1.6 TDI CR engine (EA189) · Cylinder head, valve gear · Toothed belt drive

Removing and installing toothed belt

Removing and installing toothed belt: drawing 1

Special tools and workshop equipment required

Removing and installing toothed belt: drawing 2
Removing and installing toothed belt: drawing 3
  • 2x diesel injection pump locking pin - 3359-
  • Crankshaft stop - T10050-
  • Counter-hold tool - T10172-
  • Angled screwdriver - T10264- for tensioning roller -A-
  • Locking tool - T10265-
  • Socket XZN 10 - T10385-
  • Angled screwdriver - T10409- for tensioning roller -B-

Not illustrated:

  • Torque wrench - V.A.G 1331-
  • Torque wrench - V.A.G 1332-

Observe different directions of rotation during tensioning

Removing and installing toothed belt: drawing 4

Features tensioning roller A

  • Locking tool - T10265- required for installation.
  • Check tensioning roller is seated correctly in timing belt guard.
  • Tension toothed belt by turning tensioning roller eccentric »clockwise«

Features tensioning roller B

  • Locking tool not required.
  • Tensioning roller is not seated in toothed belt guard.
  • Tension toothed belt by rotating tensioning roller eccentric »anticlockwise«
  • Remove engine cover panel ⇒ 3 Engine cover panel.
  • With ignition switched off, disconnect battery. ⇒ Electrical system; Rep. gr. 27; Battery; Disconnecting and connecting battery
  • Remove noise insulation:

    Polo ⇒ General body repairs, exterior; Rep. gr. 50; Noise insulation; Assembly overview - noise insulation

  • Remove poly V-belt ⇒ 13 – Crankshaft group.

Continuation for Polo ⇒ 2.2 Removing and installing toothed belt

Polo

Removing and installing toothed belt: drawing 5
  • Disconnect electrical connector -2- at pressure differential sender - G 505-.
  • Remove pressure differential sender - G 505- from bracket -3-.
  • Lay pressure differential sender - G 505- aside to rear together with lines.

Remove fuel filter with bracket.

Removing and installing toothed belt: drawing 6
  • To do this, open quick-release couplings -A- and -B- of fuel lines.
  • Catch any escaping fuel.
Removing and installing toothed belt: drawing 7
  • Use a finger to release locking lug of fuel pre-heater valve.
  • Pull fuel pre-heater valve upwards out of coolant expansion tank guide.
Removing and installing toothed belt: drawing 8
  • Unclip fuel filter from lower part of fuel filter.
  • Remove fuel filter upwards.
  • Separate fuel supply line and return line at engine end.
  • Remove fuel filter and fuel lines together with fuel preheater valve.
  • Remove lower part of fuel filter ⇒ Rep. gr. 20; Fuel filter; Removing and installing fuel filter.
Removing and installing toothed belt: drawing 9
  • Unscrew bolts -arrows- for coolant expansion tank.
  • Disconnect electrical connector -1- for coolant shortage indicator switch - F66-.
  • Lay coolant expansion tank to one side.
Removing and installing toothed belt: drawing 10
  • Open clips -arrows- and remove toothed belt guard.
  • Remove front right wheel housing liner.

Continued for all vehicles

Removing and installing toothed belt: drawing 11
  • Unscrew bolts -arrows-.
  • Remove toothed belt guard downwards.

Polo

Continued for all vehicles

Removing and installing toothed belt: drawing 12
  • Turn engine to TDC and lock crankshaft pulley in position with crankshaft stop - T10050-. Fit the crankshaft stop in the teeth from the face side of the toothed belt pulley.
  • The mark -2- on the toothed pulley and the arrow -1- on the crankshaft stop - T10050- must align -arrow-. When doing this, the pin of the crankshaft stop must engage in the drilling of sealing flange.
Removing and installing toothed belt: drawing 13

The arrow on the camshaft pulley must be at almost »12 o'clock«.

  • Mark direction of rotation of toothed belt.
Removing and installing toothed belt: drawing 14
  • Loosen bolts -arrows- approx. 90° for camshaft toothed belt pulley.
Removing and installing toothed belt: drawing 15
  • Loosen bolts -2- approx. 90° for high-pressure pump toothed belt pulley using bit XZN 10 - T10385-.

Tensioning roller A:

Removing and installing toothed belt: drawing 16
  • Loosen securing nut of tensioning roller -1- and turn tensioning roller eccentric using socket - T10264- counter-clockwise -arrow- until tensioning roller can be locked with locking pin - T10265-.
Removing and installing toothed belt: drawing 17
  • Now turn tensioning roller eccentric clockwise -arrow- onto stop and tighten securing nut -1- hand-tight.

Tensioning roller B:

Removing and installing toothed belt: drawing 18
  • Loosen nut -1- for belt tensioner.
  • Use angled screwdriver 8mm - T10409- to rotate eccentric of tensioning roller clockwise -arrow- until tensioning roller is loosened.
  • Retighten securing nut by hand.
  • Remove toothed belt first from idler pulley and then from remaining toothed belt pulleys.

Installing

Tensioning roller A:

Removing and installing toothed belt: drawing 19
Removing and installing toothed belt: drawing 20
  • Tensioning roller must be locked with locking tool - T10265- and secured to right stop.
  • Crankshaft is locked using crankshaft stop - T10050-.

Tensioning roller B:

Removing and installing toothed belt: drawing 21
  • Place tensioner for tensioning roller in 9 o'clock position.
  • Secure tensioning roller with 2 - 4 Nm.
Removing and installing toothed belt: drawing 22

Crankshaft is locked using crankshaft stop - T10050-.

Continuation for both tensioning rollers

Removing and installing toothed belt: drawing 23
  • Lock camshaft hub with locking pin - 3359-. To do this, slide locking pin through outer free elongated hole into hole in cylinder head.
Removing and installing toothed belt: drawing 24
  • Loosen bolt which had been tightened only hand-tight.

Bolts -arrows- screwed in loosely.

It should just be possible to turn camshaft toothed belt pulley without axial movement.

Removing and installing toothed belt: drawing 25

Positioning hub of high-pressure pump

Removing and installing toothed belt: drawing 26
  • Lock hub of high-pressure pump with locking pin - 3359-. To do this, slide locking pin into adjustment hole outside toothed belt pulley.

Loosely tightened bolts -1-.

It should just be possible to turn high-pressure pump toothed belt pulley without axial movement.

Removing and installing toothed belt: drawing 27
  • Turn camshaft toothed belt pulley -3- and toothed belt pulley of high-pressure pump -5- in their elongated holes clockwise to stop.
  • Fit toothed belt in sequence described:
  • 1 Crankshaft pulley
  • 2 Tensioning pulley
  • 3 Camshaft toothed belt pulley
  • 4 Coolant pump toothed belt pulley
  • 5 High-pressure pump toothed belt pulley
  • 6 Idler roller

Tensioning roller A:

  • Loosen tensioning roller securing nut and pull out locking tool - T10265-.
Removing and installing toothed belt: drawing 28
Removing and installing toothed belt: drawing 29
  • Screw eccentric of tensioning roller clockwise carefully using angled screwdriver - T10264-. Indicator -2- must be roughly past the centre of the gap in the base plate (corrects itself during pretensioning).

Ensure that securing nut -1- does not turn as well.

  • Hold tensioning roller in this position and tighten tensioning roller securing nut as follows: 20 Nm and 45° further.
Removing and installing toothed belt: drawing 30
  • Apply counterhold - T10172- as shown. Press counterhold - T10172- in direction of arrow, keeping camshaft toothed belt pulley under tension.
  • In this position, first tighten securing bolts -1- of camshaft pulley and of toothed belt pulley for high pressure pump by hand and then tighten to 20 Nm.

Tensioning roller B:

Removing and installing toothed belt: drawing 31
  • Carefully turn eccentric on tensioning roller counter clockwise using angled screwdriver - T10409-. Indicator -2- must be roughly past the centre of the gap in the base plate (corrects itself during pretensioning).
Removing and installing toothed belt: drawing 32

Markings on tensioning element and tensioning roller -arrow- are now almost aligned.

Ensure that securing nut -1- does not turn as well.

  • Hold tensioning roller in this position and tighten tensioning roller securing nut -1-: 20 Nm and turn 45° further.
Removing and installing toothed belt: drawing 30
  • Apply counterhold - T10172- as shown. Press counterhold - T10172- in direction of arrow, keeping camshaft toothed belt pulley under tension.
Removing and installing toothed belt: drawing 33
  • Tighten securing bolts -arrows- for camshaft pulley hand-tight at first and then to 20 Nm.
Removing and installing toothed belt: drawing 34
  • Tighten securing bolts for high-pressure pump toothed belt pulley hand-tight at first and then to 20 Nm.

Continuation for both tensioning rollers

  • Remove locking pins - 3359- and crankshaft stop - T10050-.
  • Turn crankshaft at least 2 rotations in engine direction of rotation and set again to TDC no. 1 cylinder.
  • Fit crankshaft stop - T10050- again to crankshaft belt pulley.
Removing and installing toothed belt: drawing 35
  • Now turn crankshaft in engine direction of rotation until pin of crankshaft stop -arrow- engages in sealing flange from rotational movement.
Removing and installing toothed belt: drawing 36
  • Ensure that:
  • Camshaft hub can be locked with locking pin - 3359-.
  • Belt tensioner indicator is centred or maximum 5 mm to right of base plate notch.

If camshaft hub cannot be locked:

  • Pull crankshaft stop - T10050- back until pin uncovers hole.
  • Turn crankshaft in opposite direction of engine rotation slightly past TDC.
  • Now turn crankshaft slowly in direction of engine rotation until camshaft hub can be secured in position.
  • After locking, loosen securing nuts of camshaft pulley.

If pin of crankshaft stop - T10050- is standing on left next to hole:

Removing and installing toothed belt: drawing 35
  • Turn crankshaft in engine direction of rotation until crankshaft stop pin engages in sealing flange whilst turning.
  • Tighten securing bolts of camshaft toothed belt pulley by hand first and then tighten to 20 Nm.

If pin of crankshaft stop - T10050- is standing on right next to hole:

  • Slightly turn crankshaft in opposite direction of engine rotation.
  • Now turn crankshaft in engine direction of rotation until crankshaft stop pin engages in sealing flange whilst turning.
  • Tighten securing bolts of camshaft toothed belt pulley by hand first and then tighten to 20 Nm.

Continuation

  • Remove locking pin - 3359- and crankshaft stop - T10050-.
  • Turn crankshaft at least 2 rotations in engine direction of rotation and set again to TDC no. 1 cylinder.
  • Repeat check.
  • If camshaft hub can be secured in position, tighten securing bolts as follows:
Removing and installing toothed belt: drawing 30
  • Camshaft toothed belt pulley: turn 45° further. Counterhold with counterhold - T10172- and adapters - T10172/4-.
  • Install centre and lower parts of toothed belt guard.
  • Install belt pulley vibration damper: specified torque 10 Nm +90° turn further.
  • Install poly V-belt.
  • Install upper toothed belt guard.

Further assembly is basically a reverse of the dismantling sequence. During this procedure, observe the following:

  • Ensure fuel hoses are seated correctly.
  • Do not interchange supply line and return line (return line blue or with blue marking, supply line white).
  • Install wheel housing liner.
  • Install noise insulation:

    Polo ⇒ General body repairs, exterior; Rep. gr. 50; Noise insulation; Assembly overview - noise insulation

Tightening torques on this page

9 torques

In the steps

StepTorque
Secure tensioning roller with 2 - 4 Nm.4 Nm
Hold tensioning roller in this position and tighten tensioning roller securing nut as follows: 20 Nm and 45° further.20 Nm +45°
In this position, first tighten securing bolts -1- of camshaft pulley and of toothed belt pulley for high pressure pump by hand and then tighten to 20 Nm.20 Nm
Hold tensioning roller in this position and tighten tensioning roller securing nut -1-: 20 Nm and turn 45° further.20 Nm +45°
Tighten securing bolts -arrows- for camshaft pulley hand-tight at first and then to 20 Nm.20 Nm
Tighten securing bolts for high-pressure pump toothed belt pulley hand-tight at first and then to 20 Nm.20 Nm
Tighten securing bolts of camshaft toothed belt pulley by hand first and then tighten to 20 Nm.20 Nm
Tighten securing bolts of camshaft toothed belt pulley by hand first and then tighten to 20 Nm.20 Nm
Install belt pulley vibration damper: specified torque 10 Nm +90° turn further.10 Nm +90°

All tightening torques in this manual →