1.6 TDI CR engine (EA189) · Cooling · Coolant pipes
Removing and installing coolant pipes
⇒ 3.2.1 Removing and installing front coolant pipe, Polo
⇒ 3.2.4 Removing and installing right coolant pipes, Polo
3.2.1 Removing and installing front coolant pipe, Polo
Special tools and workshop equipment required

- Release lever - 80 - 200-

- Spring-type clip pliers - VAS 6362-

Removing
- Drain coolant ⇒ 1.3 Draining and adding coolant.
- Remove air filter housing ⇒ 7.2.2 Removing and installing air filter housing, Polo.
- Remove oil filter bracket with engine oil cooler ⇒ 3.2 Removing and installing oil filter housing

- Country-specific version for cold countries: Disconnect electrical connector -2-.
- Press release buttons and remove hose -1- for venting crankcase.
- Pull off vacuum hose -arrow-.
- Unscrew bolt -3-, swing air pipe with inlet connection to rear and pull off from turbocharger.

- Unclip wiring harness from retainer -arrow-.

- Free wiring harnesses -arrows- and electrical connector -1- at bracket.

- Remove air intake hose. To do this, loosen hose clips -1, 2-.

- Unscrew bolts -arrows-.
- Free electrical wiring and hoses on left air pipe using removal lever - 80 - 200-.
- Loosen hose clip -1- and remove left air pipe.

- Disconnect coolant hoses and free them, loosening hose clips -1- to do so.

- Remove electrical connector -2- for Hall sender - G40- from retainer and separate.
- Remove bracket from front coolant pipe.
- Remove coolant hoses after loosening hose clips -1- and -3-.
- Undo bolts -arrows- and pull front coolant pipe off cylinder block towards the left.
Installing
Install in reverse order of removal, observing the following.
- Specified torques ⇒ 3.1.2 Assembly overview - coolant pipes, Polo
- Clean or smoothen sealing surface for O-ring.
- Moisten O-ring with coolant and slide onto front coolant pipe.
- Push front coolant pipe into cylinder block.
- Installing intake hoses with screw-type clips ⇒ 2.3 Assembly overview - charge-air hose connections.
- Install charge air pipe ⇒ 2.1.3 Assembly overview - charge air system, Polo.
- Install air pipe with inlet connection.
- Install oil filter bracket with engine oil cooler ⇒ 3.2 Removing and installing oil filter housing.
- Install air filter housing ⇒ 7.2.2 Removing and installing air filter housing, Polo.
- Add coolant ⇒ 1.3.2 Filling with coolant.
3.2.4 Removing and installing right coolant pipes, Polo
Special tools and workshop equipment required

- Hose clamps to 25 mm - 3094-

- Drip tray for workshop hoist - VAS 6208-

- Spring-type clip pliers - VAS 6362-
Removing
- Remove noise insulation:
Polo ⇒ General body repairs, exterior; Rep. gr. 50; Noise insulation; Assembly overview - noise insulation

- Disconnect electrical connector -2- and free off electrical wiring.
- Place drip tray - VAS 6208- beneath engine.
- Clamp off coolant hoses with hose clamps -3094- and remove from right coolant pipes, releasing hose clips -1, 3- to do so.
- Undo bolts -arrows- and remove coolant pipes on right.
Installing
Install in reverse order of removal, observing the following.
- Specified torque ⇒ 3.1.2 Assembly overview - coolant pipes, Polo.
- Install noise insulation:
Polo ⇒ General body repairs, exterior; Rep. gr. 50; Noise insulation; Assembly overview - noise insulation
- Check coolant level ⇒ 1.3 Draining and adding coolant.