1.4 TSI engine (EA111) · VW Polo 6R
Tightening torques
Every tightening torque the 1.4 TSI engine (EA111) manual gives for the VW Polo 6R, by repair group and procedure. Each one links to its drawing or table in the procedure.
- 200 torques
- 57 procedures
10 – Removing and installing engine
Removing engine (Polo)
In the steps
| Step | Torque |
|---|---|
| Torque wrench (40 … 200 Nm) - V.A.G. 1332- | 200 Nm |
| Tighten all bolts on engine support - T10416- to 20 Nm. | 20 Nm |
Assembly overview – assembly mountings (Polo)
In the steps
| Step | Torque |
|---|---|
| A = 20 Nm + turn 90° further | 20 Nm |
| B = 30 Nm + turn 90° further | 30 Nm |
| A = 40 Nm + turn 90° further | 40 Nm |
| B = 50 Nm + turn 90° further | 50 Nm |
| C = 50 Nm + turn 90° further | 50 Nm |
| A = 30 Nm + turn 90° further | 30 Nm |
| B = 40 Nm + turn 90° further | 40 Nm |
13 – Crankshaft group
Assembly overview – poly V-belt drive
| Item | Part | Torque | Notes |
|---|---|---|---|
| 1 | + 1/4 turn (90°) further | 40 Nm | To loosen and tighten securing bolt, counterhold supercharger shaft with 16 mm spanner. · Renew |
| 3 | 23 Nm | ||
| 5 | 8 Nm | ||
| 7 | 23 Nm | ||
| 9 | 23 Nm | ||
| 13 | + 1/4 turn (90°) further | 40 Nm | Removing and installing with vehicle raised · Renew |
| 15 | 23 Nm |
In the steps
| Step | Torque |
|---|---|
| Specified torque for securing bolt: 40 Nm. | 40 Nm |
Assembly overview – cylinder block, belt pulley end
| Item | Part | Torque | Notes |
|---|---|---|---|
| 6 | + 1/4 turn (90°) further | 20 Nm | Renew |
| 9 | 25 Nm | ||
| 10 | Locating pin for chain tensioner | 8 Nm | Specified torque |
| 11 | Chain tensioner with tensioning rail | 8 Nm | For oil pump drive. · Specified torque |
| 14 | 13 Nm | ||
| 18 | 9 Nm | ||
| 20 | 10 Nm | ||
| 25 | 50 Nm | ||
| 27 | + 1/4 turn (90°) further | 40 Nm | Lock sprockets using counterhold - T10172-. · Bolt with left-hand thread. · Renew |
| 28 | + 1/4 turn (90°) further | 50 Nm | Renew |
| 34 | Guide pin | 20 Nm | Specified torque |
Removing and installing bracket for ancillaries
In the steps
| Step | Torque |
|---|---|
| Tighten securing bolts -1- to 25 Nm. | 25 Nm |
Removing and installing crankshaft pulley
In the steps
| Step | Torque |
|---|---|
| Tighten locking pin - T10340- to 30 Nm. | 30 Nm |
| Specified torque: 150 Nm + 1/2 turn (180°) further. | 150 Nm |
| Specified torque: 30 Nm | 30 Nm |
Assembly overview – cylinder block, gearbox end
All except 11:Renew
| Item | Part | Torque | Notes |
|---|---|---|---|
| 7 | + 1/4 turn (90°) further | 60 Nm | |
| 10 | 12 Nm | ||
| 11 | Sealing flange with sender wheel and oil seal | 5 Nm | Specified torque for engine speed sender - G28- : . · Renew sealing flange complete with oil seal and sender wheel only. |
Removing and installing sealing flange on gearbox side
2.2.6 D - Pressing sender wheel onto crankshaft flange using assembly tool - T10134-To the steps →
| Step | Torque |
|---|---|
| Tighten hexagon nut of assembly tool - T10134- to 35 Nm using torque wrench - V.A.G 1331- and tool insert 24 mm - V.A.G 1332/11-. | 35 Nm |
| After hexagon nut is tightened to 35 Nm, a small air gap must still be present between cylinder block and sealing flange. | 35 Nm |
2.2.7 E - Checking sender wheel installation position on crankshaftTo the steps →
| Step | Torque |
|---|---|
| Tighten new securing bolts for sealing flange to 15 Nm using alternate and diagonal sequence. | 15 Nm |
| Install engine speed sender - G28- -arrow- and tighten securing bolt to 5 Nm. | 5 Nm |
| Install flywheel using new bolts. Tighten securing bolts to 60 Nm +1/4 turn (90°). | 60 Nm |
2.2.8 f) Re-pressing sender wheelTo the steps →
| Step | Torque |
|---|---|
| Tighten hexagon nut of assembly tool - T10134- to 40 Nm using torque wrench - V.A.G 1331- and tool insert 24 mm - V.A.G 1332/11-. | 40 Nm |
| Tighten hexagon nut for assembly tool - T10134- to 45 Nm. | 45 Nm |
Assembly overview – crankshaft
| Item | Part | Torque | Notes |
|---|---|---|---|
| 1 | + 1/4 turn (90°) further | 50 Nm | Only tighten to 50 Nm when measuring crankshaft radial clearance. Do not turn further. |
| 4 | Sealing flange with sender wheel and oil seal | 5 Nm | With engine speed sender - G28- (not illustrated). · Specified torque for engine speed sender - G28- : . · Renew sealing flange complete with oil seal and sender wheel only. |
| 5 | 12 Nm | Renew |
Assembly overview – pistons and conrods
| Item | Part | Torque | Notes |
|---|---|---|---|
| 6 | Conrod bolt | 20 Nm | M7×0.75: + 1/4 turn (90°) further. · M8×1: 30 Nm + 1/4 turn (90°) further. · Renew · Oil threads and contact surface · To measure radial clearance, tighten to corresponding specified torque but not further. |
| 9 | 27 Nm | Opening pressure of pressure relief valve: 1.8…2.2 bar |
Removing and installing oil spray jets
| Item | Part | Torque |
|---|---|---|
| 1 | Pressure relief valve - | 27 Nm |
15 – Cylinder head, valve gear
Assembly overview – cylinder head
| Item | Part | Torque | Notes |
|---|---|---|---|
| 1 | 20 Nm | ||
| 3 | Wiring guide | 8 Nm | Bolt to camshaft housing with torque. |
| 5 | 10 Nm | ||
| 7 | Stud | 6 Nm | |
| 8 | + 1/4 turn (90°) further | 10 Nm | Renew · Tighten from inside outwards. |
| 10 | 20 Nm | ||
| 13 | Oil pressure switch - F1- | 20 Nm | If seal is leaking, nip open and renew. |
| 16 | Guide pin | 20 Nm | Specified torque |
Removing and installing camshaft housing
1.2.2 InstallingTo the steps →
| Step | Torque |
|---|---|
| Ensure that camshaft housing is not canted. Specified torque 10 Nm + 1/4 turn (90°) further. | 10 Nm |
1.2.2 InstallingTo the table →
| Part | Torque |
|---|---|
| Oil pressure switch - F1- | 20 Nm |
Removing and installing cylinder head
1.3.2 InstallingTo the table →
| Part | Torque |
|---|---|
| 1 | 30 Nm |
Checking compression
In the steps
| Step | Torque |
|---|---|
| Insert spark plugs using spark plug socket - 3122 B- and tighten to 25 Nm. | 25 Nm |
Assembly overview – valve gear
All except 6, 9:Renew
| Item | Part | Torque | Notes |
|---|---|---|---|
| 1 | + 1/4 turn (90°) further | 40 Nm | Left-hand thread |
| 6 | 10 Nm | ||
| 7 | + 1/4 turn (90°) further | 10 Nm | Tighten from inside outwards. |
| 9 | 10 Nm | ||
| 22 | + 1/4 turn (90°) further | 50 Nm |
Removing and installing valve timing housing (Eos, Golf Plus, Scirocco, Golf, Polo, Sharan, Golf Cabriolet)
3.1.2 InstallingTo the steps →
| Step | Torque |
|---|---|
| M6 bolt to 10 Nm | 10 Nm |
| M10 bolt to 50 Nm | 50 Nm |
Checking valve timing
| Part | Torque |
|---|---|
| Oil pressure switch - F1- | 20 Nm |
Adjusting valve timing
In the steps
| Step | Torque |
|---|---|
| Renew bolts -2- and -4-. Tighten bolt -2- to 40 Nm and bolt -4- to 50 Nm (use counterhold - T10172- ). | 40 Nm / 50 Nm |
| Tighten locking pin - T10340- to 30 Nm. | 30 Nm |
| Hold camshaft sprockets -1- and -5- in this position with counterhold - T10172- and tighten bolt -2- (left-hand thread) to 40 Nm and bolt -4- to 50 Nm. | 40 Nm / 50 Nm |
| Tighten locking pin - T10340- to 30 Nm. | 30 Nm |
| Part | Torque |
|---|---|
| Oil pressure switch - F1- | 20 Nm |
Checking timing chain
In the steps
| Step | Torque |
|---|---|
| Push torque wrench - VAS 6583- clockwise and maintain a torque of 40 Nm on it. | 40 Nm |
| Maintain a torque of 40 Nm on torque wrench - VAS 6583-. | 40 Nm |
Removing and installing timing chain and chain drive for oil pump
In the steps
| Step | Torque |
|---|---|
| Tighten new securing bolt -1- to 20 Nm + 1/4 turn (90°) further. | 20 Nm |
| Position chain tensioner on oil pump drive chain and tighten securing bolt -3- to 8 Nm. | 8 Nm |
| Install chain tensioner -1- and tighten securing bolts -2- to 9 Nm. | 9 Nm |
| Tighten securing bolt -2- to 40 Nm and bolt -4- to 50 Nm (use counterhold -T10172- ). | 40 Nm / 50 Nm |
| Part | Torque |
|---|---|
| Oil pressure switch - F1- | 20 Nm |
17 – Lubrication
Assembly overview – sump, oil pump
| Item | Part | Torque | Notes |
|---|---|---|---|
| 4 | Coolant pipe | 20 Nm | For engine oil cooler · Specified torque, bracket to crankcase: . |
| 5 | 8 Nm | ||
| 8 | Oil filter | 20 Nm | Loosen with oil filter tool - 3417-. · Observe fitting instructions on oil filter · With non-return valve |
| 10 | 10 Nm | ||
| 17 | + 1/4 turn (90°) further | 20 Nm | Renew |
| 20 | 10 Nm | ||
| 22 | Oil drain plug | 30 Nm | With captive seal · Renew |
| 23 | 13 Nm | Loosen and tighten flywheel end bolts only with long-reach Allen key - T10058-. | |
| 24 | 40 Nm | ||
| 26 | + 1/4 turn (90°) further | 14 Nm | |
| 28 | + 1/4 turn (90°) further | 2 Nm |
In the steps
| Step | Torque |
|---|---|
| Specified torque oil suction pipe: 9 Nm | 9 Nm |
Removing and installing sump
In the steps
| Step | Torque |
|---|---|
| Tighten oil sump bolts to 13 Nm. | 13 Nm |
| Specified torque for oil pan securing bolts to gearbox: 40 Nm | 40 Nm |
Removing and installing oil pump
In the steps
| Step | Torque |
|---|---|
| Install oil pump and tighten securing bolts to 14 Nm + 1/4 turn (90°) further. | 14 Nm |
| Specified torque oil suction pipe: 9 Nm | 9 Nm |
| Tighten securing bolt to 20 Nm +1/4 turn (90°) further. | 20 Nm |
Checking oil pressure and oil pressure switch
In the steps
| Step | Torque |
|---|---|
| Specified torque for oil pressure switch: 20 Nm | 20 Nm |
19 – Cooling
Assembly overview – thermostat
| Item | Part | Torque | Notes |
|---|---|---|---|
| 8 | Thermostat housing | 10 Nm | Specified torque |
| 15 | 5 Nm |
Removing and installing coolant pump (Polo, Touran, Golf Plus, Eos, Tiguan, Scirocco, Golf, Golf Cabriolet)
In the steps
| Step | Torque |
|---|---|
| Tighten securing bolts to 8 Nm. | 8 Nm |
| The screw-type clips on the charge air pipes must be tightened to 5.5 Nm. If the torque is too low or too high, the charge air hose may slip off the charge air pipe during vehicle operation. | 5.5 Nm |
Removing and installing coolant pump belt pulley (Polo, Touran, Golf Plus, Eos, Tiguan, Scirocco, Golf, Golf Cabriolet)
In the steps
| Step | Torque |
|---|---|
| Tighten securing bolts to 24 Nm. | 24 Nm |
Removing and installing coolant circulation pump V50 (Polo, Touran, Golf Plus, Eos, Tiguan, Scirocco, Golf, Golf Cabriolet)
In the steps
| Step | Torque |
|---|---|
| Specified torque for securing bolt: 10 Nm. | 10 Nm |
Assembly overview – radiator/radiator fan (Polo)
| Item | Part | Torque |
|---|---|---|
| 7 | 5 Nm | |
| 12 | 5 Nm |
Removing and installing radiator with charge air cooler (Polo)
In the steps
| Step | Torque |
|---|---|
| The screw-type clips on the charge air pipes must be tightened to 5.5 Nm. If the torque is too low or too high, the charge air hose may slip off the charge air pipe during vehicle operation. | 5.5 Nm |
| Torque wrench (5 … 50 Nm) - V.A.G 1331- | 50 Nm |
21 – Turbocharging/supercharging
Assembly overview – turbocharger
| Item | Part | Torque |
|---|---|---|
| 2 | 10 Nm | |
| 3 | 7 Nm |
| Item | Part | Torque | Notes |
|---|---|---|---|
| 1 | 8 Nm | ||
| 4 | Exhaust turbocharger | 20 Nm | Specified torque for catalytic converter studs |
| 8 | 25 Nm | Renew studs and fastening nuts. | |
| 11 | 8 Nm | ||
| 14 | Banjo bolt | 20 Nm | Secured to valve timing housing. |
| 16 | Banjo bolt | 30 Nm |
Removing and installing turbocharger
In the steps
| Step | Torque |
|---|---|
| The screw-type clips on the charge air pipes must be tightened to 5.5 Nm. If the torque is too low or too high, the charge air hose may slip off the charge air pipe during vehicle operation. | 5.5 Nm |
Removing and installing vacuum unit for turbocharger
In the steps
| Step | Torque |
|---|---|
| Specified torque for vacuum unit to turbocharger: 10 Nm | 10 Nm |
Adjusting vacuum unit for turbocharger
In the steps
| Step | Torque |
|---|---|
| If the result (mean value) is 5.5 +/- 0.25 mm, tighten the lock nut to 9 Nm and secure with sealing paint. | 9 Nm |
| The screw-type clips on the charge air pipes must be tightened to 5.5 Nm. If the torque is too low or too high, the charge air hose may slip off the charge air pipe during vehicle operation. | 5.5 Nm |
Assembly overview – supercharger
| Item | Part | Torque | Notes |
|---|---|---|---|
| 4 | 7 Nm | Self-tapping bolt · Securing bolt must only be tightened with a nut runner if nut runner speed is max. 500 rpm and a max. specified torque of 7 Nm is set. | |
| 5 | 7 Nm | ||
| 6 | 7 Nm | Self-tapping bolt · Securing bolt must only be tightened with a nut runner if nut runner speed is max. 500 rpm and a max. specified torque of 7 Nm is set. | |
| 13 | 8 Nm | ||
| 16 | 23 Nm | ||
| 18 | + 1/4 turn (90°) further | 40 Nm | To loosen and tighten securing bolt, counterhold supercharger shaft with spanner. · Renew |
| 20 | 25 Nm |
Removing and installing supercharger
In the steps
| Step | Torque |
|---|---|
| Torque wrench (5 to 50 Nm) - V.A.G 1331- | 50 Nm |
| Specified torque: 25 Nm | 25 Nm |
| Specified torque for new securing bolt -2-: 40 Nm + 1/4 turn (90°) further. | 40 Nm |
| Tighten bolts -arrows- to 23 Nm. | 23 Nm |
| The screw-type clips on the charge air pipes must be tightened to 5.5 Nm. If the torque is too low or too high, the charge air hose may slip off the charge air pipe during vehicle operation. | 5.5 Nm |
Removing and installing drive unit seal for supercharger
In the steps
| Step | Torque |
|---|---|
| Tighten the new securing bolts for the drive unit to “12 Nm” according to the specified sequence -A- to -H-. | 12 Nm |
Charge air system
In the steps
| Step | Torque |
|---|---|
| The screw-type clips on the charge air pipes must be tightened to 5.5 Nm. If the torque is too low or too high, the charge air hose may slip off the charge air pipe during vehicle operation. | 5.5 Nm |
Assembly overview – charge air system (Polo)
In the steps
| Step | Torque |
|---|---|
| The screw-type clips on the charge air pipes must be tightened to 5.5 Nm. If the torque is too low or too high, the charge air hose may slip off the charge air pipe during vehicle operation. | 5.5 Nm |
| Item | Part | Torque |
|---|---|---|
| 2 | Hose clip | 5.5 Nm |
| 6 | 7 Nm | |
| 9 | 10 Nm | |
| 10 | 5 Nm | |
| 12 | 10 Nm | |
| 13 | 10 Nm | |
| 16 | 10 Nm |
Fitting hose connections with plug-in connectors
In the steps
| Step | Torque |
|---|---|
| The screw-type clips on the charge air pipes must be tightened to 5.5 Nm. If the torque is too low or too high, the charge air hose may slip off the charge air pipe during vehicle operation. | 5.5 Nm |
24 – Mixture preparation – injection
Air filter
1.1 Assembly overview - air filterTo the drawing →
| Item | Part | Torque | Notes |
|---|---|---|---|
| 1 | 1.6 Nm | ||
| 8 | Air filter lower part | 8 Nm | With captive securing bolt. · Specified torque · With intake connection. |
1.2 Assembly overview - air filter (Polo)To the drawing →
| Item | Part | Torque | Notes |
|---|---|---|---|
| 4 | 1.6 Nm | Tighten with torque screwdriver - VAS 6494-. | |
| 9 | 8 Nm | ||
| 15 | Intake air duct | 3 Nm |
1.3 Removing and installing air filter housingTo the steps →
| Step | Torque |
|---|---|
| Tighten new securing bolt -2- to 8 Nm and slide spring-type clip -1- with intake hose onto air filter connection. | 8 Nm |
Assembly overview – intake manifold
| Item | Part | Torque | Notes |
|---|---|---|---|
| 2 | 3 Nm | ||
| 3 | 7 Nm | Self-tapping bolt · The securing bolt may only be tightened using an impact wrench if the wrench speed is max. 500 rpm and a max. specified torque of 7 Nm is set. | |
| 7 | 7 Nm | Self-tapping bolt · The securing bolt may only be tightened using an impact wrench if the wrench speed is max. 500 rpm and a max. specified torque of 7 Nm is set. | |
| 10 | 7 Nm | Self-tapping bolt · The securing bolt may only be tightened using an impact wrench if the wrench speed is max. 500 rpm and a max. specified torque of 7 Nm is set. | |
| 11 | 3 Nm | ||
| 15 | 20 Nm | ||
| 16 | Fuel pressure sender - G247- | 22 Nm | |
| 17 | 80 Nm | ||
| 20 | 20 Nm | ||
| 22 | 7 Nm | ||
| 25 | 7 Nm |
| Item | Part | Torque | Notes |
|---|---|---|---|
| 10 | 8 Nm | ||
| 11 | Fuel line | 18 Nm | High pressure · Specified torque for union nuts: . |
| 14 | Non-return valve | 10 Nm | For crankcase ventilation. · Specified torque |
| 20 | 5 Nm | ||
| 26 | Union | 10 Nm | For crankcase ventilation. · Connected to valve timing housing. · Specified torque |
Removing and installing injectors
In the steps
| Step | Torque |
|---|---|
| Place lower part of intake manifold carefully on injectors and tighten securing bolts to 20 Nm ⇒ 2.1 Assembly overview - intake manifold. | 20 Nm |
Renewing seals on injectors
In the steps
| Step | Torque |
|---|---|
| Place lower part of intake manifold carefully on injectors and tighten securing bolts to 20 Nm ⇒ 2.1 Assembly overview - intake manifold. | 20 Nm |
Checking fuel pressure sender
In the steps
| Step | Torque |
|---|---|
| Instead of fuel pressure sender - G247-, screw in adapter - VAS 6394/2- and tighten to 22 Nm. | 22 Nm |
| Open cover -2- of digital pressure gauge - VAS 6394/1- and tighten fuel pressure sender - G247- to digital pressure gauge to 22 Nm. | 22 Nm |
Actuator for structure-borne sound R214 and control unit for structureborne sound J869 (Polo, left-hand drive)
| Item | Part | Torque |
|---|---|---|
| 1 | 8 Nm | |
| 2 | 8 Nm |
Assembly overview – actuator for structure-borne sound R214 and control unit for structure-borne sound J869 (Polo, right-hand drive)
| Item | Part | Torque |
|---|---|---|
| 4 | 8 Nm | |
| 8 | 8 Nm |
Assembly overview – high-pressure pump
| Item | Part | Torque | Notes |
|---|---|---|---|
| 4 | 20 Nm | Tighten bolts evenly. | |
| 6 | Union nut | 18 Nm | Counterhold when loosening connection to high-pressure pump. |
Removing and installing high-pressure pump
In the steps
| Step | Torque |
|---|---|
| Specified torque: 20 Nm | 20 Nm |
| Specified torque of wiring guide securing bolt: 8 Nm | 8 Nm |
| Tighten union nut -1- of high-pressure line to 18 Nm. | 18 Nm |
| Tighten union nut -3- of high-pressure line to 18 Nm. | 18 Nm |
26 – Exhaust system
Assembly overview – silencers (Polo)
| Item | Part | Torque |
|---|---|---|
| 4 | 25 Nm | |
| 6 | 25 Nm | |
| 7 | 25 Nm |
Installation position of clamp
In the steps
| Step | Torque |
|---|---|
| Specified torque: 25 Nm | 25 Nm |
| Specified torque: 35 Nm | 35 Nm |
Exhaust gas cleaning
2.3 Assembly overview - exhaust gas treatment (Polo)To the drawing →
| Item | Part | Torque | Notes |
|---|---|---|---|
| 2 | 10 Nm | ||
| 5 | 25 Nm | Renew studs and fastening nuts. | |
| 9 | Lambda probe - G39- | 50 Nm | Grease only the threads with “G 052 112 A3”; “G 052 112 A3” cannot get into the slots on the probe body. · Remove and install using ring spanner for Lambda probe - 3337- |
| 10 | 25 Nm | ||
| 12 | 10 Nm | ||
| 14 | 23 Nm | Renew | |
| 15 | Lambda probe after catalytic converter - G130- | 50 Nm | Specified torque · Grease only the threads with “G 052 112 A3”; “G 052 112 A3” cannot get into the slots on the probe body. |
| 16 | 10 Nm |
28 – Ignition system
Assembly overview – ignition system
| Item | Part | Torque | Notes |
|---|---|---|---|
| 5 | 20 Nm | The specified torque influences the function of the knock sensor. | |
| 9 | 10 Nm | ||
| 10 | Spark plug | 25 Nm | Remove and install with spark plug socket and extension - 3122 B- |
| 11 | Wiring guide | 5 Nm | Bolt to camshaft housing with torque. |
| 13 | 10 Nm | Loosen or tighten only with ignition switched off. |
Removing and installing ignition coils with output stage
In the steps
| Step | Torque |
|---|---|
| Specified torques of securing bolts for crankcase breather connection and for non-return valve: 10 Nm | 10 Nm |
Removing and installing engine speed sender G28
In the steps
| Step | Torque |
|---|---|
| Install engine speed sender - G28- and tighten securing bolt to 5 Nm. | 5 Nm |
Test data, spark plugs
| Part | Torque |
|---|---|
| Specified torque | 25 Nm |