# 1.1 Removing and installing glow plug – 1.6 TDI CR engine (EA189)

> Removing and installing glow plug, 1.6 TDI (Glow plug system) on the VW Polo 6R: 18 steps, special tools 3220 and 3314, tightening torques and 8 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/28-glow-plug-system/removing-and-installing-glow-plug/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 28 – Glow plug system, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [4.5 Cleaning exhaust gas recirculation system](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/26-exhaust-system/cleaning-exhaust-gas-recirculation-system/index.md)
- Next procedure: [1.2 Checking glow plugs](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/28-glow-plug-system/checking-glow-plugs/index.md)

Special tools and workshop equipment required

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/8a3e9361870bdcd5.webp)

- 10 mm jointed spanner - 3220-

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/1783f5bd1b42221a.webp)

- Pliers - 3314-

**Removing**

- Switch off ignition.
- Remove engine cover panel [⇒ 3 Engine cover panel](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/).
- Remove noise insulation at injectors.
- Clean glow plug channel in cylinder head; make sure no dirt gets into cylinder.

> **Note**
>
> - Cleaning procedure:
> - Use a vacuum cleaner to remove coarse dirt.
> - Spray brake cleaner or suitable cleaning agent into glow plug opening, let it work in briefly and blow out with compressed air.
> - Then clean glow plug opening using a cloth moistened with oil.

> **Caution**
>
> Make sure that no wiring connections are damaged when disconnecting the heater-element connectors.

Otherwise the whole wiring harness will need to be renewed.

Do not squeeze the pliers - 3314- too firmly when pulling off glow plug connectors, because otherwise the support sleeve may be damaged.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/2be5c203d78b8359.webp)

- Pull connector -B- off pressure differential sender - G 505- and fuel pressure sender - G 247- -C-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/4542daf7b758903c.webp)

- Open cable guide fasteners to free wiring harness.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/9cb8c6ac1d337413.webp)

- Position pliers - 3314- with groove -arrow A- on support sleeve shoulder -arrow B- and pull plugs off glow pin plugs.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/4a48a58797b07719.webp)

- Carefully pull connector off glow plug in direction of -arrow-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/1ea1c3606f0c67aa.webp)

- Unscrew securing nut of fuel return line from intake manifold, open clamp -arrow- and pull line off fuel rail.
- Remove entire fuel return line and set it down in front of intake manifold.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/8a3e9361870bdcd5.webp)

- To loosen glow plugs use special tool U/J extension and 10 mm socket - 3220-

**Installing**

- To tighten glow plugs use special tool U/J extension and 10 mm socket - 3220- with a suitable torque wrench.
- Then tighten glow plugs to specified torque.

- Specified torque is 18 Nm

- Fit glow plug connectors onto glow plugs and ensure they are properly seated.
- Open cable guide fasteners to free wiring harness.
- Secure wiring harness in cable guide again.
- Continue installation in reverse order of removal.
- Clear engine control unit event memory.

## Tightening torques on this page

### In the steps
| Step | Torque |
| --- | --- |
| Specified torque is 18 Nm | 18 Nm |
