Contents

SSP 308 Direct Shift Gearbox 02E

Selector lever

Operation

Operation (S308_004)

The selector lever is actuated in the vehicle in the same way as an automatic gearbox. The direct shift gearbox also offers the option of Tiptronic gear selection.

As in vehicles with automatic gearboxes, the selector lever features lever locks and an ignition key lock. The function of the locks remains unchanged. The design, however, is new.

The gear selector lever positions are:

Operation (S308_063)

P - Park
To move the selector lever out of this position, the ignition must be "on" and the brakes applied. Furthermore, the release button on the selector lever must be pressed.

R - Reverse gear
To engage reverse gear, the release button must be pressed.

N - Neutral position
In this position, the gearbox is at idle. If, for a length of time, the gear selector lever is left in this position, the brake pedal must be pressed for it to be moved.

D - Drive
In this position, the forward gears are selected automatically.

S - Sport
Gears are selected automatically using a "sporty" program stored in the control unit.

+ and –
The Tiptronic functions can be used with the selector lever in the right gate and with the steering wheel gear selectors.

Design of selector lever

Selector lever sensors control unit J587

Hall sensors in the gear selector lever mounting detect the position of the selector lever and make the positions available to the mechatronics via the CAN bus .

Selector lever lock solenoid N110

Solenoids hold the selector lever in positions "P" and "N". The solenoid is activated by the selector lever sensor control unit J587.

Selector lever locked in position "P" switch F319

If the selector lever is in the "P" position, selector lever locked in position "P" switch sends a signal to the steering column electronics control unit J527. The control unit requires this signal for actuation of the ignition key withdrawal lock.

Selector lever locked in position "P" switch F319 (S308_098)

Selector lever lock solenoid N110

This is how it works

Selector lever locked in "P"

Selector lever locked in "P" (S308_103)

When the selector lever is in the "P" position, the locking pin is in the locking pin hole for "P". This way, the selector lever is stopped from being moved inadvertently out of position.

Selector lever released

Selector lever released (S308_101)

When the ignition is switched on and the brake pedal is pressed, the selector lever sensors control unit J587 energises the solenoid N110. In this way, the locking pin is pulled out of the locking pin hole "P".

The selector lever can now be moved into the drive position.

Selector lever locked in "N"

Selector lever locked in "N" (S308_102)

If the selector lever is in the "N" position for longer than 2 seconds, the control unit will energise the solenoid. In this way, the locking pin is pushed into the locking pin hole "N". The selector lever can no longer be moved inadvertently into a drive position. The locking pin is released when the brake pedal is pressed.

Emergency release

Emergency release (S308_104)

If the power supply fails to the selector lever lock solenoid N110, the selector lever can no longer be moved because selector lever lock "P" remains activated in the event of power failure.

By pressing in the locking pin mechanically using a thin object, the lock can be released and the selector lever can be moved out of the "N" position for emergency purposes.

The vehicle can then be driven again.

Ignition key withdrawal lock

The ignition key withdrawal lock prevents the ignition key from being turned to the withdrawal position unless the parking lock is engaged.

It works on an electro-mechanical principle and is actuated by the steering column electronics control unit J527.

The steering column electronics control unit J527 detects the open switch. The ignition key withdrawal lock solenoid N376 is not supplied with power. The spring in the solenoid pushes the locking pin to the release position.

This is how it works

This is how it works (S308_093)

Selector lever in "park position", ignition switched off. When the selector lever is in the park position, the "selector lever locked in position P" F319 is open.

This is how it works

This is how it works

"Selector lever in drive position", ignition on.

In the drive position, the "selector lever locked in position P" switch F319 is closed.

The steering column electronics control unit then energises the ignition key withdrawal lock solenoid N376. The locking pin is pushed into the lock position against spring pressure by the solenoid.

In the lock position, the locking pin prevents the ignition key from being turned back and withdrawn.

Not until the selector lever is placed in the park position is the "selector lever locked in position P" switch opened. The control unit then isolates the power supply to the solenoid.

The locking pin is then pushed back by the spring. The ignition key can be turned further and withdrawn.

This is how it works