1.6 TDI CR engine (EA189) · Cylinder head, valve gear · Cylinder head

Removing and installing cylinder head

⇒ 1.2.1 Removing and installing cylinder head, Polo

1.2.1 Removing and installing cylinder head, Polo

Removing and installing cylinder head: drawing 1

Special tools and workshop equipment required

  • Guide pin - 3070-
  • Diesel injection pump locking pin - 3359-
  • Crankshaft stop - T10050-
  • Counter-hold tool - T10051-
  • Puller - T10052-
  • Socket XZN 10 - T10385-
Removing and installing cylinder head: drawing 2
  • Torque wrench - V.A.G 1331-
  • Torque wrench - V.A.G 1332-
  • Drip tray for workshop hoist - VAS 6208-
  • Tool set - T100395-

Additional special tools required for Polo

Removing and installing cylinder head: drawing 3

Special tools and workshop equipment required

  • Support - 10-222 A-
  • Adapter - 10 - 222 A /8-
  • Hook - 10-222 A/10-
  • Shackle - 10-222 A/12-
Removing and installing cylinder head: drawing 4
  • Adapter - 10-222 A/18-

Continued for all vehicles

Removing

Polo

  • Remove windscreen wiper arms: ⇒ Electrical system; Rep. gr. 92; Windscreen wiper system; Removing and installing windscreen wiper arms.

Polo

  • Remove plenum chamber bulkhead ⇒ General body repairs, exterior; Rep. gr. 50; Plenum chamber bulkhead; Assembly overview - bulkhead.

Continued for all vehicles

  • Remove noise insulation:

    Polo ⇒ General body repairs, exterior; Rep. gr. 50; Noise insulation; Assembly overview - noise insulation

Removing and installing cylinder head: drawing 5
  • Pull vacuum line -1- off vacuum pump -2-.

Polo

Removing and installing cylinder head: drawing 6
  • Remove vacuum lines upwards from air filter -1- together with bracket.
  • Pull connector off charge pressure control solenoid valve - N75- -3-.
  • Unbolt charge pressure control solenoid valve - N75- with bracket at -2-.
  • Place charge pressure control solenoid valve - N75- with vacuum lines on engine.
  • Remove air filter housing together with air mass meter and intake hose ⇒ 7.2.2 Removing and installing air filter housing, Polo.
Removing and installing cylinder head: drawing 7

Pre-heater line -arrow 2- is not necessarily installed.

Removing and installing cylinder head: drawing 8
  • In order to ensure that vacuum hose -arrow 1- from brake servo to engine is not damaged, you must remove it ⇒ Brake systems; Rep. gr. 47; Brake servo/brake master cylinder; Assembly overview - brake servo/brake master cylinder.
  • Separate connectors.
Removing and installing cylinder head: drawing 9
  • -1- Exhaust gas temperature sender 1 - G 235-
  • -2- Exhaust gas temperature sender 3 - G 495-
  • -3- Exhaust gas temperature sender 4 - G 648-
  • -4- lambda probe - G 39-
Removing and installing cylinder head: drawing 10
  • Disconnect electrical connector -2- at pressure differential sender - G 505-.
  • Unscrew bolt -3- from pressure differential sender - G 505- bracket.
  • Lay pressure differential sender - G 505- aside to rear together with lines.

Remove fuel filter with bracket.

Removing and installing cylinder head: drawing 11
  • To do this, open quick-release couplings -A- and -B- of fuel lines.
  • Catch any escaping fuel.
Removing and installing cylinder head: drawing 12
  • Use a finger to release locking lug of fuel pre-heater valve.
  • Pull fuel pre-heater valve upwards out of coolant expansion tank guide.
Removing and installing cylinder head: drawing 13
  • Unclip fuel filter from lower part of fuel filter.
  • Remove fuel filter upwards.
  • Separate fuel supply line and return line at engine end.
  • Remove fuel filter and fuel lines together with fuel preheater valve.
  • Catch any escaping fuel.
  • Remove lower part of fuel filter ⇒ Rep. gr. 20; Fuel filter; Removing and installing fuel filter.
Removing and installing cylinder head: drawing 14
  • Filler neck: Unclip windscreen washer system reservoir -1-.
  • Filler neck: Unclip windscreen washer system reservoir -2-.

Continued for all vehicles

Removing and installing cylinder head: drawing 15
  • Unclip vacuum lines -arrow- and lay to side.
Removing and installing cylinder head: drawing 16
  • Pull off breather line -2-.
  • Lay vacuum lines to side.
Removing and installing cylinder head: drawing 17
  • Separate electrical connector -1- on oil pressure switch - F1-.
  • Unscrew bolt -arrow-.
Removing and installing cylinder head: drawing 18
  • Disconnect electrical connector -4- at coolant temperature sender - G62-.
Removing and installing cylinder head: drawing 19
  • Unclip engine pre-wiring harness from retainer -arrow-.

Vehicles with intake manifold flap motor - V157-.

Removing and installing cylinder head: drawing 20
  • Disconnect connector -3- from intake manifold flap motor - V157-.

Continued for all vehicles

  • Lay engine pre-wiring harness to one side.
Removing and installing cylinder head: drawing 21
  • Pull connectors off throttle valve module - J338- -2-.
  • Open clamp -3- and pull off charge air hose.
  • Remove bolt from oil dipstick attachment -4-.
Removing and installing cylinder head: drawing 22
  • Unscrew bolts -2, 5- and -arrows-.
  • Free electrical lines and hoses on left charge air pipe.
  • Loosen hose clip -3- and remove left charge air pipe.
Removing and installing cylinder head: drawing 23
  • Unscrew bolts -arrows- and remove pulsation damper -2-.
  • Carefully push charge air pipe to side as far as possible.

Loosen particulate filter.

to create space for removing and installing the oil supply line with turbocharger support.

Removing and installing cylinder head: drawing 24
  • Remove securing clamp -1- between particulate filter and turbocharger.
Removing and installing cylinder head: drawing 25
  • Unscrew bolt -1-.
Removing and installing cylinder head: drawing 26
  • Unscrew nuts -2-.
Removing and installing cylinder head: drawing 27
  • Now you can access the securing bolt on the retaining clamp -arrow- for the oil return line on the turbocharger support. Unscrew bolt -arrow-.
Removing and installing cylinder head: drawing 28
  • Remove connecting pipes -A- to exhaust gas recirculation cooler.

Polo

Continued for all vehicles

Removing and installing cylinder head: drawing 29
  • Remove coolant hoses from connections, loosen hose clips -1- and -2- for this.
Removing and installing cylinder head: drawing 30
  • Separate connector of Hall sender - G40- -1-.
  • Unscrew securing nut of toothed belt tensioning roller.

Set up support bracket - 10 - 222 A- with necessary adapters and support engine in installation position ⇒ 2.2 Supporting engine in installation position.

Removing and installing cylinder head: drawing 31

Continued for all vehicles

  • Detach camshaft pulley from hub.
  • Remove camshaft hub; pull off camshaft hub using puller - T10052-.
Removing and installing cylinder head: drawing 32
  • Counterhold hub with counterhold - T10051- and loosen securing bolt -1- of hub.
  • Loosen hub securing bolt about 2 turns.
Removing and installing cylinder head: drawing 33
  • Fit puller - T10052- and align it with holes in hub.
  • Tighten securing bolts -1-.
  • Apply tension to hub by evenly tightening puller -2- until hub separates from taper of camshaft.
  • Remove hub from taper of camshaft.
Removing and installing cylinder head: drawing 34
Removing and installing cylinder head: drawing 35
  • Unscrew Hall sender - G40- -arrow-.
Removing and installing cylinder head: drawing 36
  • Maintain sequence when loosening cylinder head bolts.
  • First lift cylinder head on gearbox side and guide it out of toothed belt guard. Make sure that toothed belt tensioner does not fall down.

Installing

Install in reverse order, noting the following:

Removing and installing cylinder head: drawing 37
  • Only remove sealant residue from cylinder head and cylinder block using scraper - VAS 852 005- or a commercially available ceramic glass scraper.
  • The sealing surfaces must not be damaged.
  • There must be no oil or coolant in the bolt pockets.
  • Do not remove new cylinder head gasket from packaging until it is ready to be fitted.
  • If a new cylinder head is installed, contact surfaces between roller rocker fingers and running surface of cam must be oiled.
  • Handle the cylinder head gasket very carefully to prevent damage to the silicone coating or the indented area of the gasket.
  • Turn the crankshaft carefully at least 2 rotations to ensure that none of the valves make contact when the starter is operated.
  • When the cylinder head or cylinder head gasket is renewed, the entire coolant and the engine oil must be changed.
  • Remove any loose remains using a lint-free cloth.
  • Before fitting cylinder head, remove crankshaft stop - T10050-, and turn crankshaft in opposite direction of engine rotation until all pistons are nearly uniformly below TDC.
Removing and installing cylinder head: drawing 38
  • Note cylinder head gasket identification:
  • 1 Part number
  • 2 Holes
  • 3 Ignore
  • Cylinder head gasket must lie with identification facing upwards.
Removing and installing cylinder head: drawing 39
  • To centre, screw guide pins -3070/9- into outer threaded holes on intake side.
  • Fit cylinder head.
  • Insert 8 cylinder head bolts and screw in by hand until contact is made.
  • Unscrew guide pins -3070/9- through bolt holes in cylinder head and screw remaining cylinder head bolts by hand until contact is made.
Removing and installing cylinder head: drawing 40
  • Tighten cylinder head in 4 stages in sequence shown as follows:
  • 1 Tighten initially with torque wrench:

Stage I = 35 Nm

Step II = 60 Nm

  • 2 Turn further with rigid spanner:

Stage III = turn 90° further.

Stage IV = turn 90° further.

Removing and installing cylinder head: drawing 41
  • Re-fit Hall sender - G40- -arrow-.

Polo

  • Secure rear toothed belt guard -arrow- on cylinder head after supporting it.

Continued for all vehicles

  • Install hub and camshaft pulley.
  • Lock camshaft and high-pressure pump with diesel injection pump locking pin - 3359-
Removing and installing cylinder head: drawing 42
  • Now rotate crankshaft in direction of rotation to TDC and lock crankshaft using crankshaft stop - T10050-.

Continue installation in reverse order of removal. During this procedure, observe the following:

Polo

Support engine again ⇒ 1.8.4 Removing and installing engine bracket, Polo.

Continued for all vehicles

After any work on the fuel system

Connect a diagnostic tester.

Perform the function “Filling/bleeding high pressure pump/fuel system” in “Guided functions” ⇒ 1.3 Filling/bleeding fuel system.

  • Carry out road test and read all event memories.

Tightening torques on this page

2 torques

1.2.1 Removing and installing cylinder head, PoloTo the steps ↑

StepTorque
Stage I = 35 Nm35 Nm
Step II = 60 Nm60 Nm

All tightening torques in this manual →