1.6 TDI CR engine (EA189) · Mixture preparation – injection · Injection system
Fuel system – assembly overview and fastening
⇒ 1.2.1 Assembly overview - fuel system, Polo
1.2.1 Assembly overview - fuel system, Polo
- 2 Fuel pressure regulating valve - N 276-
- Cannot be re-installed.
- Checking ⇒ 5.2 Checking fuel pressure regulating valve - N276-
- Removing and installing ⇒ 5.1 Removing and installing fuel pressure regulating valve - N 276-
- 80 Nm
- 3 Fuel return line
- Rigid.
- 4 Bolt
- 10 Nm
- 5 High-pressure pump
- Removing and installing ⇒ 4.2 Removing and installing high-pressure pump
- With fuel metering valve - N290- (do not open)
- After renewing, a first fuel filling must be performed (never allow the pump to run while it is still empty) ⇒ 1.3 Filling/bleeding fuel system.
- 6 Bolt
- 20 Nm + turn 180° further
- Renew
- 7 Hub
- With sender ring
- Use counterhold - T10051- to loosen and tighten.
- To remove, use puller - T40064-.
- 8 Nut
- 95 Nm
- 9 Toothed belt pulley on high-pressure pump
- Bolts 20 Nm
- Renew
- 10 Bolt
- 20 Nm + turn 45° further
- Renew
- 11 Bolt
- 10 Nm
- 12 High-pressure line
- 28 Nm
- Between high-pressure pump and fuel rail
- Install so that component is not under tension
- 13 Fuel pressure sender - G 247-
- Removing and installing ⇒ 5.3 Removing and installing fuel pressure sender - G 247-
- 100 Nm
- 14 High-pressure accumulator
- Removing and installing ⇒ 3.6 Removing and installing fuel rail
- 15 Bolt
- 22 Nm
- 16 High-pressure lines
- Removing and installing ⇒ 3.7 Removing and installing high-pressure lines
- 28 Nm
- Between fuel rail and injectors
- Do not interchange
- Install so that component is not under tension
- 17 Seal
- Renew if damaged ⇒ 1.4.1 Removing and installing injector seal in cylinder head cover.
- 18 Seal
- Renew if damaged ⇒ 1.4.1 Removing and installing injector seal in cylinder head cover.
- 19 Injectors
- Removing and installing ⇒ 3.5 Removing and installing injectors
- The following components and seals/O-rings must be renewed each time on removal/installation: “bolt for clamping piece”, “copper seal”, “O-ring of injector bore” and “retaining clip for return connection”.
- Before re-using “high-pressure line”, perform visual check of taper seats for damage such as transverse scores or corrosion; always renew if damaged.
- If they are to be re-installed, injectors, high-pressure fuel lines and clamping pieces must always be refitted in their original positions (i.e. on the same cylinder).
- 20 Bolt for clamp
- Renew
Tighten securing bolts to a maximum of 1 to 2 Nm at first.
After the high-pressure lines have been fitted. Final specified torque: 8 Nm + turn 270° further.
- 21 O-ring for fuel return lines
- The following component must be renewed any time the fuel return line is removed and installed: “return line retaining clip”
- Only renew O-ring if necessary
- Observe notes on installing ⇒ 1.2.1 Assembly overview - fuel system, Polo.
Removing O-ring for fuel return lines.
Proceed with extreme caution. Avoid damage to fuel return line.
- Lever old O-ring very carefully off fuel return line.
Do not work with a sharp-edged tool. Preferably use a plastic tool.
Installing O-ring for fuel return lines

A - Connection for »new« fuel return line, with indentation -arrow-, use orange O-ring.
B - Connection for »old« fuel return line, without indentation, use green O-ring.
Proceed with extreme caution. Avoid damage to the O-ring and fuel return line.
- Clean seating surfaces for O-rings on fuel return line very carefully.

- Carefully push O-ring -1- on its seat -2-.
Tightening torques on this page
13 torques
1.2.1 Assembly overview - fuel system, PoloTo the drawing ↑

| Item | Part | Torque | Notes |
|---|---|---|---|
| 2 | Fuel pressure regulating valve - N 276- | 80 Nm | Cannot be re-installed. |
| 4 | Bolt | 10 Nm | |
| 6 | Bolt | 20 Nm +180° | Renew |
| 8 | Nut | 95 Nm | |
| 9 | Toothed belt pulley on high-pressure pump | 20 Nm | Bolts · Renew |
| 10 | Bolt | 20 Nm +45° | Renew |
| 11 | Bolt | 10 Nm | |
| 12 | High-pressure line | 28 Nm | Between high-pressure pump and fuel rail · Install so that component is not under tension |
| 13 | Fuel pressure sender - G 247- | 100 Nm | |
| 15 | Bolt | 22 Nm | |
| 16 | High-pressure lines | 28 Nm | Between fuel rail and injectors · Do not interchange · Install so that component is not under tension |
1.2.1 Assembly overview - fuel system, PoloTo the steps ↑
| Step | Torque |
|---|---|
| Tighten securing bolts to a maximum of 1 to 2 Nm at first. | 2 Nm |
| After the high-pressure lines have been fitted. Final specified torque: 8 Nm + turn 270° further. | 8 Nm |