1.4 TSI engine (EA111) · Cylinder head, valve gear · Cover for timing chain

Removing and installing valve timing housing (Eos, Golf Plus, Scirocco, Golf, Polo, Sharan, Golf Cabriolet)

Removing and installing valve timing housing (Eos, Golf Plus, Scirocco, Golf, Polo, Sharan, Golf Cabriolet): drawing 1

Special tools and workshop equipment required

  • Support - 10-222A-
  • Adapter - 10 - 222 A /8-
  • Counter-hold tool - 3415-
  • Pin - 3415/1-
  • Torque wrench - V.A.G 1331-
Removing and installing valve timing housing (Eos, Golf Plus, Scirocco, Golf, Polo, Sharan, Golf Cabriolet): drawing 2
  • Torque wrench - V.A.G 1332-
  • Silicone adhesive sealant - D 176 501 A1-

3.1.1 Removing

Removing and installing valve timing housing (Eos, Golf Plus, Scirocco, Golf, Polo, Sharan, Golf Cabriolet): drawing 3

Scirocco

Removing and installing valve timing housing (Eos, Golf Plus, Scirocco, Golf, Polo, Sharan, Golf Cabriolet): drawing 4
  • Install support device - 10 - 222 A- with adapter - 10 - 222 A /8- as shown and hook into lifting eye.
  • Position adapter - 10 - 222 A /8- on vehicle front end -arrows- as shown.

All vehicles

Removing and installing valve timing housing (Eos, Golf Plus, Scirocco, Golf, Polo, Sharan, Golf Cabriolet): drawing 5
  • Install support device - 10 - 222 A- with adapter - 10 - 222 A /8- as shown and hook into lifting eye.
Removing and installing valve timing housing (Eos, Golf Plus, Scirocco, Golf, Polo, Sharan, Golf Cabriolet): drawing 6
Removing and installing valve timing housing (Eos, Golf Plus, Scirocco, Golf, Polo, Sharan, Golf Cabriolet): drawing 7
  • Now remove pulley securing bolt. Hold pulley with counterhold - 3415- and -3415/1-.
Removing and installing valve timing housing (Eos, Golf Plus, Scirocco, Golf, Polo, Sharan, Golf Cabriolet): drawing 8
  • Remove Allen head bolts for valve timing housing and hexagon bolts indicated by -arrows-.
  • Remove valve timing housing.

3.1.2 Installing

Removing and installing valve timing housing (Eos, Golf Plus, Scirocco, Golf, Polo, Sharan, Golf Cabriolet): drawing 9
  • Clean sealing surfaces carefully. They must be free of oil and grease.
  • 1 Securing bolt
  • 2 Crankshaft belt pulley
  • 3 Diamond coated washer (clipped onto crankshaft belt pulley)
  • 4 Crankshaft oil seal
  • 5 Bearing bush
  • 6 O-ring
  • 7 Diamond coated washer
Removing and installing valve timing housing (Eos, Golf Plus, Scirocco, Golf, Polo, Sharan, Golf Cabriolet): drawing 10
  • Apply silicone adhesive sealant - D 176 501 A1- to joints between camshaft housing and cylinder head -1- and between cylinder head and cylinder block -2-.
  • Fit new gasket onto dowel pins.
  • When fitting, install two -M6x80- studs into cylinder head and cylinder block as a guide.
  • Fit valve timing housing with crankshaft bearing bush simultaneously onto studs, dowel pins and crankshaft journal.
  • Tighten valve timing housing securing bolts evenly and diagonally.

Ensure that valve timing housing is not canted.

Specified torque:

M6 bolt to 10 Nm

M10 bolt to 50 Nm

Eos, Golf Plus, Scirocco, Golf, Golf Cabriolet, Sharan

Align engine mountings as follows:

Removing and installing valve timing housing (Eos, Golf Plus, Scirocco, Golf, Polo, Sharan, Golf Cabriolet): drawing 11
  • There must be a distance -a- of at least 10 mm between engine support and longitudinal member (right side).
  • The side surface of the engine support -2- should be located parallel to the support arm -1-.

Polo

  • Rock engine to align engine mountings stress-free.

Install crankshaft belt pulley ⇒ 1.7 Removing and installing crankshaft pulley.

Further assembly is basically a reverse of the dismantling sequence.

Tightening torques on this page

2 torques

3.1.2 InstallingTo the steps ↑

StepTorque
M6 bolt to 10 Nm10 Nm
M10 bolt to 50 Nm50 Nm

All tightening torques in this manual →