1.4 TSI engine (EA111) · Cylinder head, valve gear · Chain drive

Removing and installing timing chain and chain drive for oil pump

Removing and installing timing chain and chain drive for oil pump: drawing 1

Special tools and workshop equipment required

Removing and installing timing chain and chain drive for oil pump: drawing 2
Removing and installing timing chain and chain drive for oil pump: drawing 3
  • Spark plug socket - 3122 B-
  • Counter-hold tool - 3415-
  • Torque wrench - V.A.G 1331-

Removing

Removing and installing timing chain and chain drive for oil pump: drawing 4
  • Lift engine cover panel at points -1- and pull it forwards in direction of -arrow-.
  • Remove air filter (Golf, Golf Plus, Eos, Scirocco, Touran, Tiguan, Sharan, Passat, Passat CC, Golf Cabriolet) ⇒ 1.3 Removing and installing air filter housing.
  • Drain coolant (Golf, Golf Plus, Eos, Scirocco, Touran, Tiguan, Golf Cabriolet).
  • Drain coolant (Sharan).
  • Drain coolant (Passat, Passat CC).
Removing and installing timing chain and chain drive for oil pump: drawing 5
Removing and installing timing chain and chain drive for oil pump: drawing 6
  • Release connector -2- and pull off.
  • Remove oil pressure switch - F1- -1-.
  • Then remove bolts for both camshaft covers -3-.
Removing and installing timing chain and chain drive for oil pump: drawing 7
  • Unclip engine pre-wiring harness -1-.
  • Pull coolant pipe -2- and engine pre-wiring harness -1- away from cylinder head.
  • Remove both bolts -3- from cylinder head.
Removing and installing timing chain and chain drive for oil pump: drawing 8
  • Screw dial gauge adapter - T10170- into spark plug hole to stop.
  • Insert dial gauge - VAS 6079- as far as stop and lock it in position with lock nut -arrow-.
  • Turn crankshaft in direction of engine rotation, to TDC No. 1 cylinder. Note position of small needle on dial gauge.
Removing and installing timing chain and chain drive for oil pump: drawing 9

The bores -arrows- in the camshafts must be as illustrated. If necessary, turn crankshaft one turn (360°) further.

If this is not the case, the camshaft clamp is defective and must be renewed.

Do not use any kind of hammer to position the camshaft clamp.

Removing and installing timing chain and chain drive for oil pump: drawing 10
  • Insert camshaft clamp - T10171 A- to stop in camshaft openings.

Locking pins -arrows 1- must engage in holes -arrows 2-. Inscription “TOP” -arrow 3- must be readable from above.

Removing and installing timing chain and chain drive for oil pump: drawing 11
  • Screw an M6 bolt hand-tight into corresponding bore -arrows- (but do not tighten) to secure camshaft clamp - T10171 A-.

Remove valve timing housing (Eos, Golf Plus, Scirocco, Golf, Polo, Sharan, Golf Cabriolet) ⇒ 3.1 Removing and installing valve timing housing (Eos, Golf Plus, Scirocco, Golf, Polo, Sharan, Golf Cabriolet).

Remove valve timing housing (Tiguan, Touran).

Remove valve timing housing (Passat, Passat CC)

Removing and installing timing chain and chain drive for oil pump: drawing 12
  • Pull cover -1- off sprocket for oil pump.
Removing and installing timing chain and chain drive for oil pump: drawing 13
  • Press tensioning rail in -direction of arrow- by hand and lock piston of chain tensioner with locking pin - T40011-.
Removing and installing timing chain and chain drive for oil pump: drawing 14
  • Mark direction of rotation of timing chain -3- using coloured felt tip marker pen.
  • Remove bolts -2- and -4- and remove camshaft adjuster -1- with timing chain -3-. Counterhold using counterhold - T10172-.
Removing and installing timing chain and chain drive for oil pump: drawing 15
  • Hold oil pump sprocket with counterhold - T10172- and loosen securing bolt -1-.
Removing and installing timing chain and chain drive for oil pump: drawing 16
  • Use a screwdriver on bolt -2- to release tensioning spring -1- then remove tensioning spring -1-.
  • Unscrew securing bolt -3- and remove chain tensioner.
  • Mark direction of rotation of oil pump drive chain -2- using felttip marker.
Removing and installing timing chain and chain drive for oil pump: drawing 17
  • Unscrew securing bolt for sprocket -1- and remove sprockets -1- and -3- together with drive chain for oil pump -2-.

Installing

  • The crankshaft must be positioned at TDC No. 1 cylinder.
Removing and installing timing chain and chain drive for oil pump: drawing 18
  • Push sprocket -1- in -direction of arrow- onto crankshaft journal as far as the stop.
Removing and installing timing chain and chain drive for oil pump: drawing 19
  • Mark position of sprocket and crankshaft to cylinder block using a felt-tip marker.
Removing and installing timing chain and chain drive for oil pump: drawing 20
  • Place oil pump drive chain -3- onto sprocket -1- while positioning sprocket -2- on oil pump drive shaft.
Removing and installing timing chain and chain drive for oil pump: drawing 15
  • Hold oil pump drive sprocket with counterhold - T10172-.
  • Tighten new securing bolt -1- to 20 Nm + 1/4 turn (90°) further.
Removing and installing timing chain and chain drive for oil pump: drawing 21
  • Position chain tensioner on oil pump drive chain and tighten securing bolt -3- to 8 Nm.
  • Lever tensioning spring -1- onto bolt -2- using a screwdriver.
  • Tighten sprocket -3- hand-tight with new securing bolt.
Removing and installing timing chain and chain drive for oil pump: drawing 22
  • Place timing chain -1- on crankshaft sprocket -4-, exhaust camshaft sprocket -3-, and tighten camshaft adjuster -2- handtight using a new securing bolt.
Removing and installing timing chain and chain drive for oil pump: drawing 23

Timing chain must lie on guide rail -1- and crankshaft sprocket -arrow-.

Removing and installing timing chain and chain drive for oil pump: drawing 24
  • Install chain tensioner -1- and tighten securing bolts -2- to 9 Nm.
  • Tension timing chain by pulling locking pin - T40011- from chain tensioner.
  • Check marks on crankshaft sprocket and cylinder block; they must align.
Removing and installing timing chain and chain drive for oil pump: drawing 25
  • Tighten securing bolt -2- to 40 Nm and bolt -4- to 50 Nm (use counterhold -T10172- ).
Removing and installing timing chain and chain drive for oil pump: drawing 11

If valve timing is OK:

Removing and installing timing chain and chain drive for oil pump: drawing 26
  • Hold camshaft sprockets with counterhold - T10172- and tighten securing bolts -2- (left-hand thread) and -4- 1/4 turn (90°) further with a rigid wrench.
Removing and installing timing chain and chain drive for oil pump: drawing 27
  • Install oil pump wheel cover -1-.

Remove valve timing housing (Eos, Golf Plus, Scirocco, Golf, Polo, Sharan, Golf Cabriolet) ⇒ 3.1 Removing and installing valve timing housing (Eos, Golf Plus, Scirocco, Golf, Polo, Sharan, Golf Cabriolet).

Remove valve timing housing (Tiguan, Touran).

Remove valve timing housing (Passat, Passat CC)

Removing and installing timing chain and chain drive for oil pump: drawing 28
  • Push engine cover panel down at points -1- in direction of -arrow- until it engages.

Further assembly is basically a reverse of the dismantling sequence.

Specified torque

ComponentSpecified torque
Oil pressure switch - F1-20 Nm

Tightening torques on this page

5 torques

In the steps

StepTorque
Tighten new securing bolt -1- to 20 Nm + 1/4 turn (90°) further.20 Nm
Position chain tensioner on oil pump drive chain and tighten securing bolt -3- to 8 Nm.8 Nm
Install chain tensioner -1- and tighten securing bolts -2- to 9 Nm.9 Nm
Tighten securing bolt -2- to 40 Nm and bolt -4- to 50 Nm (use counterhold -T10172- ).40 Nm / 50 Nm

PartTorque
Oil pressure switch - F1-20 Nm

All tightening torques in this manual →