# Sensors – SSP 390 The 7-speed Double-clutch Gearbox 0AM

> Clutch travel senders, input speed senders, temperature and pressure senders, gear selector sensors and Tiptronic switches.

- Web page: https://catalog.polo.blue/self-study/ssp-390-7-speed-double-clutch-gearbox-0am/sensors/
- Original document (PDF): https://cdn.polo.blue/files/SSP-390-7-speed-double-clutch-gearbox-0AM.pdf

## Clutch travel sender 1 G617, clutch travel sender 2 G618

The clutch travel senders are located in the mechatronic unit above the clutch actuators.

The double clutch control system requires reliable and precise recording of the current clutch actuation status.

For this reason, contact-free sensor technology is used to record clutch travel.

Contact-free position recording increases the reliability of the sensor functions. Measured value falsification caused by wear and vibrations is avoided.

![Clutch travel sender 1 G617, clutch travel sender 2 G618 (S390\_050)](https://catalog.polo.blue/instructions/ssp-390/71c0de5e6886065e.webp)

### Signal use

The control unit requires these signals to control the clutch actuators.

### Effects of signal failure

If clutch travel sender 1 G617 fails, gearbox path 1 is shut off. Gears 1, 3, 5 and 7 can no longer be engaged.

If clutch travel sender 2 G618 fails, gears 2, 4, 6 and R can no longer be engaged.

## Clutch travel sender

### Design

A clutch travel sender consists of:

- An iron core, around which the primary coil is wound
- Two secondary evaluation coils
- A permanent magnet, which is located on the clutch actuator piston, and
- The sensor electronics

### How it works

An alternating voltage is applied to the primary coil. As a result of this, a magnetic field is built up around the iron core. If the clutch is actuated, the clutch actuator piston moves through the magnetic field with the permanent magnet. Due to the permenant magnet's movement, a voltage is induced in the secondary evaluation coils. The level of the voltage induced in the left and right evaluation coils is dependent on the position of the permanent magnet. Via the level of the voltage in the left and right evaluation coils, the sensor electronics detect the position of the permanent magnet and therefore the position of the clutch actuator piston.

![How it works (S390\_091)](https://catalog.polo.blue/instructions/ssp-390/66bae73e6b230a32.webp)

## Gearbox input speed sender G182

The gearbox input speed sender is inserted into the gearbox housing. It is the only sensor located outside of the mechatronic unit. It electronically scans the starter ring gear and thereby records the gearbox input speed.

The gearbox input speed is identical to the engine speed. The sender operates according to the Hall principle.

![Gearbox input speed sender G182 (S390\_073)](https://catalog.polo.blue/instructions/ssp-390/7496c75e830cd86c.webp)

### Signal use

The control unit requires the gearbox input speed signal to control the clutches and to calculate slip. To do this, it compares the signals from the gearbox input speed sender G182 before the clutches with the signals from senders G612 and G632, which transmit speed signals from the drive shafts.

### Effects of signal failure

In the event of signal failure, the control unit uses the engine speed signal as a substitute signal. It obtains this signal from the engine control unit via the CAN bus.

## Gearbox input speed sender 1 G632 and gearbox input speed sender 2 G612

Both senders are housed in the mechatronic unit.

- Sender G632 scans an impulse wheel, which is located on drive shaft 1. From this signal, the control unit calculates the speed of drive shaft 1.

- Sender G612 scans a gear on drive shaft 2. From this signal, the control unit calculates the speed of drive shaft 2.

Both senders are Hall senders.

![Gearbox input speed sender 1 G632 and gearbox input speed sender 2 G612 (S390\_049)](https://catalog.polo.blue/instructions/ssp-390/1df547cd009f7d80.webp)

### Signal use

The speed signals from drive shafts 1 and 2 are used by the control unit to control the clutch and to calculate clutch slip.

### Effects of signal failure

If sender G632 fails, gear train half 1 is shut off. The vehicle can then only be driven in gears 2, 4, 6 and R.

If sender G612 fails, gear train half 2 is shut off. The vehicle can then only be driven in gears 1, 3, 5 and 7.

## Temperature sender in control unit G510

The temperature sender is located directly in the mechatronic unit's electronic control unit.

Hot hydraulic oil constantly flows around the control unit, thereby heating it. Severe heating may impair the functions of the electronics.

The sender measures the temperature directly of the components at risk. As a result, measures to reduce the oil temperature can be introduced at an early stage, thereby avoiding excessive heating.

![Temperature sender in control unit G510 (S390\_074)](https://catalog.polo.blue/instructions/ssp-390/2c28ae02f4086196.webp)

### Signal use

The sender's signal is used to check the mechatronic unit's temperature.

At a temperature of 139 °C, engine torque reduction can be implemented.

### Effects of signal failure

In the event of signal failure, the control unit uses an internally available substitute value.

## Gearbox hydraulic pressure sender G270

The hydraulic pressure sender is integrated into the mechatronic unit's hydraulic oil circuit. It is designed as a diaphragm pressure sender.

> Further information on the hydraulic pressure sender can be found in [self-study programme 308](https://catalog.polo.blue/self-study/ssp-308-direct-shift-gearbox-dq250-02e/) "The Direct Shift Gearbox 02E".

![Gearbox hydraulic pressure sender G270 (S390\_075)](https://catalog.polo.blue/instructions/ssp-390/263b1dcf9b6788bf.webp)

### Signal use

The control unit uses the signal to control the motor for the hydraulic pump V401. At a hydraulic oil pressure of approx. 60 bar, the motor is shut off according to the pressure sender signal, and is switched on again at approx. 40 bar.

### Effects of signal failure

In the event that the signal fails, the motor for hydraulic pump runs continuously. The hydraulic pressure is determined by the pressure control valve.

## Gear selector movement sensors 1 to 4, G487 to G490

The gear selector movement sensors are located in the mechatronic unit.

On combination with the solenoids on the selector forks, they generate a signal, from which the control unit recognises the precise position of the gear selectors.

![Gear selector movement sensors 1 to 4, G487 to G490 (S390\_051)](https://catalog.polo.blue/instructions/ssp-390/9f99cce2338ff8cc.webp)

### Signal use

The control unit requires the precise position of the gear selectors to control the gear selectors for changing gears.

### Effects of signal failure

If a movement sensor fails, the control unit cannot detect the position of the corresponding gear selector. As a result, the control unit is unable to recognise whether or not a gear is changed via the gear selector and the selector fork. To prevent damage to the gearbox, the gearbox path of the movement sensor which has failed is shut off in this case.

## Selector lever E313

The selector lever sensor system and the control system for the selector lever lock solenoid are integrated into the selector lever. The selector lever positions are detected by Hall sensors, which are integrated into the selector lever sensor system. The selector lever position signals and the Tiptronic signals are transmitted via the CAN bus to the mechatronic unit and to the control unit in the dash panel insert.

### Signal use

![Signal use (S390\_052)](https://catalog.polo.blue/instructions/ssp-390/0315c5e8d0bd4126.webp)

Based on the signals, the control unit detects the selector lever positions. It uses the signals to implement the driver's D-R-S or Tiptronic command and to control starter release.

### Effects of signal failure

If the control unit detects no selector lever position, both clutches are opened.

## Tiptronic switches in steering to shift up and down E438 and E439

![Tiptronic switches in steering to shift up and down E438 and E439 (S309\_099)](https://catalog.polo.blue/instructions/ssp-390/005529d44a5397e1.webp)

The switches are located on the right and left on the steering wheel. The gears can be shifted up and down by actuating the switches. The shift signals are transmitted from the steering column electronics control unit J527 to the mechatronic unit for direct shift gearbox J743 via the CAN bus.

### Signal use

In Tiptronic mode, the gears can also be shifted up and down using the steering wheel switches. If the Tiptronic switches on the steering wheel are actuated in automatic mode, the gearbox control system switches to Tiptronic mode. If the Tiptronic switches on the steering wheel are no longer actuated, the gearbox control system automatically switches back to automatic mode following the expiry of a timer.

### Effects of signal failure

In the event of signal failure, no Tiptronic functions are possible via the steering wheel switches.

### Tiptronic shifting strategy

- Automatic upshifting on reaching the maximum engine speed
- Automatic downshifting on falling below the minimum engine speed
- Kick-down downshifting
