1.6 TDI CR engine (EA189) · Lubrication · Oil circuit
Removing and installing oil supply line
⇒ 4.2.1 Removing and installing oil supply line, Polo
4.2.1 Removing and installing oil supply line, Polo

Torque wrench - V.A.G 1331-

Tool insert, AF 17 mm - T10395-

Used oil collection and extraction unit - V.A.G 1782-
Removing
- Remove engine cover panel ⇒ 3 Engine cover panel.
- Remove plenum chamber bulkhead ⇒ General body repairs, exterior; Rep. gr. 50; Plenum chamber bulkhead; Assembly overview - bulkhead.
- Remove noise insulation:
Polo ⇒ General body repairs, exterior; Rep. gr. 50; Noise insulation; Assembly overview - noise insulation

- Remove drive shaft shield.
Loosen particulate filter to create space for removing and installing the oil supply line with turbocharger support.

- Pull electrical connector -2- from pressure differential sender - G 505-.
- Unclip pressure differential sender - G 505- from lower part of fuel filter.

- Remove securing clamp -1- between particulate filter and turbocharger.
- Remove securing clamp -1- between particulate filter and turbocharger.

- Loosen bolt -1-.

- Unscrew nuts -2-, nuts -1- should be disregarded.

- Now unscrew bolt -1-.
- Push particulate filter aside and fix it in position on plenum chamber bulkhead using suitable means.
to create space for removing and installing the oil supply line with turbocharger support.

- Remove connection pipe -2- leading to cooler for exhaust gas recirculation.

- Loosen oil supply line union nut -arrow- on turbocharger.
Collect escaping oil using used oil collection and extraction unit - V.A.G 1782-.
- Loosen the banjo bolt of the oil supply line ⇒ Item 11 (4.1.2 Assembly overview - oil supply line, Polo) on the cylinder block.

- Now you can access the securing bolt -arrow- on the retaining clamp for the oil return line on the turbocharger support.
- Unscrew bolt -arrow-.

- Unscrew oil supply line at turbocharger.
- Remove oil supply line.
- Remove exhaust gas temperature sender 1 - G 235-.

- Unscrew upper bolt -arrow- from support on turbocharger.
- Remove banjo bolt ⇒ Item 10 (4.1.2 Assembly overview - oil supply line, Polo) of turbocharger support.
- Remove bolts for oil return line ⇒ Item 1 (4.1.2 Assembly overview - oil supply line, Polo).
- Remove turbocharger support with oil return pipe.
Installing
- Position oil return line on turbocharger together with turbocharger support on turbocharger and crankcase.
- Fit oil supply line onto turbocharger and crankcase.
- First, bolt the turbocharger support onto the crankcase ⇒ Item 10 (4.1.2 Assembly overview - oil supply line, Polo) and turbocharger ⇒ Item 5 (4.1.2 Assembly overview - oil supply line, Polo) by hand.
- Then tighten the turbocharger support bolts in several steps up to the specified torque, alternating between the crankcase ⇒ Item 10 (4.1.2 Assembly overview - oil supply line, Polo) and turbocharger ⇒ Item 5 (4.1.2 Assembly overview - oil supply line, Polo).
- Next tighten the oil supply line union nut and the banjo bolt for the oil supply line on the crankcase.
- Finally tighten the bolt on the oil supply line/turbocharger support clamp.
Specified torques ⇒ 4.1.2 Assembly overview - oil supply line, Polo.
- Further assembly in reverse order of removal.
Install particulate filter ⇒ 2.2 Removing and installing particulate filter.
Installation position of exhaust gas temperature sender -G 235-.

Angled shaft must have a distance -a- = 3 … 5 mm to bolting of turbocharger support.