1.6 TDI CR engine (EA189) · Crankshaft group · Cylinder block, gearbox end

Removing and installing sealing flange on gearbox side

Removing and installing sealing flange on gearbox side: drawing 1

Special tools and workshop equipment required

  • Assembly tool - T10134-
  • Torque wrench - V.A.G 1331-
  • Tool insert 24 mm - V.A.G 1332/11-
Removing and installing sealing flange on gearbox side: drawing 2
  • Depth gauge - VAS 6082-
  • 3 hexagon bolts M6 x 35 mm
  • 2 hexagon bolts M7 x 35 mm

2.3.1 Pressing out sealing flange with sender wheel

Removing and installing sealing flange on gearbox side: drawing 3
  • Detach intermediate plate at sealing flange and dowel pins -arrows-.
Removing and installing sealing flange on gearbox side: drawing 4
Removing and installing sealing flange on gearbox side: drawing 5
Removing and installing sealing flange on gearbox side: drawing 6
  • Remove bolts for sealing flange -1 … 6-.
Removing and installing sealing flange on gearbox side: drawing 7
  • To press out, screw in 3 bolts M6x35 -arrows- alternately into sealing flange not more than 1/2 turn at a time.
  • Remove sealing flange with sender wheel.

2.3.2 Pressing in sealing flange with sender wheel

Removing and installing sealing flange on gearbox side: drawing 8

Assembly tool - T10134-

A - Clamping surface

B - Hexagon nut

C - Assembly housing

D - Locating pin

E - Hexagon socket head bolt

F - Guide pin for diesel engines (black knob)

G - Guide pin for petrol engines (red knob)

2.3.3 a) Securing seal with sender wheel on assembly tool - T10134-

Removing and installing sealing flange on gearbox side: drawing 9
  • Screw in hexagon nut -B- to just before clamping surface -A- of threaded spindle.
Removing and installing sealing flange on gearbox side: drawing 10
  • Clamp assembly device - T10134- in a vice on clamping surface -A- of threaded spindle.
  • Press assembly housing -C- downwards until it rests against hexagon nut -B- -arrow-.
  • Screw hexagon nut onto threaded spindle until inner part of assembly device and assembly housing are at same height.
Removing and installing sealing flange on gearbox side: drawing 11
  • Remove securing clip -arrow- from new sealing flange.
Removing and installing sealing flange on gearbox side: drawing 12
  • Locating hole -A- on sender wheel -C- must align with marking
    • B- on sealing flange.
  • Place sealing flange with front side downwards on a clean flat surface.
Removing and installing sealing flange on gearbox side: drawing 13
  • Push sealing lip support ring -A- downwards in direction of arrow until it lies on flat surface.
Removing and installing sealing flange on gearbox side: drawing 14
  • Upper edge of sender wheel and front edge of sealing flange must align -arrows-.
Removing and installing sealing flange on gearbox side: drawing 15
  • Place sealing flange with front side on assembly tool - T10134- so that locating pin -B- can be inserted in sender wheel hole
    • A-.
Removing and installing sealing flange on gearbox side: drawing 16
  • Push sealing flange and support ring for sealing lip -B- against surface of assembly tool - T10134- whilst tightening 3 knurled screws -A- so that locating pin cannot slide out of sender wheel hole.

2.3.4 b) Securing assembling tool - T10134- with sealing flange on crankshaft flange

  • Crankshaft flange must be free of oil and grease.
  • Engine positioned at TDC No. 1 cylinder
Removing and installing sealing flange on gearbox side: drawing 17
  • Screw hexagon nut -B- to end of threaded spindle.
  • Press threaded spindle of assembly tool - T10134- in direction of arrow, until hexagon nut -B- lies against assembly housing
    • A-.
  • Align flat side of assembly housing on sump side of crankcase sealing surface.
Removing and installing sealing flange on gearbox side: drawing 18
  • Secure assembly tool - T10134- to crankshaft flange using hexagon socket head bolts -A-.
Removing and installing sealing flange on gearbox side: drawing 19
  • To guide sealing flange into cylinder block, screw in 2 M7 x 35 mm bolts (or bolts of comparable length ⇒ ⇒ Electronic parts catalogue (ETKA), standard parts) -A-.

2.3.5 c) Bolting assembly tool - T10134- onto crankshaft flange

Removing and installing sealing flange on gearbox side: drawing 20
  • Push assembly housing -C- by hand in direction of arrow until sealing lip support ring -B- contacts crankshaft flange -A-.
  • Push guide pin for diesel engines (black knob) -D- into hole in crankshaft. This ensures that the sender wheel reaches its final installation position.
  • Hand-tighten both hexagon socket head bolts of assembly tool.
  • Screw hexagon nut -E- onto threaded spindle by hand until it lies on assembly housing -C-.

2.3.6 D - Pressing sender wheel onto crankshaft flange using assembly tool - T10134-

Removing and installing sealing flange on gearbox side: drawing 21
  • Tighten hexagon nut of assembly tool - T10134- to 35 Nm using torque wrench - V.A.G 1331- and tool insert, 24 mm - V.A.G 1332/11-.

2.3.7 e) Checking sender wheel installation position on crankshaft

Removing and installing sealing flange on gearbox side: drawing 22
  • Screw hexagon nut -E- to end of threaded spindle.
  • Remove the two bolts -A- from cylinder block.
  • Screw the three knurled screws -B- out of sealing flange.
  • Remove assembly tool - T10134-.
  • Remove sealing lip support ring.
Removing and installing sealing flange on gearbox side: drawing 23
  • The sender wheel is in the correct installation position on the crankshaft if a gap -a- = 0.5 mm exists between crankshaft flange -A- and sender wheel -B-.
Removing and installing sealing flange on gearbox side: drawing 24
  • Position depth gauge - VAS 6082- on crankcase flange.
Removing and installing sealing flange on gearbox side: drawing 25
  • Measure distance between crankshaft flange -A- and sender wheel -B-.
  • Specification: dimension -a- = 0.5 mm

If dimension -a- is too small:

If dimension -a- is attained:

Removing and installing sealing flange on gearbox side: drawing 26

2.3.8 f) Re-pressing sender wheel

Removing and installing sealing flange on gearbox side: drawing 27
  • Secure assembly tool - T10134- to crankshaft flange using hexagon socket head bolts -A-.
  • Hand tighten both hexagon socket head bolts.
  • Push assembly tool - T10134- by hand to sealing flange.
Removing and installing sealing flange on gearbox side: drawing 22
  • Screw hexagon nut -E- onto threaded spindle by hand until it lies on assembly housing -C-.
Removing and installing sealing flange on gearbox side: drawing 21

If dimension -a- is still too small:

Tightening torques on this page

5 torques

2.3.6 D - Pressing sender wheel onto crankshaft flange using assembly tool - T10134-To the steps ↑

StepTorque
Tighten hexagon nut of assembly tool - T10134- to 35 Nm using torque wrench - V.A.G 1331- and tool insert, 24 mm - V.A.G 1332/11-.35 Nm
After hexagon nut is tightened to 35 Nm, a small air gap must still be present between cylinder block and sealing flange.35 Nm

2.3.7 e) Checking sender wheel installation position on crankshaftTo the steps ↑

StepTorque
Install flywheel using new bolts. Tighten securing bolts to 60 Nm + 90° further.60 Nm + 90°

2.3.8 f) Re-pressing sender wheelTo the steps ↑

StepTorque
Tighten hexagon nut of assembly tool - T10134- to 40 Nm using torque wrench - V.A.G 1331- and tool insert, 24 mm - V.A.G 1332/11-.40 Nm
Tighten hexagon nut for assembly tool - T10134- to 45 Nm.45 Nm

All tightening torques in this manual →