# Faults of the gearbox 0AM and their rectification – SSP 094 Diagnosis of the automatic gearboxes 0AM and 02E

> Common 0AM faults, from jerking at start-up to gears that do not shift: assessment, cause and solution with its TPI number.

- Web page: https://catalog.polo.blue/self-study/ssp-094-diagnosis-of-the-automatic-gearboxes-0am-02e/faults-0am/
- Original document (PDF): https://cdn.polo.blue/files/SSP-094-Diagnosis-of-the-automatic-gearboxes-0AM-and-02E.pdf

## List of common faults

- 1a. – Vehicle does not run, gearbox control unit without communication.
- 2a. – Uncomfortable sensation during start-up (jerking when starting up), fault in the event memory P0841 02115X or 02113 sender 1 of hydraulic pressure, gearbox - signal invalid.
- 3a. – Metal noise when driving over bumps, memory without faults, SW less than 21xx.
- 4a. – Some gears do not shift, faults will be entered in the event memory.
- 5a. – Uncomfortable sensation during start-up (jerking during acceleration, especially if going uphill or under load).
- 6a. – Uncomfortable sensation during start-up or when accelerating, SW 21xx and higher, event memory without faults, clutches O.K. according to MVB.
- 7a. – Uncomfortable sensation when accelerating, in 2nd gear at low speed, SW 21xx and higher, event memory without faults, clutches O.K. according to MVB.
- 8a. – Delayed upshifting and poor operation of the cruise control on the 1.6 TDI CR 77 kW.
- 9a. – Noise coming from the gearbox, 6th gear cannot be shifted, fault P073B.
- 10a. – The display of the gears flashes, the vehicle does not run.
- 11a. – The display of the gears lights up, the vehicle does not run.
- 12a. – The gear(s) does/do not shift.
- 13a. – The gears do not shift, the display of the gears flashes.

## Faults after replacing the components

- 1b. – After replacing the mechatronics, the basic setting cannot be performed, it is not possible to shift into any gears.
- 2b. – After replacing the clutches, the basic setting cannot be performed, it is not possible to shift into any gears, clutch is outside the tolerance.

> **Important**
>
> The consequences of the faults on the vehicle and the diagnostic results must always be fully assessed in their context. If the focus is only on the event memory, it can result in an incorrect procedure for repairing.

## 1a. The vehicle does not run, gearbox control unit without communication.

**Assessment:**

- In the event memory: P0562 / 21148 Supply voltage for the engine too low P177F / 21065 Excessive voltage drop of hydraulic pump motor P175F / 21098 Basic setting of the gearbox not performed P189C / 21247 The diagnosis of the pressure increase cannot be carried out P174A / 21108 Valve 3 in the gearbox part, electrical fault or automatic gearbox control unit without communication
- In other control units, faults in the communication with the gearbox control unit (mechatronics)

**Cause:**

**It is an internal fault of the mechatronics - short circuit in the power supply part. This fault occurs on vehicles with mechatronics manufactured up to 01.06.2011.**

**Solution:**

**TPI 2023768** (Replacing the mechatronics, checking/replacing the fuse SB2/SB5)

## 2a. Uncomfortable sensation during start-up. Jerking during start-up.

**Assessment:**

- SW of the control unit of the automatic gearbox 21xx, or lower.
- In the event memory: P0841 02115X or 02113 sender 1 of hydraulic pressure, gearbox - signal invalid.

**Cause:**

**The cause of the fault is a slow oil pressure build-up after the ignition is switched on.**

**Solution:**

**TPI 2027607** (Updating the SW of the automatic gearbox control unit using the so-called Action Code)

## 3a. Metal noise when driving over bumps in 2nd gear.

**Assessment:**

- Metal noise at slow speed when driving over bumps
- No faults are stored in the event memory
- SW of the automatic gearbox control unit lower than 21xx

**Cause:**

**This is caused by the excitation of oscillations when upshifting into the 3rd gear**

**Solution:**

**TPI 2027607 **(Updating the SW of the automatic gearbox control unit to SW 21 xx and higher using the action code). The SW 21xx and higher receives the ABS signal indicating when the vehicle drives over bumps, thereby the mechatronic system disengages the 3rd gear and activates the clutch K1. Thus, damping force is applied in response to the shocks**. **The 3rd gear is then only shifted at the time when it is necessary**.**.

## 4a. Gears are not shifted.

**Assessment:**

- Some gears are not shifted
- The vehicle does not run and the display of the selector lever flashes.
- In the event memory: Gear X cannot be shifted

**Cause:**

**Carry out a test of the speed for the input shafts (MVB 5.3 and 5.4) at idling speed in P and N modes. The input shafts must not rotate. However, if they rotate, check the positions of the adjuster for the clutches (MVB 91 and 111), they must be a min. of 2 mm below the engagement point when in the P mode (otherwise the mechatronics is defective).**

## If the following is entered in the event memory:

**P189A/21186 clutch 1 – insufficient play P073F/21086 unsuccessful synchronisation of the 1st gear P072C/21066 1st gear cannot be engaged**

**Solution:**

**TPI 2025571 **(Replacing the clutches). This is caused by the insufficient play of clutch K1 due to the clutch engaging too early (this affects vehicles fitted with clutches manufactured in the CW 12/2009)

If the input shafts do not rotate in the P mode and the following is still entered in the event memory: gear x cannot be engaged, remove the mechatronics and check the adjusters of the individual gears for mechanical damage (adjuster jammed = defective gearbox).

## 5a. Uncomfortable sensation during start-up. Jerking during acceleration, especially if going uphill or under load).

**Assessment:**

- Jerking during acceleration or when starting up (not just a single jerk).
- SW of the control unit of the automatic gearbox is 21xx, or higher
- Engine running is O.K.
- One fault is entered in the event memory - one of the clutches has reached the upper tolerance limit or exceeded it and is free of defects, faults

**Solution:**

**TPI 2027607** If no fault is entered in the event memory, perform the basic setting and check once more the fault during the test drive. If the fault is not rectified after performing the basic setting, check the condition of the clutches according to the MVB 95-97 and 115-117. If one of the clutches has nearly reached the wear limit or is below the wear limit for transferring the max. torque, replace the clutches.

## 6a. Uncomfortable sensation during start-up or when accelerating. Jerking.

**Assessment:**

- A single jerk (not several) when starting up or after shifting (sometimes this situation is described by the customer as a delay in the acceleration or as a short-term increase in engine speed with acceleration failure)
- SW of the automatic gearbox control unit 21xx and higher
- Engine running is O.K.
- Condition of the clutches according to MVB 95-97 and 115-117 is O.K.
- No fault is entered or faults are entered in the event memory

**Cause:**

**If the position of the clutch adjuster cannot be changed steplessly, jolts occur i.e. when starting up or when shifting into gears; this may be caused by impurities in the mechatronics leading to an erractic movement of the actuation element of the clutch.**

**Solution:**

**Replacing the mechatronics.**

## 7a. Uncomfortable sensation when accelerating, jerking when accelerating slightly in the 2nd gear at low engine speed.

**Assessment:**

- Jerks/vibrations when changing gears from 1st to 2nd gear (always repeated jolts, not just a single jolt)
- Jerks and vibrations at low speeds or when accelerating slightly from approx. 1200 to 2000 rpm in 2nd gear
- Engine running is O.K.
- Condition of the clutches according to MVB 95-97 and 115-117 is O.K.
- No faults are stored in the event memory

**Cause:**

**Uneven power transmission of clutch K2 (change of friction coefficient) when engaging and disengaging the clutch K2**

**Solution:**

**TPI 2028367 **Replacing the clutch set (using the clutch set see TPI, not according to the company ETKA).

## 8a. Delayed upshifting and poor operation of the cruise control on the 1.6 TDI CR 77 kW.

**Assessment:**

- When driving slowly on a slope (most often in parking garages) the vehicle changes late from the 1st into the 2nd gear
- When activating the cruise control with the SET button (most often at about 140 km/h), the vehicle downshifts two gears, the cruise control remains active and the vehicle operates at high speed
- The fault can be detected even after replacing the mechatronics

**Cause:**

- **Fault of the SW of the automatic gearbox control unit.**

**Solution:**

**TPI 2028079** (Updating the SW of the automatic gearbox control unit using the so-called Action Code)

## 9a. Noise coming from the gearbox, 6th gear cannot be shifted, fault P073B.

**Assessment:**

- Noise coming from the gearbox
- 6th gear cannot be shifted
- After switching off and on the ignition, the gearbox is O.K.
- The following is stored in the event memory: P073B – 6th gear cannot be engaged, invalid signal

**Cause:**

- **Fault of the SW of the automatic gearbox control unit.**

**Solution:**

Online updating of the SW of the automatic gearbox control unit (on SW 26xx, or 34xx)

## 10a. The display of the gears flashes, the vehicle does not run.

**Assessment:**

- The display of the gears flashes
- The vehicle does not run
- The following is stored in the event memory: 

  
21062/21184 - P175 clutch 1 switches off inadvertently 21063/21185 – P176E clutch 2 switches off inadvertently 21094/21095 – P072C/D 1st/2nd gear cannot be shifted 21096/21097 – P073A/B 5th/6th gear cannot be shifted

**Cause:**

**Fine impurities in the pressure control valves of the mechatronic control unit**

**Solution:**

**TPI 2027598** (Replacing the mechatronics)

## 11a. The display of the gears lights up, the vehicle does not run.

**Assessment:**

- The display of the gears lights up.
- The vehicle does not run
- The following is stored in the event memory:

  
P072B/21073 Number of authorised attempts for changing the R gear was exceeded P2789/10121 Path 4 of clutch 2 is too short P1899/21265 Function of clutch 2 is limited

**Cause:**

**The path of the plunger for clutch K2 is too short. This applies to vehicles fitted with a clutch manufactured up to 25.05.2009.**

**Solution:**

**TPI 2025592 **(Basic setting and drive for adapting the clutch, if the fault persists, replace the clutch set).

## 12a. Certain gears cannot be shifted.

**Assessment:**

- Initially sporadic, at a later stage the display of the gears remains lit
- Noise while shifting
- The vehicle does not run (initially sporadic)
- The following fault(s) is/are stored: P173A – Transducer 1, paradoxical signal P173B – Transducer 2, paradoxical signal P173C – Transducer 3, paradoxical signal

**Cause:**

**Metal shavings on the magnets for holding the positions of the adjuster/adjusters of the gears. This applies to gearboxes manufactured up to 08.10.2008.**

**Solution:**

**TPI 2026829 **(Replacing the gearbox).

## 13a. Certain gears cannot be shifted, the display of the gears flashes.

**Assessment:**

- The vehicle does not shift into another gear
- The display of the gears flashes
- Vibrations/jerks while driving
- Sometimes the vehicle does not start
- The following fault is stored in the event memory: P171BF 2127X, or 1538 – Play protection for hydraulic pump

**Cause:**

**Internal fault of the mechatronics, this applies to mechatronics manufactured up to CW 45/2010.**

**Solution:**

**TPI 2024664** (Replacing the mechatronics)

## Faults after replacing the components

## 1b. After replacing the mechatronics, the basic setting cannot be performed.

**Assessment:**

- After replacing the mechatronics, the basic setting cannot be performed and it will be completed with a fault code
- The following fault is shown in the event memory: upper limit of clutch tolerance is reached
- The following fault is shown in the event memory: e.g. gear x cannot be shifted, it is not adjustable

**Recommendation:**

- Inspecting the plastic cap on the actuation element for clutches (the cap can be torn off or is lost when using an incorrect tool or during a negligent installation)
- Inspecting the correct seating of the clutch adjuster. If the clutch adjuster is not located in the correct position, one of the clutches may be partially coupled, for this reason, the input shaft is engaged (check the speed according to the MVW 5. 3 and 5. 4)
- If the mechatronics is removed, reset the correct positions of the gear adjusters on the mechatronics (25 mm) as well as the neutral position of the actuation elements of the gears on the gearbox. Then install the mechatronics

## 2b. Delayed upshifting and poor operation of the cruise control on the 1.6 TDI CR 77 kW.

**Assessment:**

- After replacing the clutches the basic setting cannot be performed, it will be completed with a fault code
- The following fault is stored in the event memory: gear x cannot be shifted

**Causes and recommendations:**

- Preset clutch set (the clutches are coupled permanently); as a result of an impact on the clutch set when installing the complete gearbox in the vehicle (in MVB 5. 3 and 5. 4, the speed of the input shafts can also be detected in the position P), in this case the assembly of a new clutch set is required!
- Miscalculating the washers for the clutches. If incorrect washers are used, the new clutch may be irreversibly damaged. It is necessary to perform a new measurement and calculation or to carry out the installation of a new clutch set.
- Inspecting the plastic cap on the actuation element for clutches (the cap can be torn off or is lost when using an incorrect tool or during a negligent installation). Reinstall the plastic cap.
- Inspecting the correct seating of the clutch adjuster. If the clutch adjuster is not located in the correct position, one of the clutches may be partially coupled, for this reason, the input shaft is engaged (check the speed according to the MVW 5. 3 and 5. 4). Correctly position the adjusters.
