1.6 TDI CR engine (EA189) · Turbocharging/supercharging · Turbocharger

Removing and installing turbocharger

⇒ 1.2.4 Removing and installing turbocharger, Polo

1.2.4 Removing and installing turbocharger, Polo

Special tools and workshop equipment required

Removing and installing turbocharger: drawing 1
  • Tool insert, AF 17 mm - T10395-
Removing and installing turbocharger: drawing 2
  • Transport lock - T10403-
Removing and installing turbocharger: drawing 3
  • Torque wrench - V.A.G 1331-
  • Used oil collection and extraction unit, e.g. -V.A.G 1782-

If foreign objects are found in the charge air system, the charged air routing must be cleaned and the charge air cooler must be renewed, if necessary.

⇒ 2 Safety information

⇒ 3.1 Rules for cleanliness

Removing

  • With ignition switched off, disconnect battery earth strap. ⇒ Electrical system; Rep. gr. 27; Battery; Disconnecting and connecting battery
  • Remove engine cover panel ⇒ 3 Engine cover panel.
Removing and installing turbocharger: drawing 4
  • Pull connector -1- off position sender for charge pressure positioner - G581- on turbocharger.
  • Remove air filter housing with air mass meter and intake hose ⇒ 7.2.2 Removing and installing air filter housing, Polo.
  • Remove plenum chamber bulkhead ⇒ General body repairs, exterior; Rep. gr. 50; Plenum chamber bulkhead; Assembly overview - bulkhead.
Removing and installing turbocharger: drawing 5
  • Loosen particulate filter. To do this, unscrew bolt -1-.
  • Loosen bolt -2- and remove clamp.
Removing and installing turbocharger: drawing 6
  • Disconnect connector -3-.
  • Unscrew bolt -2-, remove pressure differential sender - G 505-, free hoses -1-.
Removing and installing turbocharger: drawing 7
  • On flexible joint in front exhaust pipe, fasten the transport lock - T10403- -arrow-.
Removing and installing turbocharger: drawing 8
  • Unscrew bolts -1- and nuts -2-, remove bracket for particulate filter.
Removing and installing turbocharger: drawing 9
  • Pull particulate filter from mountings -arrows-.
Removing and installing turbocharger: drawing 10
  • Loosen securing bolts -arrows- of clamping sleeve, then push down backwards from front exhaust pipe.
  • Move particulate filter to side and fix using suitable means.

Right-hand drive vehicles ⇒ 2.1.4 Assembly overview - front exhaust pipe with particulate filter, Polo, right-hand drive

Continued for all vehicles

Removing and installing turbocharger: drawing 11
  • Unscrew bolts -arrows-.
  • Take off pulsation damper -2-.
Removing and installing turbocharger: drawing 12
  • Unscrew bolts and remove pipes -A- for exhaust gas recirculation.
Removing and installing turbocharger: drawing 13
  • Unscrew bolts -arrows- and remove heat shield.
Removing and installing turbocharger: drawing 14

Remove bolts -arrows- from exhaust gas recirculation cooler in order to pull exhaust manifold from studs.

Removing and installing turbocharger: drawing 15
  • Unscrew nuts -arrows- and pull turbocharger with exhaust manifold off cylinder head.
Removing and installing turbocharger: drawing 16
  • Carefully remove turbocharger from above in direction of gearbox.

Installing

  • Install in reverse order. During this procedure, observe the following:
  • Note installation position of exhaust temperature sender 1 - G 235-.
Removing and installing turbocharger: drawing 17

Installation position of exhaust gas temperature sender with angled cable guide

Specified torques:

Removing and installing turbocharger: drawing 18
  • Observe sequence when installing particulate filter:
1)Position particulate filter on turbo charger and loosely attach clip -1-
2)Screw in nuts -2, 4- and bolts -3, 5- loosely by hand • It must still be possible to move particulate filter and bracket
3)Tighten clip -1-
4)Tighten nuts -2, 4-
5)Tighten bolts -3, 5-