1.6 TDI CR engine (EA189) · Cylinder head, valve gear · Toothed belt drive
Toothed belt – assembly overview and fastening
⇒ 2.1.2 Assembly overview - toothed belt, Polo
2.1.2 Assembly overview - toothed belt, Polo
- 1 Toothed belt
- Mark direction of rotation before removing
- Check for wear
- Do not kink
- Removing, installing and tensioning ⇒ 2.2 Removing and installing toothed belt.
- 2 120 Nm + turn 90° further
- Renew
- Use counterhold - 3415 - to loosen and tighten.
- Do not additionally oil or grease the threads and shoulder
- Turning further can be done in several stages.
- 3 Crankshaft pulley
- 4 20 Nm
- 5 Idler roller
- 6 20 Nm + turn 45° further
- Renew
- 7 Tensioning pulley
- Remove engine bracket in order to remove and install ⇒ 1.8.4 Removing and installing engine bracket, Polo
- 8 20 Nm + turn 45° further
- Renew
- 9 Camshaft sprocket
- 10 15 Nm
- 11 100 Nm
- 12 Hub
- Use counterhold - T10051- to loosen and tighten.
- To remove, use puller - T10052-
- Removing and installing ⇒ 3.5 Removing and installing camshaft
- 13 Rear toothed belt guard
- 14 20 Nm
- 15 10 Nm
- Renew
- 16 Idler roller
- 17 50 Nm + turn 90° further
- 18 Hub
- Use counterhold - T10051- to loosen and tighten.
- To remove, use puller - T40064-.
- 19 95 Nm
- 20 Toothed belt pulley on high-pressure pump
- 21 20 Nm
- Renew
- 22 Coolant pump
- Removing and installing ⇒ 2.2 Removing and installing coolant pump
- 23 15 Nm
- 24 Toothed belt guard upper part
- 25 Toothed belt guard lower part
- 26 9 Nm
- 27 10 Nm + turn 90° further
- Renew
- 28 Belt pulley and vibration damper
- Can only be installed in one position, holes are offset.
- 29 5 Nm
- Only fitted with protective plate from ⇒ Electronic Parts Catalogue (ETKA).
- 30 Protective plate
- 31 40 Nm + turn 180° further
- Renew
- Observe tightening sequence ⇒ 1.8.4 Removing and installing engine bracket, Polo
- 32 Engine support
- Removing and installing ⇒ 1.8.4 Removing and installing engine bracket, Polo

Lower toothed belt guard
- Tighten bolts -arrows- to 9 Nm.
Tightening torques on this page
19 torques
2.1.2 Assembly overview - toothed belt, PoloTo the drawing ↑

| Item | Part | Torque | Notes |
|---|---|---|---|
| 2 | + turn 90° further | 120 Nm | Renew · Use counterhold - 3415 - to loosen and tighten. · Do not additionally oil or grease the threads and shoulder · Turning further can be done in several stages. |
| 4 | 20 Nm | ||
| 6 | + turn 45° further | 20 Nm | Renew |
| 8 | + turn 45° further | 20 Nm | Renew |
| 10 | 15 Nm | ||
| 11 | 100 Nm | ||
| 14 | 20 Nm | ||
| 15 | 10 Nm | Renew | |
| 17 | + turn 90° further | 50 Nm | |
| 19 | 95 Nm | ||
| 21 | 20 Nm | Renew | |
| 23 | 15 Nm | ||
| 26 | 9 Nm | ||
| 27 | + turn 90° further | 10 Nm | Renew |
| 29 | 5 Nm | ||
| 31 | + turn 180° further | 40 Nm | Renew |
2.1.2 Assembly overview - toothed belt, PoloTo the steps ↑
| Step | Torque |
|---|---|
| Renew stud for idler pulley only if damaged. Specified torque for stud: 15 Nm. | 15 Nm |
| Renew stud for tensioning roller only if damaged. Specified torque for stud: 15 Nm. | 15 Nm |
| Tighten bolts -arrows- to 9 Nm. | 9 Nm |