1.6 TDI CR engine (EA189) · VW Polo 6R
Tightening torques
Every tightening torque the 1.6 TDI CR engine (EA189) manual gives for the VW Polo 6R, by repair group and procedure. Each one links to its drawing or table in the procedure.
- 242 torques
- 61 procedures
10 – Removing and installing engine
Installing engine
1.4.1 Notes on installing, PoloTo the table →
| Part | Torque |
|---|---|
| Nuts and bolts M6 M7 M8 M10 M12 | 10 Nm |
1.4.1 Notes on installing, PoloTo the steps →
| Step | Torque |
|---|---|
| 1) Specified torque for M 12 flange bolts: 75 Nm | 75 Nm |
Assembly overview – assembly mountings
2.1.2 Assembly overview – assembly mountings, PoloTo the drawing →
All items:Renew
| Item | Part | Torque | Notes |
|---|---|---|---|
| 4 | Bolt | 20 Nm +90° | |
| 6 | Nut | 40 Nm +90° | May only be unscrewed to renew engine mounting -item 3- |
| 7 | Threaded pin | 30 Nm +90° | |
| 8 | Bolt | 30 Nm +90° |
2.1.2 Assembly overview – assembly mountings, PoloTo the table →
| Part | Torque |
|---|---|
| 1) | 7 Nm |
| 2) | 40 Nm |
13 – Crankshaft group
Assembly overview – poly V-belt drive
1.1.1 Assembly overview - poly V-belt drive with tensioning roller and air conditioner compressorTo the drawing →
| Item | Part | Torque | Notes |
|---|---|---|---|
| 4 | Bolt | 10 Nm + 90° | Renew |
1.1.2 Assembly overview - poly V-belt drive with tensioning element and air conditioner compressorTo the drawing →
| Item | Part | Torque | Notes |
|---|---|---|---|
| 4 | Bolt | 10 Nm + 90° | Renew |
| 7 | + turn 90° further | 20 Nm |
Removing and installing poly-V belt
1.2.2 Removing and installing poly V-belt, poly V-belt drive with tensioning roller and air-conditioning compressorTo the table →
| Part | Torque |
|---|---|
| 4) | 30 Nm |
1.2.2 Removing and installing poly V-belt, poly V-belt drive with tensioning roller and air-conditioning compressorTo the steps →
| Step | Torque |
|---|---|
| Restore coolant lines -5- to their installation position, tighten -3, 4, 6-. 8 Nm. | 8 Nm |
Removing and installing tensioner for poly V-belt
In the steps
| Step | Torque |
|---|---|
| Restore coolant lines -5- to their installation position, tighten -3, 4, 6-. 8 Nm. | 8 Nm |
Removing and installing bracket for ancillaries
In the steps
| Step | Torque |
|---|---|
| Lifting eye bolts -A- and -B- 20 Nm. | 20 Nm |
| Part | Torque |
|---|---|
| 2) | 40 Nm |
Renewing crankshaft oil seal – belt pulley end
In the steps
| Step | Torque |
|---|---|
| Torque wrench (5 … 50 Nm) - V.A.G 1331- | 50 Nm |
| Torque wrench (40 … 200 Nm) - V.A.G 1332- | 200 Nm |
Removing and installing sealing flange on pulley end
In the steps
| Step | Torque |
|---|---|
| Torque wrench (5 … 50 Nm) - V.A.G 1331- | 50 Nm |
| Torque wrench (40 … 200 Nm) - V.A.G 1332- | 200 Nm |
| Tighten securing bolts for sealing flange to 15 Nm using alternate and diagonal sequence. | 15 Nm |
Assembly overview – cylinder block, gearbox end
| Item | Part | Torque | Notes |
|---|---|---|---|
| 1 | Bolt | 60 Nm +90° | Renew |
| 5 | Bolt | 4.5 Nm |
| Part | Torque |
|---|---|
| 2) | In diagonal sequence and in stages; final torque 15 Nm |
Removing and installing sealing flange on gearbox side
2.3.6 D - Pressing sender wheel onto crankshaft flange using assembly tool - T10134-To the steps →
| Step | Torque |
|---|---|
| Tighten hexagon nut of assembly tool - T10134- to 35 Nm using torque wrench - V.A.G 1331- and tool insert, 24 mm - V.A.G 1332/11-. | 35 Nm |
| After hexagon nut is tightened to 35 Nm, a small air gap must still be present between cylinder block and sealing flange. | 35 Nm |
2.3.7 e) Checking sender wheel installation position on crankshaftTo the steps →
| Step | Torque |
|---|---|
| Install flywheel using new bolts. Tighten securing bolts to 60 Nm + 90° further. | 60 Nm + 90° |
2.3.8 f) Re-pressing sender wheelTo the steps →
| Step | Torque |
|---|---|
| Tighten hexagon nut of assembly tool - T10134- to 40 Nm using torque wrench - V.A.G 1331- and tool insert, 24 mm - V.A.G 1332/11-. | 40 Nm |
| Tighten hexagon nut for assembly tool - T10134- to 45 Nm. | 45 Nm |
Assembly overview – crankshaft
| Item | Part | Torque | Notes |
|---|---|---|---|
| 5 | Bolts | 65 Nm +90° | Renew |
Measuring radial clearance of crankshaft
In the steps
| Step | Torque |
|---|---|
| Fit bearing cap and tighten bolts to 65 Nm without turning further angle and without rotating crankshaft. | 65 Nm |
Assembly overview – pistons and conrods
| Item | Part | Torque | Notes |
|---|---|---|---|
| 5 | Bolt | 30 Nm +90° | Renew · Oil threads and contact surface |
Checking radial clearance of conrods
In the steps
| Step | Torque |
|---|---|
| Fit conrod bearing cap and tighten to 30 Nm without turning further angle and without rotating crankshaft. | 30 Nm |
15 – Cylinder head, valve gear
Assembly overview – cylinder head
| Item | Part | Torque | Notes |
|---|---|---|---|
| 4 | Oil pressure switch - F1- | 22 Nm | Identification: green · 0.5 bar · If seal is leaking, nip open and renew. |
| 5 | 20 Nm | ||
| 7 | Glow pin plug | 18 Nm | |
| 10 | 10 Nm | ||
| 14 | 10 Nm | ||
| 17 | 25 Nm | ||
| 21 | 10 Nm |
Removing and installing cylinder head
1.2.1 Removing and installing cylinder head, PoloTo the steps →
| Step | Torque |
|---|---|
| Stage I = 35 Nm | 35 Nm |
| Step II = 60 Nm | 60 Nm |
Assembly overview – cylinder head cover
| Item | Part | Torque | Notes |
|---|---|---|---|
| 1 | 5 Nm | ||
| 3 | 22 Nm | ||
| 5 | further | 8 Nm +270° | Renew |
| 13 | 10 Nm |
Removing and installing cylinder head cover
In the steps
| Step | Torque |
|---|---|
| Tighten bolts to 10 Nm in sequence 1 … 6. | 10 Nm |
Removing and installing vacuum pump
In the steps
| Step | Torque |
|---|---|
| Install vacuum pump and tighten securing bolts to 10 Nm. | 10 Nm |
Assembly overview – toothed belt
2.1.2 Assembly overview - toothed belt, PoloTo the drawing →
| Item | Part | Torque | Notes |
|---|---|---|---|
| 2 | + turn 90° further | 120 Nm | Renew · Use counterhold - 3415 - to loosen and tighten. · Do not additionally oil or grease the threads and shoulder · Turning further can be done in several stages. |
| 4 | 20 Nm | ||
| 6 | + turn 45° further | 20 Nm | Renew |
| 8 | + turn 45° further | 20 Nm | Renew |
| 10 | 15 Nm | ||
| 11 | 100 Nm | ||
| 14 | 20 Nm | ||
| 15 | 10 Nm | Renew | |
| 17 | + turn 90° further | 50 Nm | |
| 19 | 95 Nm | ||
| 21 | 20 Nm | Renew | |
| 23 | 15 Nm | ||
| 26 | 9 Nm | ||
| 27 | + turn 90° further | 10 Nm | Renew |
| 29 | 5 Nm | ||
| 31 | + turn 180° further | 40 Nm | Renew |
2.1.2 Assembly overview - toothed belt, PoloTo the steps →
| Step | Torque |
|---|---|
| Renew stud for idler pulley only if damaged. Specified torque for stud: 15 Nm. | 15 Nm |
| Renew stud for tensioning roller only if damaged. Specified torque for stud: 15 Nm. | 15 Nm |
| Tighten bolts -arrows- to 9 Nm. | 9 Nm |
Removing and installing toothed belt
In the steps
| Step | Torque |
|---|---|
| Secure tensioning roller with 2 - 4 Nm. | 4 Nm |
| Hold tensioning roller in this position and tighten tensioning roller securing nut as follows: 20 Nm and 45° further. | 20 Nm +45° |
| In this position, first tighten securing bolts -1- of camshaft pulley and of toothed belt pulley for high pressure pump by hand and then tighten to 20 Nm. | 20 Nm |
| Hold tensioning roller in this position and tighten tensioning roller securing nut -1-: 20 Nm and turn 45° further. | 20 Nm +45° |
| Tighten securing bolts -arrows- for camshaft pulley hand-tight at first and then to 20 Nm. | 20 Nm |
| Tighten securing bolts for high-pressure pump toothed belt pulley hand-tight at first and then to 20 Nm. | 20 Nm |
| Tighten securing bolts of camshaft toothed belt pulley by hand first and then tighten to 20 Nm. | 20 Nm |
| Tighten securing bolts of camshaft toothed belt pulley by hand first and then tighten to 20 Nm. | 20 Nm |
| Install belt pulley vibration damper: specified torque 10 Nm +90° turn further. | 10 Nm +90° |
Assembly overview – valve gear
| Part | Torque |
|---|---|
| 2) | 10 Nm |
Measuring radial play of camshaft
In the steps
| Step | Torque |
|---|---|
| Fit retaining frame and tighten to 10 Nm ⇒ 3.1 Assembly overview - valve gear without twisting crankshafts. | 10 Nm |
Removing and installing camshaft
3.5.2 InstallingTo the steps →
| Step | Torque |
|---|---|
| Tighten retaining frame bolts to final torque in the sequence -1 … 24-. Specified torque: 10 Nm | 10 Nm |
| Tighten hub securing bolt -1- to 100 Nm. To do this, use the counterhold - T10051-. | 100 Nm |
17 – Lubrication
Assembly overview – sump/oil pump
| Item | Part | Torque | Notes |
|---|---|---|---|
| 3 | Oil drain plug | 30 Nm | |
| 7 | Bolt | 16 Nm | |
| 13 | Bolt | 9 Nm | |
| 16 | Bolt | 9 Nm | |
| 19 | Bolt | 16 Nm | |
| 20 | Bolt | 9 Nm | Self-locking · Renew |
| 1 | Bolt with pressure relief valve | 27 Nm |
| Part | Torque |
|---|---|
| 1) | In diagonal sequence to 5 Nm |
| 2) | 40 Nm |
| 3) | Diagonally in stages; final torque 13 Nm |
Removing and installing sump
In the steps
| Step | Torque |
|---|---|
| Torque wrench (5 … 50 Nm) - V.A.G 1331- | 50 Nm |
Assembly overview – engine oil cooler
| Item | Part | Torque |
|---|---|---|
| 1 | Cap | 25 Nm |
| 7 | 11 Nm |
Removing and installing engine oil cooler
In the steps
| Step | Torque |
|---|---|
| Step 2: tighten to 5 Nm | 5 Nm |
| Step 3: tighten to 11 Nm | 11 Nm |
Assembly overview – oil filter housing
| Item | Part | Torque |
|---|---|---|
| 1 | Cap | 25 Nm |
| 7 | 11 Nm |
| Part | Torque |
|---|---|
| 1) | In diagonal sequence to 14 Nm |
In the steps
| Step | Torque |
|---|---|
| Specified torque: 20 Nm | 20 Nm |
Assembly overview – oil circuit
4.1.2 Assembly overview - oil supply line, PoloTo the drawing →
| Item | Part | Torque | Notes |
|---|---|---|---|
| 1 | Ribbed bolt | 14 Nm | Renew |
| 2 | 22 Nm | Union nut of oil supply line on turbocharger | |
| 5 | 14 Nm | ||
| 6 | 22 Nm | Renew | |
| 8 | 10 Nm | ||
| 10 | Banjo bolt | 60 Nm | Renew |
| 11 | Banjo bolt | 30 Nm | Renew · Renew seals |
| 12 | 9 Nm |
Oil spray jets/nozzles
| Item | Part | Torque |
|---|---|---|
| 1 | Bolt with pressure relief valve | 27 Nm |
19 – Cooling
Assembly overview – coolant pump, thermostat
2.1.1 Assembly overview - coolant pump, thermostatTo the drawing →
| Item | Part | Torque |
|---|---|---|
| 2 | 15 Nm | |
| 6 | Bolt | 13 Nm |
2.1.2 Assembly overview - coolant pump / thermostat with 4/2-way valveTo the drawing →
| Item | Part | Torque |
|---|---|---|
| 2 | 15 Nm | |
| 6 | 15 Nm |
Removing and installing coolant pump
In the steps
| Step | Torque |
|---|---|
| Torque wrench (5 … 50 Nm) - V.A.G 1331- | 50 Nm |
| Insert coolant pump -2- in cylinder block, and tighten securing bolts -1- to 15 Nm. | 15 Nm |
Removing and installing 4/2-way valve with thermostat
In the steps
| Step | Torque |
|---|---|
| Tighten securing bolts -3- using T-bar and socket, 10 mm - 3185-. Specified torque: 15 Nm. | 15 Nm |
Assembly overview – coolant pipes
3.1.2 Assembly overview - coolant pipes, PoloTo the drawing →
| Item | Part | Torque |
|---|---|---|
| 1 | Bolt | 2.7 Nm |
| 5 | Bolt | 40 Nm |
| 8 | Bolt | 9 Nm |
| 10 | Bolt | 9 Nm |
| 14 | Bolt | 9 Nm |
| 19 | Threaded pin | 9 Nm |
| 20 | Bolt | 9 Nm |
| 22 | Bolt | 40 Nm |
Assembly overview – radiator/radiator fan
4.1.2 Assembly overview - radiator/radiator fan, PoloTo the drawing →
| Item | Part | Torque | Notes |
|---|---|---|---|
| 5 | 5 Nm | ||
| 9 | 5 Nm | ||
| 18 | Radiator fan thermal switch - F18- | 35 Nm | For radiator fan. · Switching temperatures: |
21 – Turbocharging/supercharging
Assembly overview – turbocharger
1.1.2 Assembly overview - turbocharger, PoloTo the drawing →
| Item | Part | Torque | Notes |
|---|---|---|---|
| 6 | 14 Nm | ||
| 8 | Exhaust gas temperature sender 1 - G 235- | 45 Nm | |
| 9 | 10 Nm | ||
| 12 | 10 Nm | ||
| 15 | Banjo bolt | 60 Nm | Renew complete with O-rings. |
| 17 | Ribbed bolt | 14 Nm | Renew |
| 18 | Banjo bolt | 30 Nm | Renew complete with oil seals. |
| 22 | 9 Nm |
Renewing vacuum unit for turbocharger
In the steps
| Step | Torque |
|---|---|
| Tighten securing bolts -arrows- to 8 Nm. | 8 Nm |
Assembly overview – charge air system
2.1.3 Assembly overview - charge air system, PoloTo the drawing →
| Item | Part | Torque |
|---|---|---|
| 3 | Screw-type clip | 8 Nm |
| 6 | 5 Nm | |
| 9 | 10 Nm |
Assembly overview – charge-air hose connections
2.3.1 Hose connections with grooved unionsTo the drawing →
| Item | Part | Torque |
|---|---|---|
| 1 | Hose clip -a- = 13 mm wide: | 5.5 Nm |
| 2 | Hose clip -b- = 9 mm wide: | 3 Nm |
23 – Mixture preparation – injection
Schematic overview – fuel system
1.1.1 Schematic overview - fuel system, PoloTo the drawing →
| Item | Part | Torque | Notes |
|---|---|---|---|
| 5 | Fuel pressure regulating valve - N 276- | 80 Nm | Renew |
Assembly overview – fuel system
1.2.1 Assembly overview - fuel system, PoloTo the drawing →
| Item | Part | Torque | Notes |
|---|---|---|---|
| 2 | Fuel pressure regulating valve - N 276- | 80 Nm | Cannot be re-installed. |
| 4 | Bolt | 10 Nm | |
| 6 | Bolt | 20 Nm +180° | Renew |
| 8 | Nut | 95 Nm | |
| 9 | Toothed belt pulley on high-pressure pump | 20 Nm | Bolts · Renew |
| 10 | Bolt | 20 Nm +45° | Renew |
| 11 | Bolt | 10 Nm | |
| 12 | High-pressure line | 28 Nm | Between high-pressure pump and fuel rail · Install so that component is not under tension |
| 13 | Fuel pressure sender - G 247- | 100 Nm | |
| 15 | Bolt | 22 Nm | |
| 16 | High-pressure lines | 28 Nm | Between fuel rail and injectors · Do not interchange · Install so that component is not under tension |
1.2.1 Assembly overview - fuel system, PoloTo the steps →
| Step | Torque |
|---|---|
| Tighten securing bolts to a maximum of 1 to 2 Nm at first. | 2 Nm |
| After the high-pressure lines have been fitted. Final specified torque: 8 Nm + turn 270° further. | 8 Nm |
Assembly overview – injectors
In the steps
| Step | Torque |
|---|---|
| Tighten securing bolts to a maximum of 1 to 2 Nm at first. | 2 Nm |
| After the high-pressure lines have been fitted. Final specified torque: 8 Nm + turn 270° further. | 8 Nm |
Removing and installing injectors
3.5.2 InstallingTo the steps →
| Step | Torque |
|---|---|
| Tighten bolt for clamp to a maximum of only 1 to 2 Nm at first. | 2 Nm |
Removing and installing fuel rail
In the steps
| Step | Torque |
|---|---|
| Initially tighten securing bolts -arrows- to just max. 1 - 2 Nm. | 2 Nm |
Assembly overview – high-pressure pump
All except 6, 9:Renew
| Item | Part | Torque | Notes |
|---|---|---|---|
| 2 | Bolt | 20 Nm +180° | Qty. 2 |
| 5 | Bolt | 20 Nm | Qty. 3 |
| 6 | Nut | 95 Nm | |
| 7 | Bolt | 20 Nm +45° | |
| 9 | High-pressure line | 28 Nm | Between high-pressure pump and fuel rail · Do not alter shape. · Check for damage before re-installing. · When renewing high-pressure pump, also renew high-pressure line. · Lubricate thread of union nuts with clean engine oil |
Removing and installing high-pressure pump
In the steps
| Step | Torque |
|---|---|
| In illustration 1 = 8 Nm | 8 Nm |
| In illustration 3 = 8 Nm | 8 Nm |
| In illustration 4 = 20 Nm | 20 Nm |
Lambda probe
6.1.3 Assembly overview - lambda probe, PoloTo the drawing →
| Item | Part | Torque | Notes |
|---|---|---|---|
| 4 | Pressure differential sender - G505- | 45 Nm | |
| 5 | Lambda probe - G39- with Lambda probe heater - Z19- | 55 Nm | Removing and installing · New Lambda probes are coated with an assembly paste · Assembly paste or hightemperature paste must not get into the slots in the Lambda probe · Catalogue (ETKA). |
Assembly overview – air filter housing
7.1.2 Assembly overview - air filter housing, PoloTo the drawing →
| Item | Part | Torque | Notes |
|---|---|---|---|
| 1 | Bolt | 2 Nm | |
| 5 | Bolt | 2 Nm | |
| 7 | Bolt | 8 Nm | |
| 10 | Bolt | 2 Nm | |
| 16 | Intake connecting pipe | 9 Nm | With captive bolt |
Assembly overview – intake manifold
8.1.1 Assembly overview - intake manifold, vehicles with intake manifold flap - V157-To the drawing →
| Item | Part | Torque | Notes |
|---|---|---|---|
| 2 | 9 Nm | ||
| 5 | Clamp | 5 Nm | Renew |
| 7 | 9 Nm | ||
| 9 | 10 Nm | ||
| 10 | 10 Nm | ||
| 11 | 10 Nm |
8.1.2 Assembly overview - intake manifold with attachments, vehicles without intake manifold flapTo the drawing →
| Item | Part | Torque | Notes |
|---|---|---|---|
| 4 | 8 Nm | ||
| 6 | 9 Nm | ||
| 9 | 9 Nm | ||
| 12 | 9 Nm | ||
| 14 | Clip | 5 Nm | Renew |
| 16 | 8 Nm | ||
| 19 | 8 Nm | ||
| 20 | 9 Nm |
26 – Exhaust system
Assembly overview – silencers
1.1.3 Assembly overview - silencers, PoloTo the drawing →
| Item | Part | Torque | Notes |
|---|---|---|---|
| 1 | Exhaust pipe with silencer | 25 Nm | Coupling point · Marked by indentation on exhaust pipe. · As standard, exhaust pipe and rear silencer are installed as a single component. For repairs, exhaust pipe and silencer are supplied with a clamp separately · Cut through separating point on connecting pipe at right angles using e.g. pneumatic sabre saw - V.A.G 1523A- (wear eye protection). · Position double repair clamp at side marks when installing. · Tighten bolts of repair double clamp evenly, specified torque: M8 = , M10 = 40 Nm |
| 2 | Retaining ring | 23 Nm | Renew if damaged |
| 3 | 20 Nm |
1.1.4 Separating exhaust systemTo the steps →
| Step | Torque |
|---|---|
| Tighten bolt connections of double clamps evenly to 23 Nm. | 23 Nm |
Aligning exhaust system free of stress
1.2.2 Aligning exhaust system free of stress, PoloTo the steps →
| Step | Torque |
|---|---|
| Then evenly tighten securing nuts -arrows- of foremost clamp. Specified torque: M8 = 25 Nm, M10 = 40 Nm. | 25 Nm / 40 Nm |
Installation position of clamp
In the steps
| Step | Torque |
|---|---|
| Specified torque: 25 Nm | 25 Nm |
| Specified torque: 35 Nm | 35 Nm |
| Specified torque: M8 = 25 Nm, M10 = 40 Nm | 25 Nm / 40 Nm |
Assembly overview – emission control
2.1.3 Assembly overview - front exhaust pipe with particulate filter, Polo, left-hand driveTo the drawing →
| Item | Part | Torque | Notes |
|---|---|---|---|
| 2 | 3 Nm | ||
| 5 | Exhaust gas temperature sender 4 - G 648- | 45 Nm | Lubricate thread of sender using high-temperature paste - G 052 112 A3- |
| 6 | Lambda probe - G 39- | 50 Nm | Grease only thread with high-temperature paste · Ensure that no hightemperature paste - G 052 112 A3- enters slots of probe body. · To remove use Lambda probe open ring spanner set - 3337-. · G 052 112 A3-. |
| 8 | 9 Nm | ||
| 11 | Clip | 7 Nm | Renew |
| 12 | 25 Nm | ||
| 13 | 25 Nm | ||
| 15 | Exhaust gas temperature sender 3 - G 495- | 45 Nm | Lubricate thread of sender using high-temperature paste - G 052 112 A3- · To remove, use tool set - T10395/6 -. |
| 17 | 25 Nm | ||
| 18 | 45 Nm | For control line |
2.1.4 Assembly overview - front exhaust pipe with particulate filter, Polo, right-hand driveTo the drawing →
| Item | Part | Torque | Notes |
|---|---|---|---|
| 1 | Lambda probe - G 39- | 50 Nm | Grease only thread with high-temperature paste · Ensure that no hightemperature paste - G 052 112 A3- enters slots of probe body. · To remove use Lambda probe open ring spanner set - 3337-. · G 052 112 A3-. |
| 3 | Clip | 7 Nm | Renew |
| 4 | Exhaust gas temperature sender 4 - G 648- | 45 Nm | Lubricate thread of sender using high-temperature paste - G 052 112 A3- |
| 5 | Exhaust gas temperature sender 3 - G 495- | 45 Nm | Lubricate thread of sender using high-temperature paste - G 052 112 A3- |
| 10 | 4.5 Nm | ||
| 11 | 25 Nm | ||
| 12 | 25 Nm |
Removing and installing particulate filter
2.2.3 Removing and installing particulate filter, Polo, right-hand driveTo the steps →
| Step | Torque |
|---|---|
| 3. Tighten clamp -2- to turbocharger 7 Nm | 7 Nm |
| 4) Tighten left nut -6- to crankcase 25 Nm | 25 Nm |
| 5) Tighten right nut -4- to crankcase 25 Nm | 25 Nm |
| 6) Tighten left bolt -7- of bracket to diesel particulate filter 25 Nm | 25 Nm |
| 7) Tighten right bolt -5- of bracket to diesel particulate filter 25 Nm | 25 Nm |
Assembly overview – exhaust gas temperature regulation
3.1.2 Assembly overview - exhaust gas temperature regulation, Polo (LHD)To the drawing →
| Item | Part | Torque | Notes |
|---|---|---|---|
| 2 | Control cable | 45 Nm | |
| 4 | Nut | 9 Nm | |
| 10 | Bolt | 4.5 Nm | |
| 11 | Bolt | 8 Nm | |
| 12 | Exhaust gas temperature sender 3 - G495- | 45 Nm | The thread of the exhaust gas temperature sender is coated and must not also be coated with high-temperature paste. · observe procedure. |
| 14 | Exhaust gas temperature sender 4 - G648- | 60 Nm | The thread of the exhaust gas temperature sender is coated and must not also be coated with hightemperature paste. |
| 15 | Exhaust gas temperature sender 1 - G235- | 45 Nm |
3.1.3 Assembly overview - exhaust gas temperature regulation, Polo (RHD)To the drawing →
All except 6:The thread of the exhaust gas temperature sender is coated and must not also be coated with high-temperature paste.
| Item | Part | Torque | Notes |
|---|---|---|---|
| 3 | Exhaust gas temperature sender 3 - G495- | 45 Nm | |
| 4 | Exhaust gas temperature sender 4 - G648- | 60 Nm | |
| 6 | Exhaust gas temperature sender 1 - G235- | 45 Nm | observe procedure. |
Removing and installing parts of exhaust gas temperature regulation
3.2.1 Removing and installing exhaust gas temperature sender 1 - G235-To the steps →
| Step | Torque |
|---|---|
| The torque wrench - V.A.G 1331- must be set to 28 Nm in this case. | 28 Nm |
| Extending the torque wrench - V.A.G 1331- with the spanner from tool set - T10395/7- allows the correct torque of 45 Nm to be achieved. | 45 Nm |
3.2.5 Removing and installing exhaust gas temperature sender 3 - G495-, Polo LHD vehiclesTo the steps →
3.2.6 Removing and installing exhaust gas temperature sender 3 - G 495-, Polo RHD vehiclesTo the steps →
3.2.7 Removing and installing exhaust gas temperature sender 4 - G 648-, Polo RHD vehiclesTo the steps →
| Step | Torque |
|---|---|
| The torque wrench - V.A.G 1331- must be set to 29 Nm in this case. | 29 Nm |
| Extending the torque wrench - V.A.G 1331- with the spanner from tool set - T10395/6- allows the correct torque of 45 Nm to be achieved. | 45 Nm |
Assembly overview – exhaust gas recirculation
| Item | Part | Torque | Notes |
|---|---|---|---|
| 1 | Bolt | 9 Nm | |
| 3 | Bolt | 9 Nm | |
| 6 | Bolt | 9 Nm | |
| 9 | Bolt | 9 Nm | |
| 10 | Clip | 5 Nm | Renew |
| 12 | Bolt | 9 Nm | |
| 16 | Nut | 22 Nm | Renew |
| 17 | Bolt | 9 Nm |
Cleaning exhaust gas recirculation system
4.5.1 Initiating cleaning of exhaust gas recirculation systemTo the steps →
| Step | Torque |
|---|---|
| Screw in bolts -arrows- and tighten to 9 Nm. | 9 Nm |
28 – Glow plug system
Removing and installing glow plug
In the steps
| Step | Torque |
|---|---|
| Specified torque is 18 Nm | 18 Nm |
Removing and installing engine speed sender G 28
In the steps
| Step | Torque |
|---|---|
| Installation is performed in the reverse order, observing the following: specified torques for engine speed sender - G28- securing bolt: 5 Nm. | 5 Nm |