | Bolts | 2 Nm | Qty. 4 |
64 – Glazing
Assembly overview – front door window
| Item | Part | Torque | Notes |
|---|---|---|---|
| 3 | Hexagon nut | 8 Nm | Qty. 4 |
| 6 | Bolt | 3 Nm | Qty. 3 |
Assembly overview – rear door window
| Item | Part | Torque | Notes |
|---|---|---|---|
| 5 | Hexagon nut | 8 Nm | Qty. 2 |
| 8 | Bolt | 3 Nm | Qty. 3 |
Removing and installing front door window
In the steps
| Step | Torque |
|---|---|
| Tighten bolts -3-, (qty. 2), specified torque: 8 Nm. | 8 Nm |
66 – Exterior equipment
Radiator grille and front trim
1.1.2 Assembly overview - radiator grilleTo the drawing →
| Item | Part | Torque | Notes |
|---|---|---|---|
| 2 | Bolts | 2 Nm | Qty. 2 |
| 5 | Bolt | 2 Nm |
Assembly overview – spoiler
2.1.2 Assembly overview – spoiler, Polo »GTI«To the drawing →
| Item | Part | Torque | Notes |
|---|---|---|---|
| 4 | Bolt | 10 Nm | Qty. 6 |
Assembly overview – side member trim
3.1.1 Assembly overview - side member trim, Polo »BlueMotion«, Polo »Blue GT«To the drawing →
All except 5:Qty. 1 on each side · Specified torque
| Item | Part | Torque | Notes |
|---|---|---|---|
| 2 | Bolt | 2 Nm | |
| 4 | Bolt | 2 Nm | |
| 5 | Self-cutting screw | 1.2 Nm | Qty. 8 on each side · Specified torque: - 0.1 Nm |
3.1.2 Assembly overview - side member trim, Cross PoloTo the drawing →
| Item | Part | Torque | Notes |
|---|---|---|---|
| 3 | Bolt | 2 Nm | Qty. 1 on each side · Specified torque |
| 5 | Self-cutting screw | 1.2 Nm | Specified torque: - 0.1 Nm |
3.1.3 Assembly overview – side member trim, Polo »GTI«To the drawing →
| Item | Part | Torque | Notes |
|---|---|---|---|
| 2 | Bolt | 2 Nm | Qty. 1 on each side · Specified torque |
| 5 | Self-cutting screw | 1.2 Nm | Specified torque: - 0.1 Nm |
Removing and installing retaining strip for side member trim
3.10.2 Removing and installing retaining strip for side member trim, CrossPolo, Polo »GTI«To the steps →
| Step | Torque |
|---|---|
| Tighten screws with least possible torque, i.e. 1.2 Nm - 0.1 Nm, so that screws are not excessively tightened. | 1.2 Nm / 0.1 Nm |
Removing and installing C-pillar trim on door
In the steps
| Step | Torque |
|---|---|
| Tighten bolt -2-, specified torque: 1 Nm. | 1 Nm |
Removing and installing front wheel arch trim
In the steps
| Step | Torque |
|---|---|
| Tighten bolt -2- to specified torque of 2 Nm. | 2 Nm |
Removing and installing rear wheel arch trim
In the steps
| Step | Torque |
|---|---|
| Tighten bolt 2 to specified torque of 2 Nm. | 2 Nm |
Assembly overview – noise insulation
4.1.1 Assembly overview - noise insulation, diesel enginesTo the drawing →
| Item | Part | Torque | Notes |
|---|---|---|---|
| 2 | Bolt | 2 Nm | Qty. 4 on each side · Specified torque |
4.1.2 Assembly overview – noise insulation, long versionTo the drawing →
| Item | Part | Torque | Notes |
|---|---|---|---|
| 2 | Bolt | 2 Nm | Qty. 9 · Specified torque |
4.1.3 Assembly overview - noise insulation, short versionTo the drawing →
| Item | Part | Torque | Notes |
|---|---|---|---|
| 2 | Bolt | 2 Nm | Qty. 3 on each side · Specified torque |
Underbody cladding
5.1 Assembly overview - underbody claddingTo the drawing →
| Item | Part | Torque | Notes |
|---|---|---|---|
| 2 | Hexagon nut | 2 Nm | Qty. 9 · Specified torque |
5.2 Assembly overview - tunnel cross-pieceTo the drawing →
| Item | Part | Torque | Notes |
|---|---|---|---|
| 2 | Hexagon nut | 20 Nm | Qty. 4 on each side · Specified torque |
Roof moulding and roof railing
6.1 Assembly overview - roof railingTo the drawing →
All items:Specified torque
| Item | Part | Torque | Notes |
|---|---|---|---|
| 3 | Hexagon nut | 9 Nm | Qty. 2 each on left and right at front |
| 4 | Hexagon nut | 9 Nm | Qty. 2 each on left and right at rear |
Assembly overview – exterior mirror
All items:Qty. 3
| Item | Part | Torque |
|---|---|---|
| 3 | Bolt | 1 Nm |
| 8 | Bolt | 1 Nm |
Removing and installing exterior mirror
7.2.1 Removing and installing exterior mirror, manually operatedTo the steps →
| Step | Torque |
|---|---|
| Tighten bolt -4-. Specified torque: 12 Nm. | 12 Nm |
| Tighten securing nut -6-. Specified torque: 1.5 Nm. | 1.5 Nm |
7.2.2 Removing and installing exterior mirror, electrically operatedTo the steps →
| Step | Torque |
|---|---|
| Tighten bolt -4-. Specified torque: 12 Nm. | 12 Nm |
Removing and installing mirror adjustment unit
In the steps
| Step | Torque |
|---|---|
| Torque wrench 210 Nm - V.A.G 1783- | 210 Nm |
| Specified torque for bolts -3-: 2 Nm. | 2 Nm |
Assembly overview – front wheel housing liner
| Item | Part | Torque | Notes |
|---|---|---|---|
| 3 | Bolt | 2 Nm | Qty. 13 · Specified torque |
Assembly overview – rear wheel housing liner
| Item | Part | Torque | Notes |
|---|---|---|---|
| 2 | Bolt | 2 Nm | Qty. 10 · Specified torque |
Removing and installing badges on front
9.4.3 Removing and installing front emblems, Polo BlueGTTo the table →
| Part | Torque |
|---|---|
| Badge | 2.0 Nm |
Assembly overview – towing bracket
| Item | Part | Torque | Notes |
|---|---|---|---|
| 6 | Bolt | 50 Nm +90° | Qty. 2 on each side · Always renew bolts after loosening |