7-speed DSG gearbox 0AM (DQ200) · Clutch · Dual Clutch, Removing and Installing, from Transmission Production Date 06/2011

“K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011

When replacing the dual clutch and its components, the “K 1 and K 2” engaging bearing position must always be readjusted.

Brief Description

  • The position of the engaging bearing is comparable to clutch play on a manual transmission. There are tolerances in the 7-speed DSG® transmission 0AM engaging system and in the transmission itself. There are also tolerances within the dual clutch. These tolerances must be taken into account separately when performing the adjustments.
  • The following procedure describes how all necessary measurements are determined from the transmission side in order to select the correct shim. In addition to this, the tolerances in the clutch already determined by the manufacturer. The transmission side tolerances and the tolerances in the clutch determine the thickness of the shim.
  • Follow the work sequence.

Overview - Clutch Mechanism

“K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011: drawing 1
  • 1 Shim for “K 1”
  • 2 Large Engaging Lever for “K 1”
    • With engaging bearing
    • Always replace when replacing the dual clutch
  • 3 Engaging Lever Support
    • For the large engaging lever “K 1”
    • Is not replaced
  • 4 Small Engaging Bearing for “K 2”
    • Always replace when replacing the dual clutch
  • 5 Shim for “K 2”
  • 6 Guide Sleeve Upper Section
    • For the small engaging lever “K 2”
    • Removed and installed together with the guide sleeve lower section
  • 7 Small Engaging Lever for “K 2”
    • Is removed and installed together with the guide sleeve upper section and lower section
    • Always replace when replacing the dual clutch
  • 8 Ball Stud
    • For the small engaging lever “K 2”
    • Always replace when replacing the dual clutch
  • 9 Bolts
    • 8 Nm +90°
    • Always replace after removing
  • 10 Guide Sleeve Lower Section
    • For the small engaging lever “K 2”
    • Removed and installed together with the guide sleeve upper section

Special tools and workshop equipment required

  • Digital Depth Gauge - 300mm - VAS6594-
  • Gauge - Clutch Bearings - T10466-
  • Ruler (2 pc.) - T40100-

Requirement

  • The transmission flange must be even so that it has a good surface for the ruler.
  • DSG Transmission Mechatronic - J743- must be installed.
“K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011: drawing 2
  • Remove the ball stud installed using pliers.
“K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011: drawing 3
  • Install the »new« ball stud by hand. Use a plastic hammer and drift gently, if necessary.
“K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011: drawing 4
  • Install the old circlip for the outer input shaft.
“K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011: drawing 5

Step 1: Determine Dimension “B” for “K 1” and “K 2” Clutch.

“K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011: drawing 6
  • Place Ruler (2 pc.) - T40100- across the end of the shaft on the transmission flange.
“K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011: drawing 7
  • Place the Digital Depth Gauge - 300mm - VAS6594- on top of the Ruler (2 pc.) - T40100- and position the depth slide on the outer input shaft.
  • Set the depth gauge to “0”.
“K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011: drawing 8
  • Position the depth slide on the locking ring, as illustrated.
  • Measure dimension “B1 ” on the locking ring in this position.
  • Example: measurement “B1 ” = 2.62 mm
“K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011: drawing 9
  • Measure dimension “B2 ” on the opposite side of the locking ring.
  • Calculate the mean value from “B1 ” and “B2 ”.

    Formula: (B1 + B2) / 2

Example:

  • (2.62 + 2.58) / 2 = 2.60 mm
  • Result: dimension “B” = 2.60 mm
“K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011: drawing 10
  • Remove the circlip from the outer input shaft and dispose of it.
“K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011: drawing 11

Step 2: Determine Dimension “A 1” for the “K 1” Clutch Engaging Bearing.

“K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011: drawing 12
  • Install the large engaging lever.
  • Make sure the engaging lever fits correctly.
“K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011: drawing 13
  • Place the Gauge - Clutch Bearings - T10466- on the large engaging bearing. The flat side faces up
  • Press and turn the Gauge - Clutch Bearings - T10466- to make sure it seats correctly on the engaging bearing.
  • The engaging bearing turns with the Gauge - Clutch Bearings - T10466-.
“K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011: drawing 14
  • Place the Digital Depth Gauge - 300mm - VAS6594- on top of the ruler and position the depth slide on the outer input shaft.
  • The Ruler (2 pc.) - T40100- lies straight across the transmission flange over the end of the shaft.
  • Set the depth gauge to “0”.
“K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011: drawing 15
  • Position the depth slide on the Gauge - Clutch Bearings - T10466-, as illustrated.
  • Measure dimension “A 1a ” on the Gauge - Clutch Bearings - T10466-.
  • Example: dimension “A 1a ” = 4.93 mm
“K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011: drawing 16
  • Measure dimension “A 1b ” on the other side of the Gauge - Clutch Bearings - T10466-.
  • Example: dimension “A 1b ” = 4.91 mm
  • Calculate the average value from dimension “A 1a ” and “A 1b ”.

    Formula: (A 1a + A 1b) / 2

Example:

  • (4.93 + 4.91) / 2 = 4.92 mm
  • Result: dimension “A 1” = 4.92mm

Step 3: Determine the Height Tolerance for the “K 1” Clutch Engaging Bearing.

Dimension “A 1”
–Dimension “B”
=Height tolerance for clutch “K 1” engaging bearing

Example:

  • 4.92 mm – 2.60 mm = 2.32 mm
  • Result: height tolerance for “K 1” clutch engaging bearing = 2.32 mm
“K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011: drawing 17

Step 4: Determine the Clutch Tolerance for the “K 1” Clutch.

  • Read the clutch tolerance value on the new clutch.
  • Example: clutch tolerance read on the clutch “K 1 = +0.2”, as illustrated.
  • Result: clutch “K 1” clutch tolerance = + 0.20 mm.

Step 5: Determine the “SK 1” Shim Thickness.

Height tolerance for the engaging bearing “K 1”
–/+Clutch tolerance for clutch “K 1”
=Calculated thickness for shim “SK 1”

Example:

  • 2.32 mm + 0.20 mm = 2.52 mm
  • Result: calculated “SK 1” shim thickness= 2.52 mm
“K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011: drawing 18
  • Select the shim from the table using the part number -magnifying glass- on the shim and lay it nearby for installation.
Calculated Shim Thickness mmAvailable Shim Thicknesses in mmShim Part Number
1.21 to 1.601.500AM 141 383
1.61 to 1.801.700AM 141 383 A
1.81 to 2.001.900AM 141 383 B
2.01 to 2.202.100AM 141 383 C
2.21 to 2.402.300AM 141 383 D
2.41 to 2.602.500AM 141 383 E
2.61 to 2.802.700AM 141 383 F
2.81 to 3.002.900AM 141 383 G
3.01 to 3.203.100AM 141 383 H
3.21 to 3.403.300AM 141 383 J
3.41 to 3.803.500AM 141 383 K

Example:

  • Result: calculated “SK 1” shim thickness= 2.52 mm
  • Selected shim thickness = 2.50 mm = part number 0AM 141 383 E
“K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011: drawing 12
  • Remove the Gauge - Clutch Bearings - T10466- and large engaging lever.
“K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011: drawing 19

Step 6: Determine Dimension “A 2” for “K 2” Clutch Engaging Bearing

“K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011: drawing 20

Note the Following when Installing A New »K2« Engaging Lever:

A new »K 2« engaging lever with guide sleeve upper and lower sections are in their shipment positions when they are delivered -image-, and they must first be moved into their installation position before installing.

Move the »K 2« engaging lever into its installation position:

“K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011: drawing 21
  • Hold the guide sleeve upper section with one hand. Turn the guide sleeve lower section in direction of -arrow- with the other hand until the sleeve moves freely.
“K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011: drawing 22

In the installed position, the holes in the guide sleeve lower section are at a right angle to the engaging lever and the sleeve can be moved freely.

“K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011: drawing 23

Continuation for All

  • Install the »small« engaging lever with the upper and lower sections of the guide sleeve. Insert new bolts and tighten them.

Tightening specification. Refer to ⇒ 2.3 “K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011.

“K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011: drawing 24
  • Install the »small« engaging bearing without the shim.
“K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011: drawing 25
  • Turn the small engaging bearing to make sure it is installed correctly and fits correctly in the grooves.
“K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011: drawing 13
  • Place the Gauge - Clutch Bearings - T10466- on the small engaging bearing. The flat side faces up
  • Press and turn the Gauge - Clutch Bearings - T10466- to make sure it seats correctly on the engaging bearing.
  • The engaging bearing turns with the Gauge - Clutch Bearings - T10466-.
“K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011: drawing 26
  • Place the Digital Depth Gauge - 300mm - VAS6594- on top of the ruler and position the depth slide on the outer input shaft.
  • The Ruler (2 pc.) - T40100- lies straight across the transmission flange over the end of the shaft.
  • Set the depth gauge to “0”.
“K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011: drawing 15
  • Position the depth slide on the Gauge - Clutch Bearings - T10466-, as illustrated.
  • Measure dimension “A 2a ” on the Gauge - Clutch Bearings - T10466-.
  • Example: dimension “A 2a ” = 4.79 mm
“K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011: drawing 27
  • Measure dimension “A 2b ” on the other side of the Gauge - Clutch Bearings - T10466-.
  • Example: dimension “A 2b ” = 4.75 mm
  • Calculate the average value from dimension “A 2a ” and “A 2b ”.

    Formula: (A 2a + A 2b) / 2

Example:

  • (4.79 + 4.75) / 2 = 4.77 mm
  • Result: dimension “A 2” = 4.77 mm

Step 7: Determine the Height Tolerance for the “K 2” Clutch Engaging Bearing.

Dimension “A 2”
–Dimension “B”
=Height tolerance for clutch “K 2” engaging bearing

Example:

  • 4.77 mm - 2.60 mm = 2.17 mm
  • Result: height tolerance for clutch “K 2” engaging bearing = 2.17 mm
“K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011: drawing 17

Step 8: Determine the Clutch Tolerance for the “K 2” Clutch.

  • Read the clutch tolerance value on the new clutch.
  • Example: clutch tolerance read on the clutch “K 2 = – 0.2”, as illustrated.

Step 9: Determine the “SK 2” Shim Thickness.

Height tolerance for the engaging bearing “K 2”
–/+Clutch tolerance for the clutch “K 2”
=Calculated thickness for shim “SK 2”

Example:

  • 2.17 mm – 0.20 mm = 1.97 mm
  • Result: calculated shim thickness “SK 2” = 1.97 mm
“K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011: drawing 28
  • Measure the needed shim from the shims supplied and keep it close for installation.
Calculated Shim Thickness mmAvailable Shim Thicknesses in mm
0.31 to 0.900.80
0.91 to 1.101.00
1.11 to 1.301.20
1.31 to 1.501.40
1.51 to 1.701.60
1.71 to 1.901.80
1.91 to 2.102.00
2.11 to 2.302.20
2.31 to 2.502.40
2.51 to 2.702.60
2.71 to 3.302.80

Example:

  • Result: calculated shim thickness “SK 2” = 1.97 mm
  • Selected shim thickness = 2.00 mm

Tightening torques on this page

1 torque

Drawing with the item numbers:
ItemPartTorqueNotes
9Bolts8 Nm +90°Always replace after removing

All tightening torques in this manual →