1.6 TDI CR engine (EA189) · Exhaust system · Emission control
Emission control – assembly overview and fastening
⇒ 2.1.3 Assembly overview - front exhaust pipe with particulate filter, Polo, left-hand drive
⇒ 2.1.4 Assembly overview - front exhaust pipe with particulate filter, Polo, right-hand drive
2.1.3 Assembly overview - front exhaust pipe with particulate filter, Polo, left-hand drive
- 1 Pressure differential sender - G 505-
- 2 3 Nm
- 3 Control lines
- 4 Clamps
- 5 Exhaust gas temperature sender 4 - G 648-, 45 Nm
- Lubricate thread of sender using high-temperature paste - G 052 112 A3-
- 6 Lambda probe - G 39-, 50 Nm
- Grease only thread with high-temperature paste
- G 052 112 A3-.
- Ensure that no hightemperature paste - G 052 112 A3- enters slots of probe body.
- To remove use Lambda probe open ring spanner set - 3337-.
- Grease only thread with high-temperature paste
- 7 Heat shield
- 8 9 Nm
- 9 Particulate filter
- Removing and installing ⇒ 2.2 Removing and installing particulate filter
- 10 Seal
- Renew
- Observe installation position
- 11 Clip
- 7 Nm
- Renew
- 12 25 Nm
- 13 25 Nm
- 14 Bracket
- Bolted to cylinder head
- 15 Exhaust gas temperature sender 3 - G 495-, 45 Nm
- Lubricate thread of sender using high-temperature paste - G 052 112 A3-
- To remove, use tool set - T10395/6 -.
- 16 Bracket
- 17 25 Nm
- 18 45 Nm
- For control line
- 19 Bracket
- For pressure differential sender - G 505-.

Installation position of clamp
- Position double clamp at distance -a- = 5 mm from marking on front exhaust pipe.
2.1.4 Assembly overview - front exhaust pipe with particulate filter, Polo, right-hand drive
- 1 Lambda probe - G 39-
- 50 Nm
- Grease only thread with high-temperature paste
- G 052 112 A3-.
- Ensure that no hightemperature paste - G 052 112 A3- enters slots of probe body.
- To remove use Lambda probe open ring spanner set - 3337-.
- 2 Seal
- Renew
- Observe installation position
- 3 Clip, 7 Nm
- Renew
- 4 Exhaust gas temperature sender 4 - G 648-
- 45 Nm
- Lubricate thread of sender using high-temperature paste - G 052 112 A3-
- Tightening ⇒ 3.2 Removing and installing parts of exhaust gas temperature regulation.
- 5 Exhaust gas temperature sender 3 - G 495-
- 45 Nm
- Lubricate thread of sender using high-temperature paste - G 052 112 A3-
- Tightening ⇒ 3.2 Removing and installing parts of exhaust gas temperature regulation.
- 6 Pressure differential sender - G 505- bracket
- 7 Clamps
- 8 Control lines
- 9 Pressure differential sender - G 505-
- Removing and installing ⇒ 5.6.4 Removing and installing pressure differential sender - G 505-, Polo, right-hand drive
- 10 4.5 Nm
- 11 25 Nm
- 12 25 Nm
- 13 Bracket
- Bolted to cylinder head
- 14 Particulate filter
- Removing and installing ⇒ 2.2.3 Removing and installing particulate filter, Polo, right-hand drive

Installation position of clamp
- Position double clamp at distance -a- = 5 mm from marking on front exhaust pipe.
Tightening torques on this page
17 torques
2.1.3 Assembly overview - front exhaust pipe with particulate filter, Polo, left-hand driveTo the drawing ↑

| Item | Part | Torque | Notes |
|---|---|---|---|
| 2 | 3 Nm | ||
| 5 | Exhaust gas temperature sender 4 - G 648- | 45 Nm | Lubricate thread of sender using high-temperature paste - G 052 112 A3- |
| 6 | Lambda probe - G 39- | 50 Nm | Grease only thread with high-temperature paste · Ensure that no hightemperature paste - G 052 112 A3- enters slots of probe body. · To remove use Lambda probe open ring spanner set - 3337-. · G 052 112 A3-. |
| 8 | 9 Nm | ||
| 11 | Clip | 7 Nm | Renew |
| 12 | 25 Nm | ||
| 13 | 25 Nm | ||
| 15 | Exhaust gas temperature sender 3 - G 495- | 45 Nm | Lubricate thread of sender using high-temperature paste - G 052 112 A3- · To remove, use tool set - T10395/6 -. |
| 17 | 25 Nm | ||
| 18 | 45 Nm | For control line |
2.1.4 Assembly overview - front exhaust pipe with particulate filter, Polo, right-hand driveTo the drawing ↑

| Item | Part | Torque | Notes |
|---|---|---|---|
| 1 | Lambda probe - G 39- | 50 Nm | Grease only thread with high-temperature paste · Ensure that no hightemperature paste - G 052 112 A3- enters slots of probe body. · To remove use Lambda probe open ring spanner set - 3337-. · G 052 112 A3-. |
| 3 | Clip | 7 Nm | Renew |
| 4 | Exhaust gas temperature sender 4 - G 648- | 45 Nm | Lubricate thread of sender using high-temperature paste - G 052 112 A3- |
| 5 | Exhaust gas temperature sender 3 - G 495- | 45 Nm | Lubricate thread of sender using high-temperature paste - G 052 112 A3- |
| 10 | 4.5 Nm | ||
| 11 | 25 Nm | ||
| 12 | 25 Nm |