# Measured value blocks of the gearbox 02E – SSP 094 Diagnosis of the automatic gearboxes 0AM and 02E

> Which blocks to read on the 02E: switches, speeds, clutch currents and pressures, adjuster paths, oil temperatures and the environmental conditions.

- Web page: https://catalog.polo.blue/self-study/ssp-094-diagnosis-of-the-automatic-gearboxes-0am-02e/measured-value-blocks-02e/
- Original document (PDF): https://cdn.polo.blue/files/SSP-094-Diagnosis-of-the-automatic-gearboxes-0AM-and-02E.pdf

Selected measured value blocks of the gearbox electronics serve to carry out a correct fault diagnosis on the automatic gearboxes DSG. Therefore, if a fault is detected on the automatic gearbox, a printout of all the measured value blocks must be sent (at idle speed, if the vehicle is stationary in P, N or D mode)

The following information can be read in the measured value blocks (MVB):

- Identification of the software and hardware level of the automatic gearbox control unit
- current operating values (oil pressure values in the mechatronics, positions of the individual gear adjusters, clutch status, speeds of the individual shafts, selector lever position, etc.)
- the current values recorded during the operation (journey time in the individual driving modes, operating temperatures of the clutches, journey time in all operating temperatures, warnings, etc.
- specific environmental conditions when the last two faults occured

## Important measured value blocks

**Measured value blocks**

| Nbr. | Description | Value example |
| --- | --- | --- |
| 1.1 | Brake light switch F |  |
| 1.2 | Brake light switch F47 |  |
| 1.3 | Shift lock N110 I) |  |
| 1.4 | Vehicle speed |  |
| 3.3 | Tiptronic shifting on steering wheel + II) |  |
| 3.4 | Tiptronic shifting on steering wheel – II) |  |
| 4.1 | Position of the selector lever | P, R, N, D, S, TT, PL, MI, RS, ER IV) |
| 4.2 | Driving direction (G251) |  |
| 4.3 | Output speed 1 (G195) III) |  |
| 4.4 | Output speed 2 (G196) III) |  |

I) To 1.3: The signal from switch F is sufficient for activating the electromagnet N110.

II) K 3.3, 3.4: Switching over into the tiptronic mode is performed by operating one of the two rocker switches on the steering wheel (when selector lever is in position "D" or "S"). The tiptronic system is active for 8 s. The gearbox returns to the normal automatic operating mode after 8 s. If the switches on the steering wheel are activated once more, this period of time is extended. The time delay of 8 s when cornering (exceeding the value of G251 - the transversal acceleration senders), engine braking or when driving under full load, is cancelled.

III) The gearbox control unit determines the vehicle speed and the driving direction from the signals of the senders G195 and G196. The ESP control unit uses the driving speed and the driving direction from the CAN bus drive as a replacement signal.

IV) P - Parking  
R - Reverse gear  
N - Neutral  
D - Drive (normal driving)  
S - Drive (sporty driving)  
TT - Tiptronic mode  
PL - Plus (upshift in tiptronic mode)  
MI - Minus (downshift in tiptronic mode)  
RS - intermediate position (selector lever between two stages or gears)  
ER - ERROR (fault)

**Measured value blocks**

| Nbr. | Description |
| --- | --- |
| 5.2 | Enabling the starter closed/open V) |
| 8.1 | Gearbox input speed – (G182) VI) |
| 8.2 | Input speed of shaft 1 – (G501 ) |
| 8.3 | Input speed of shaft 2 – (G502 ) |
| 8.4 | Gearbox input speed – (G195) |
| 10.1 | Accelerator pedal position |
| 10.2 | Kickdown switch closed/open |
| 10.3 | Engine torque |

V) closed - start-up enabled open - start-up disabled

  
The activation of the starter (terminal 50) is only performed in the selector lever position "P" or "N". If the temperature of the gearbox oil (G93) is below -10°C, the start-up is only enabled in the selector lever position "P". At low temperatures, an increase in the driving torque occurs in the clutches. For this reason, enabling the start-up is only allowed in the position "P" (the secure grip secures the vehicle reliably). The control unit J743 transmits the signal P/N via a discrete cable (triggering the start-up of the gearbox) in the control unit J519. The information about the signal P/N is simultaneously received by the control unit J519 via the CAN data bus. The engine start-up is not enabled when there is a fault in the voltage supply for J743, E313, or of the signal P/N as well as the CAN bus.

VI) In the event of a complete signal loss of the sender G182, the switching quality deteriorates. During sporadic signal failures, a fluctuation of the speed may occur. Checking the engaged clutch with the gear shifted in P (G501, G502).

**Measured value blocks (in driving mode)**

| Nbr. | Description | Value range |
| --- | --- | --- |
| 11.1 | Speed of input shaft 1 (G501) | 0 ... 8160 /rpm |
| 11.2 | Nominal torque of clutch K1 | –600 ... 600 Nm |
| 11.3 | Current of clutch valve 1 (N215) | 0 ... 1,53 A |
| 11.4 | Actual pressure of clutch 1 (G193) | –327.68 ... 327.67 bar |
| 12.1 | Speed of input shaft 2 (G502) | 0 ... 8160 /rpm |
| 12.2 | Nominal torque of clutch K2 | –600 ... 600 Nm |
| 12.3 | Current of clutch valve 2 (N216) | 0 ... 1,53 A |
| 12.4 | Actual pressure of clutch 2 (G194) | –327.68 ... 327.67 bar (max. 10 bar) |

G501 – Speed sensor of drive shafte 1  
G502 – Speed sensor of drive shafte 2  
N215 – Pessure regulator valve 1  
N216 – Pessure regulator valve 2  
G193 – Gearbox hydraulic pressure sender 1  
G194 – Gearbox hydraulic pressure sender 2

**Measured value blocks**

| Nbr. | Description |
| --- | --- |
| 16.1 | Path of adjuster for gears 1-3 (G487) VII) |
| 16.2 | Path of adjuster for gears 2-4 (G488) VII) |
| 16.3 | Path of adjuster for gears 5-N (G489) VII) |
| 16.4 | Path of adjuster for gears 6-R (G490) VII) |
| 19.1 | Temperature of gearbox oil (G93) Standard VIII) |
| 19.2 | Temperature in the control unit (G510) IX) |
| 19.3 | Oil temperature of multi-plate clutch (G509) X) |

VII) approx. 8 mm – Adjuster is correctly set

VIII) The sender G93 transmits more accurate values than the sender G510.

IX) The sender G510 serves mainly for checking the validity of the signal of sender G93.

X) At a temperature (G93) higher than 138°C, the mechatronic control unit J743 triggers a reduction in engine torque. Up to a temperature of 145°C, a progressive reduction in engine torque occurs until the engine runs only at idle speed. The multi-plate clutches are then uncoupled, the vehicle is no longer powered.

**Measured value blocks**

| Nbr. | Description |
| --- | --- |
| 20.1 | Desired gear |
| 20.2 | Currently engaged gear |
| 20.3 | Information about the engaged gear in the instrument panel |
| 54.1 | Identification of the mechatronics |
| 64.1 | Number of values exceeded (170 °C) XI) |
| 64.2 | Number of warnings (160 °C) XI) |
| 80 | Identification of the control unit |
| 81 | Identification of the control unit |
| 82 | Identification of the control unit |
| 84 | Manufacturing date of the gearbox and gearbox code. |

XI) Value of sender G509 - sensor for oil temperature in the multi-plate clutch. When reaching an oil temperature of 160°C, the safety function is then activated and the clutches pulsate, which is perceived in the vehicle as a strong jerk (warning jerk). When reaching 170 °C, the clutches disengage. Sporadic signal failures can result in harsh shifting or skipping gears. As of MY 2013, the sender G509 is no longer present and the temperature is recalculated.

**Measured value blocks – Temperature of the gearbox oil**

| Nbr. | Description |
| --- | --- |
| 109.1 | Total mileage travelled in kilometres |
| 140.1 | Oil temperature \<90°C |
| 140.2 | Oil temperature >=90°C – \<110°C |
| 140.3 | Oil temperature >=110°C – \<120°C |
| 140.4 | Oil temperature >=120°C – \<130°C |
| 141.1 | Oil temperature >=130°C – \<140°C |
| 141.2 | Oil temperature >=140°C |
| 141.3 | Maximum temperature value is reached |

The time intervals, during which the oil temperature moves within the specific temperature ranges, are recorded in the blocks 140.x.

## Printout of the environmental conditions for the last two faults stored in the event memory

All collision values from the measured value blocks are stored in the fault memory. The printout of the environmental conditions is also stored for the **last** as well as the **second last** recorded faults. An example of a printout for the environmental conditions from the fault memory is provided below.

Printout **of the environmental conditions** when the **last** fault was recorded:

![Printout of the environmental conditions for the last two faults stored in the event memory](https://catalog.polo.blue/instructions/ssp-094/f83f247263000d4f.webp)

Printout **of the environmental conditions** when the **second last** fault was recorded:

![Printout of the environmental conditions for the last two faults stored in the event memory](https://catalog.polo.blue/instructions/ssp-094/d814b3febc038ff1.webp)
