# Test yourself – SSP 390 The 7-speed Double-clutch Gearbox 0AM

> Seventeen questions on the double-clutch gearbox 0AM, its clutches, mechatronic unit, valves and senders, with the answers.

- Web page: https://catalog.polo.blue/self-study/ssp-390-7-speed-double-clutch-gearbox-0am/test-yourself/
- Original document (PDF): https://cdn.polo.blue/files/SSP-390-7-speed-double-clutch-gearbox-0AM.pdf

**Which answers are correct?**

One or several of the given answers may be correct.

## 1. Which statements about the double-clutch gearbox 0AM are correct?

1. The gearbox is equipped with a double clutch.
2. The gearbox has 7 forwards gears and one reverse gear.
3. The mechatronic unit and the mechanical gearbox each have a separate oil circuit.
4. The oil pump is driven subject to requirements.

## 2. Onto which shaft does clutch K1 transmit the engine torque?

1. Onto output shaft 2.
2. Onto output shaft 1.
3. Onto drive shaft 1.
4. Onto drive shaft 2.

## 3. Please name the components!

![3. Please name the components! (S390\_105)](https://catalog.polo.blue/instructions/ssp-390/a1e25503a242d632.webp)

## 4. Please complete the text!

…………… independent, …………… clutches operate in the double clutch. They each conduct the engine torque  
into …………… gear train half.  
When the engine is switched off, …………… clutches are …………… .  
During vehicle operation, only …………… of the clutches is ever …………… .

## 5. Which gear is engaged in the illustration?

1. 1st gear.
2. 4th gear.
3. R gear.
4. 7th gear.

![5. Which gear is engaged in the illustration? (S390\_034)](https://catalog.polo.blue/instructions/ssp-390/ccb4959466cf48d5.webp)

## 6. Which statement about the mechatronic unit is correct?

1. The mechatronic unit is the central gearbox control unit.
2. It consists of one module, in which the electronic control unit and the electrohydraulic control unit are comprised.
3. The mechatronic unit has a separate oil circuit.
4. It is connected to the oil circuit of the mechanical gearbox.

## 7. Please complete the text!

The electrohydraulic control unit is integrated into the …………… .  
It generates the …………… which is required to …………… and to actuate the …………… .

## 8. Please name the components!

![8. Please name the components! (S390\_106)](https://catalog.polo.blue/instructions/ssp-390/93f7936e06140d83.webp)

## 9. Please name the components!

![9. Please name the components! (S390\_104)](https://catalog.polo.blue/instructions/ssp-390/1fb4cb7699a6ebcc.webp)

## 10. Via valve 2 in gear train half 1 N434,

1. 1st and 3rd gears are shifted.
2. 4th and 2nd gears are shifted.
3. 7th and 5th gears are shifted.

## 11. Which statement is correct?

1. The motor for the hydraulic pump is a brushless DC motor.
2. The brushless DC motor is actuated by the engine control unit.
3. It drives the hydraulic pump via a coupling.

## 12. Valve 4 in gear train half 2 N440

1. Is a gear train half pressure control valve.
2. It controls the oil pressure for gear train half 2.
3. Gear train half 1 can be shut off via this valve.

## 13. Please complete the text!

The gearbox input speed sender G182 is inserted into the …………… .  
It electronically scans the starter ring gear and therefore records the …………… .  
The gearbox input speed signal is required by the control unit to …………… and ……………  
the clutches.  
In the event of signal failure, the control unit uses the …………… signal as a substitute signal.

## 14. A clutch travel sender consists of

1. An iron core, around which a primary coil is wrapped
2. A Hall sender
3. Two secondary coils
4. A permanent magnet and
5. The sensor electronics

## 15. Which measures are introduced by the electronic gearbox control unit as of a mechatronic unit temperature of approx. 140°C?

1. One gear train half is shut off.
2. The system immediately shifts to the next highest gear.
3. Engine torque reduction is introduced.

## 16. Which measures are introduced if a clutch actuator solenoid valve fails?

1. The gear train half for the affected clutch is shut off.
2. The affected clutch is no longer actuated.
3. The clutch actuator solenoid valve for the other clutch also controls the affected clutch.

## 17. What are the effects if the motor for hydraulic pump fails?

1. The hydraulic pressure drops.
2. The clutches open independently.
3. The failure of a motor for hydraulic pump has no effects, because the hydraulic pump continues to work.

**Answers:**

1. a, b, c, d; 2. c;

3. 1 = reverse gear, 2 = 5th gear, 3 = reverse gear intermediate gear, 4 = 1st gear;

4. two independent dry clutches operate, … one gear half train, … both clutches open, … only one of the clutches is ever closed;

5. c; 6. a, b, c;

7. … integrated into the mechatronic module, … the oil pressure, which is required to change the gears …, … the clutches…

8. 1 = Gear selector for gears 5 and 7, 2 = Gearbox input speed sender 2 G612, 3 = Gear selector for gears 2 and 4, 4 = Gearbox input speed sender G182;

9. 1 = Pressure limiting valve, 2 = Pressure accumulator, 3 = Hydraulic pressure sender, 4 = Valve 4 in gear train half 1 N436, 5 = Valve 3 in gear train half 1 N435

10. c; 11. a, c; 12. a, b;

13. … into the gearbox housing, … the gearbox input speed, … to control the clutches and calculate clutch slip, … the engine speed;

14. a, b, d, e; 15. c, 16. a, b; 17. a, b
