SSP 390 The 7-speed Double-clutch Gearbox 0AM

Selector lever

Actuation

Actuation (S390_005)

The selector lever is actuated as in vehicles with automatic gearboxes. The double-clutch gearbox also offers the option of shifting using Tiptronic.

Precisely as in vehicles with automatic gearboxes, the selector lever is equipped with a selector lever lock and an ignition key withdrawal lock. The lock functions as before. The design is new.

The selector lever positions are:

P - Park
To move the selector lever from this position, the ignition must be "on" and the foot brake must be depressed. The release button on the selector lever must also be pressed.

Actuation (S390_006)

R - Reverse gear
The release button must be pressed to engage this gear.

N - Neutral position
In this position, the gearbox is in neutral. If the selector lever is set to this position for a long time, the foot brake must be depressed again to move it from this position.

D - Drive position (Normal programme)
In this drive position, the forwards gears are shifted automatically.

S - Sport
Automatic gear selection is carried out according to a "sporty" characteristic curve, which is stored in the control unit.

+ and –
The Tiptronic functions can be carried out in the right-hand selector lever gate and at the steering wheel switches.

Design of the selector lever

Selector lever E313

Hall senders in the selector lever mounting register the position of the selector lever and make it available to the mechatronic unit via the CAN bus.

Selector lever lock solenoid N110

The solenoid locks the selector lever in the "P" and "N" positions. The solenoid is controlled by the selector lever sensors control unit J587.

Selector lever locked in position P switch F319

If the selector lever is in the "P" position, the switch transmits the signal – selector lever in "P" position – to the steering column electronics control unit J527. The control unit requires this signal to control the ignition key withdrawal lock.

Selector lever locked in position P switch F319 (S390_007)

Selector lever lock solenoid N110

How it works

Selector lever locked in "P" position

Selector lever locked in "P" position (S390_008)

If the selector lever is set to "P", the locking pin is located in locking pin latch "P". This prevents the locking lever from being moved unintentionally.

Selector lever released

Selector lever released (S390_009)

After switching on the ignition and actuating the foot brake, the selector lever sensors control unit J587 supply the selector lever lock solenoid N110 with current. As a result of this, the locking pin is withdrawn from the locking pin latch "P".

The selector lever can now be moved to the drive position.

Selector lever locked in "N" position

Selector lever locked in "N" position

If the selector lever is set to the "N" position for longer than 2 sec., the control unit supplies the solenoid with current. As a result of this, the locking pin is pressed into locking pin latch "N". The selector lever can no longer be unintentionally moved into a gear. The locking pin is released when the brake is actuated.

Emergency release

Emergency release (S390_011)

If the voltage supply to the selector lever lock solenoid N110 fails, the selector lever can no longer be moved, because selector lever lock "P" remains activated in the event of a power failure.

By mechanically "pressing in" the locking pin with a narrow object, the lock can be released and the selector lever can be "emergency released" to the "N" position.

The vehicle can be moved again.

Ignition key withdrawal lock

Ignition key withdrawal lock (S390_012)

The ignition key withdrawal lock prevents the ignition key from being turned back to the removal position if the parking lock is not engaged.

It functions electromechanically and is controlled by the steering column electronics control unit J527.

The steering column electronics control unit J527 detects the open switch. The ignition key withdrawal lock solenoid N376 is not supplied with current. The compression spring in the solenoid pushes the locking pin into the release position.

How it works

Selector lever in "park position", the ignition is switched off. If the selector lever is set to the park position, the selector lever locked in position "P" switch F319 is opened.

How it works (S390_013)

How it works

Selector lever in "drive position", the ignition is switched on.

If the selector lever is set to the drive position, the selector lever locked in position "P" switch F319 is closed.

The steering column electronics control unit then supplies the ignition key withdrawal lock solenoid N376 with current. The locking pin is pushed, overcoming the force of the compression spring, into the locked position by the solenoid.

In the locked position, the locking pin prevents the ignition key from being turned back and withdrawn.

Only when the selector lever is pushed into the park position does the selector lever locked in position "P" switch open, and the control unit swtches off the current supply to the solenoid.

The locking pin is then pressed back by the compression spring. The ignition key can be turned further and can be removed.

How it works (S390_014)