7-speed DSG gearbox 0AM (DQ200) · VW Polo 6R/6C
Tightening torques
Every tightening torque the 7-speed DSG gearbox 0AM (DQ200) manual gives for the VW Polo 6R/6C, by repair group and procedure. Each one links to its drawing or table in the procedure.
- 22 torques
- 17 procedures
00 – General, Technical Data
Tools
In the steps
| Step | Torque |
|---|---|
| Uncertainties often exist on smaller screws with lower tightening specifications. The Torque Wrench 1783 - 2-10Nm - VAG1783- can be used for these bolts. | 10Nm |
Transmission
In the steps
| Step | Torque |
|---|---|
| Tightening specification for bolts: 8 Nm | 8 Nm |
| Item | Part | Torque |
|---|---|---|
| 8 | Oil Drain Plug | 30 Nm |
30 – Clutch
Overview – Dual Clutch, through Transmission Production Date 05/2011
In the steps
| Step | Torque |
|---|---|
| 6 - Bolts | 8 Nm +90° |
“K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date through 05/2011
| Item | Part | Torque | Notes |
|---|---|---|---|
| 6 | Bolts | 8 Nm +90° | Always replace after removing |
Overview – Dual Clutch, Transmission Production Date from 06/2011
| Item | Part | Torque | Notes |
|---|---|---|---|
| 13 | Bolts | 8 Nm +90° | Always replace after removing |
“K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011
| Item | Part | Torque | Notes |
|---|---|---|---|
| 9 | Bolts | 8 Nm +90° | Always replace after removing |
34 – Controls, Housing
Overview – Mechatronic
All items:Always replace after removing
| Item | Part | Torque | Notes |
|---|---|---|---|
| 1 | Bolt | 10 Nm | M8 x 35 |
| 2 | Bolt | 10 Nm | M8 x 90 |
DSG Transmission Mechatronic J743, Removing with Transmission Installed
In the steps
| Step | Torque |
|---|---|
| Tightening specification: 8 Nm. | 8 Nm |
DSG Transmission Mechatronic J743, Moving into »Removal Position« by Hand
In the steps
| Step | Torque |
|---|---|
| Bolt tightening specification -arrows-: 8 Nm +90° additional turn. | 8 Nm +90° |
DSG Transmission Mechatronic J743, Installing
In the steps
| Step | Torque |
|---|---|
| Diagonally tighten the Mechatronic to 10 Nm. | 10 Nm |
| Tightening Specification: 8 Nm. | 8 Nm |
Special Tools
In the steps
| Step | Torque |
|---|---|
| Torque Wrench 1331 5-50Nm - VAG1331- | 50Nm |
35 – Gears, Shafts
Parking Lock Cover, Removing and Installing
In the steps
| Step | Torque |
|---|---|
| Bolt tightening specification -arrows-: 8 Nm +90° additional turn. | 8 Nm +90° |
| Part | Torque |
|---|---|
| Parking lock cover to transmission housing | 8 Nm |
| Transmission selector lever to selector shaft. | 15 Nm |
Parking Lock, Removing and Installing
| Part | Torque |
|---|---|
| Parking lock to the transmission housing • Replace the bolts after removing them. | 20 Nm +90° |
39 – Final Drive, Differential
Right Stub Shaft Seal, Replacing
In the steps
| Step | Torque |
|---|---|
| Tighten the stub shaft bolt to 30 Nm. Push the stub shaft against the transmission so that the bolt engages in the thread. | 30 Nm |
Left Stub Shaft Seal, Replacing
In the steps
| Step | Torque |
|---|---|
| Tighten the stub shaft bolt to 30 Nm. Push the stub shaft against the transmission so that the bolt engages in the thread. | 30 Nm |
Right Flange Shaft Seal, Replacing
In the steps
| Step | Torque |
|---|---|
| Tighten the new screw to 30 Nm. Push the flange shaft against the transmission so that the bolt engages in the thread. | 30 Nm |
Left Flange Shaft Seal, Replacing
In the steps
| Step | Torque |
|---|---|
| Tighten the new bolt to 30 Nm. Push the flange shaft against the transmission so that the bolt engages in the thread. | 30 Nm |