# 1.3 Removing and installing Hall sender G40 – 1.6 TDI CR engine (EA189)

> Removing and installing Hall sender G40, 1.6 TDI (Glow plug system) on the VW Polo 6R: 13 steps and 3 drawings. 2 versions of tensioning roller are fitted.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/28-glow-plug-system/removing-and-installing-hall-sender-g40/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 28 – Glow plug system, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [1.2 Checking glow plugs](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/28-glow-plug-system/checking-glow-plugs/index.md)
- Next procedure: [1.4 Removing and installing engine speed sender G 28](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/28-glow-plug-system/removing-and-installing-engine-speed-sender-g-28/index.md)

**Removing**

- Remove engine cover panel [⇒ 3 Engine cover panel](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/).
- Remove fuel filter with bracket ⇒ Rep. gr. 20; Fuel filter; Removing and installing fuel filter.
- Remove poly V-belt [⇒ 13 – Crankshaft group](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/).

- Remove front right wheel housing liner.
- Remove vibration damper [⇒ 1.4 Removing and installing vibration damper](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-and-installing-vibration-damper/#t94-231).

**Polo**

- Remove engine bracket [⇒ 1.8.4 Removing and installing engine bracket, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-and-installing-engine-bracket/#t112-82).

**Continued for all vehicles**

During further work, toothed belt must be removed from idler roller and high-pressure pump.

> **Note**
>
> 2 versions of tensioning roller are fitted. They are not interchangeable. On making adjustments, first check which tensioning roller is fitted [⇒ 2.2 Removing and installing toothed belt](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-toothed-belt/#t190-82).

Removing toothed belt from idler roller and high-pressure pump [⇒ 2.2 Removing and installing toothed belt](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-toothed-belt/#t190-82).

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/006e2899ef9abc0d.webp)

- Disconnect connector -1- for Hall sender - G40- and pull connector out of retainer.
- Detach plug from its retainer.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/ef0c539109ab34e7.webp)

- Unscrew Hall sender - G40- -arrow-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/2f2fe44039405b6e.webp)

- Remove webs and repair aperture cover -arrows- with a screwdriver.
- Remove Hall sender - G40- from cylinder head and guide its plug through repair aperture in toothed belt guard.

**Installing**

Install in reverse order. During this procedure, observe the following:

- Seal repair aperture in toothed belt guard with rubber plugs as specified in ⇒ Electronic Parts Catalogue (ETKA).

- Fit toothed belt and adjust valve timing [⇒ 2.2 Removing and installing toothed belt](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-toothed-belt/#t190-82).

**Polo**

- Install engine bracket [⇒ 1.8.4 Removing and installing engine bracket, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-and-installing-engine-bracket/#t112-82).
