1.6 TDI CR engine (EA189) · Cylinder head, valve gear · Valve gear
Removing and installing camshaft

Special tools and workshop equipment required
- Diesel injection pump locking pin - 3359-
- Counter-hold tool - T10051-
- Puller - T10052-
- Camshaft fitting tool - T40094-
- Camshaft clamping tool - T40095-
- Camshaft fitting tool - T40096-

- Torque wrench - V.A.G 1331/-

- Torque wrench - V.A.G 1332/-
- Sealant as per ⇒ Electronic Parts Catalogue (ETKA)
3.5.1 Removing
- Remove engine cover panel ⇒ 3 Engine cover panel.
- Remove fuel filter ⇒ Rep. gr. 20; Fuel filter; Removing and installing fuel filter.
- Removed toothed belt from camshaft and high-pressure pump ⇒ 2.2 Removing and installing toothed belt.
- Remove cylinder head cover ⇒ 1.4 Removing and installing cylinder head cover.

- Unscrew securing bolts -1- of camshaft sprocket.
- Detach camshaft pulley from hub.

- Counterhold hub with counterhold - T10051- and loosen securing bolt -1- of hub.
- Loosen hub securing bolt about 2 turns.

- Fit puller - T10052- and align it with holes in hub.
- Tighten securing bolts -1-.
- Apply tension to hub by evenly tightening puller -2- until hub separates from taper of camshaft.
- Remove hub from taper of camshaft.
- Remove vacuum pump ⇒ 1.5 Removing and installing vacuum pump.

- Remove securing bolts of retaining frame in sequence -24…1-.
- Release retaining frame carefully from adhesive.
- Mark camshafts for re-installation and remove.
3.5.2 Installing

Remove one-piece -arrow- camshaft sprocket

- Remove sealant residue from cylinder block and retaining frame using, for example, a plastic rotary brush.
- Clean sealing surfaces. They must be free of oil and grease.
- Lubricate running surfaces of camshafts.

Prepare camshaft fitting tool - T40094- as follows:
- Bolt supports -T40094/9- and -T40094/10- (with -T40094/11- ) to base plate as shown in illustration. Remove any bolted-on supports here if necessary.

- Place support -T40094/1- in position -F- and support - T40094/2- in position -A-.

- Insert inlet camshaft into supports -T40094/1- and - T40094/2-.
- Turn inlet camshaft so that it can be locked in “TDC” position with locking ruler -arrow 1-.
- The indentation -arrow 2- for the cylinder head bolt must face outwards.

- Insert exhaust camshaft into supports -T40094/9- and - T40094/10-.
- Lock exhaust camshaft with cover -T40094/11-.
- The lug -1- of the cover must engage in the slot -2- in the camshaft.
Vehicles with two-piece camshaft sprocket:
- Place clamping tool -T40096/1- on teeth of exhaust camshaft in such a way that the two arms of the tool engage on the two halves of the gear (one in each half, as shown in illustration).
- The wider arm must engage in the wider gear half.
- Tighten clamping tool using knurled wheel so that faces of gear teeth are in alignment.
Continued for all vehicles
- Slide inlet camshaft towards exhaust camshaft until teeth engage.

- Place retaining frame -1- on camshafts.
- All camshaft bearings must be seated on the camshafts.
- Fit camshaft fitting tool - T40095- and fix camshafts in position in retaining frame as shown in the illustration.

- Remove -T40094/11- cover.

- Cut off nozzle on tube at front marking (∅ of nozzle approx. 2 mm).
- Apply beads of sealant onto clean sealing surfaces of cylinder head as illustrated.
- Thickness of sealant beads: 2…3 mm.

- Install new cap flush on cylinder head.
- Remove camshafts together with retaining frame and clamping tool - T40095- from camshaft fitting tool - T40094-.
- Carefully insert camshafts and retaining frame into cylinder head.

- Hand-tighten retaining frame securing bolts in sequence -1 … 24- initially.
- The retaining frame should make contact with the cylinder head over the complete surface.
- Tighten retaining frame bolts to final torque in the sequence -1 … 24-. Specified torque: 10 Nm
- Remove camshaft fitting tool - T40095- and clamping tool - T40096/1-.
- Renew camshaft seal ⇒ 3.4 Removing and installing camshaft oil seal.
Perform further installation in reverse order, paying attention to the following:
- Place hub onto camshaft.

- Tighten hub securing bolt -1- to 100 Nm. To do this, use the counterhold - T10051-.

- Push camshaft sprocket onto hub.
- Hand tighten securing bolts -1- at camshaft sprocket so that there is no play.
- Lock hub with locking pin - 3359-.
- Install toothed belt and adjust valve timing ⇒ 2.2 Removing and installing toothed belt.
- Install vacuum pump ⇒ 1.5 Removing and installing vacuum pump.
- Install cylinder head cover ⇒ 1.4 Removing and installing cylinder head cover.
- Install fuel filter ⇒ Rep. gr. 20; Fuel filter; Removing and installing fuel filter.
Tightening torques on this page
2 torques
3.5.2 InstallingTo the steps ↑
| Step | Torque |
|---|---|
| Tighten retaining frame bolts to final torque in the sequence -1 … 24-. Specified torque: 10 Nm | 10 Nm |
| Tighten hub securing bolt -1- to 100 Nm. To do this, use the counterhold - T10051-. | 100 Nm |