# 3.2 Removing and installing parts of exhaust gas temperature regulation – 1.6 TDI CR engine (EA189)

> VW Polo 6R, step by step: removing and installing exhaust gas temperature senders – 15 steps, special tool T10395, tightening torques and 17 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/26-exhaust-system/removing-and-installing-exhaust-gas-temperature-senders/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 26 – Exhaust system, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [3.1 Assembly overview – exhaust gas temperature regulation](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/26-exhaust-system/assembly-overview-exhaust-gas-temperature-regulation/index.md)
- Next procedure: [4.1 Assembly overview – exhaust gas recirculation](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/26-exhaust-system/assembly-overview-exhaust-gas-recirculation/index.md)

[⇒ 3.2.1 Removing and installing exhaust gas temperature sender 1 G235 ](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/26-exhaust-system/removing-and-installing-exhaust-gas-temperature-senders/#t519-308)

[⇒ 3.2.4 Removing and installing exhaust gas temperature sender 4 G648, Polo LHD vehicles](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/26-exhaust-system/removing-and-installing-exhaust-gas-temperature-senders/#t524-360)

[⇒ 3.2.5 Removing and installing exhaust gas temperature sender 3 G495, Polo LHD vehicles](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/26-exhaust-system/removing-and-installing-exhaust-gas-temperature-senders/#t525-585)

[⇒ 3.2.6 Removing and installing exhaust gas temperature sender 3 G 495, Polo RHD vehicles](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/26-exhaust-system/removing-and-installing-exhaust-gas-temperature-senders/#t527-401)

[⇒ 3.2.7 Removing and installing exhaust gas temperature sender 4 G 648, Polo RHD vehicles](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/26-exhaust-system/removing-and-installing-exhaust-gas-temperature-senders/#t528-258)

## 3.2.1 Removing and installing exhaust gas temperature sender 1 - G235-

**Removing**

- Separate electrical connector -3- for exhaust temperature sender 1 - G235- and move electrical wire aside.
- Remove noise insulation:
  Polo ⇒ General body repairs, exterior; Rep. gr. 50; Noise insulation; Assembly overview - noise insulation

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/6ba56866f45f978a.webp)

> **Note**
>
> You access the threaded connection from above using the spanner from tool set - T10395/7-.

- Unscrew exhaust temperature sender 1 - G235- -item 1- from exhaust manifold.

> **Note**
>
> - Arrows- can be disregarded.

**Installing**

Install in reverse order of removal, observing the following.

> **Note**
>
> - Coat threads of exhaust temperature sender with high-temperature paste ⇒ Electronic Parts Catalogue (ETKA).
> - Fit all cable ties in the original position when installing.

Installation position of exhaust gas temperature sender -G235-.

> **Warning**
>
> The torque wrench - V.A.G 1331- must be set to 28 Nm in this case.

Extending the torque wrench - V.A.G 1331- with the spanner from tool set - T10395/7- allows the correct torque of 45 Nm to be achieved.

Lubricate thread of sender using high-temperature paste - G 052 112 A3-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/266f7cbd186d5bbf.webp)

- Screw exhaust gas temperature sensor 1 - G 235- in by hand.
- Then apply tightening torque using torque wrench - V.A.G 1331- together with wrench from tool set - T10395/7-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/ffcd2751ba76b8f0.webp)

- Angled shaft must have a distance -a- = 3 … 5 mm to bolting of turbocharger support.

## 3.2.4 Removing and installing exhaust gas temperature sender 4 - G648-, Polo LHD vehicles

Special tools and workshop equipment required

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/a3243c0e3d753c7f.webp)

- Tool insert, AF 17 mm - T10395- 

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/ff1b1e66dda21957.webp)

**Removing**

- Separate electrical connector -2- for exhaust temperature sender 4 - G648- and move electrical wire aside.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/042b4d9fbd6b9efe.webp)

> **Note**
>
> - Items 1 and 3- can be disregarded.
> - Unscrew exhaust gas temperature sender 4 - G648- -item 1- using tool from 17 mm tool set - T10395-.

> **Note**
>
> Disregard -item 2-.

**Installing**

Install in reverse order of removal, observing the following.

- Specified torque.

> **Caution**
>
> Loose exhaust gas temperature senders cause malfunctions.
>
> - Threads of exhaust gas temperature sender -G495- and - G648- are coated. Do NOT additionally coat with hightemperature paste and always adhere to the prescribed specified torque.

## 3.2.5 Removing and installing exhaust gas temperature sender 3 - G495-, Polo LHD vehicles

Special tools and workshop equipment required 

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/c979c192814bec52.webp)

- Tool insert, AF 17 mm - T10395-

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/711e2303917caa57.webp)

- Torque wrench - V.A.G 1331-

**Removing**

- Remove Lambda probe - G39- [⇒ 6.2 Removing and installing Lambda probe](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/lambda-probe/#t442-82).
- Separate electrical connector -1- for exhaust temperature sender 3 - G495- and move electrical wire aside.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/7e07f95271da409b.webp)

- Unscrew exhaust gas temperature sender 3 - G495- -item 1- using tool from 17 mm tool kit - T10395-.

> **Note**
>
> - Items 2 and 3- can be disregarded.

**Installing**

Install in reverse order of removal, observing the following.

> **Note**
>
> Fit all cable ties in the original position when installing.

> **Caution**
>
> Loose exhaust gas temperature senders cause malfunctions.
>
> - Threads of exhaust gas temperature sender -G495- and - G648- are coated. Do NOT additionally coat with hightemperature paste and always adhere to the prescribed specified torque.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/53235178fb1a21fe.webp)

Installation position of temperature sender -G495- -item 1-:

- Angled end facing left side of vehicle.
- Angle -α- to mark -arrow- = approx. 17°.

> **Warning**
>
> The torque wrench - V.A.G 1331- must be set to 29 Nm in this case.

Extending the torque wrench - V.A.G 1331- with the spanner from tool set - T10395/6- allows the correct torque of 45 Nm to be achieved.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/04692d998b65c68a.webp)

- Screw exhaust temperature sender 1 - G 495- in by hand.
- Then apply tightening torque using torque wrench - V.A.G 1331- together with wrench from tool set - T10395/6-.

## 3.2.6 Removing and installing exhaust gas temperature sender 3 - G 495-, Polo RHD vehicles

Special tools and workshop equipment required

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/80da8ddb7bc2c8c6.webp)

- Torque wrench - V.A.G 1331-

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/21167a891fea0c0a.webp)

- Tool set - T10395- 

Specified torque for exhaust temperature sender 3 - G 495- upstream of particulate filter (right-hand drive)

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/1e84c4f0735b598f.webp)

Use torque wrench - V.A.G 1331- with spanner from tool set - T10395/6- to tighten.

> **Warning**
>
> The torque wrench - V.A.G 1331- must be set to 29 Nm in this case.

Extending the torque wrench - V.A.G 1331- with the spanner from tool set - T10395/6- allows the correct torque of 45 Nm to be achieved.

## 3.2.7 Removing and installing exhaust gas temperature sender 4 - G 648-, Polo RHD vehicles

Special tools and workshop equipment required

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/35d6d5ff8c7dae62.webp)

- Torque wrench - V.A.G 1331-

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/c979c192814bec52.webp)

- Tool set - T10395- 

Specified torque for exhaust temperature sender 4 - G 648- downstream of particulate filter

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/0d88bfd5e7bb912a.webp)

Use torque wrench - V.A.G 1331- with spanner from tool set - T10395/6- to tighten.

> **Warning**
>
> The torque wrench - V.A.G 1331- must be set to 29 Nm in this case.

Extending the torque wrench - V.A.G 1331- with the spanner from tool set - T10395/6- allows the correct torque of 45 Nm to be achieved.

## Tightening torques on this page

### 3.2.1 Removing and installing exhaust gas temperature sender 1 - G235- [To the steps](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/26-exhaust-system/removing-and-installing-exhaust-gas-temperature-senders/#3-2-1-removing-and-installing-exhaust-gas-temperature-sender)
| Step | Torque |
| --- | --- |
| The torque wrench - V.A.G 1331- must be set to 28 Nm in this case. | 28 Nm |
| Extending the torque wrench - V.A.G 1331- with the spanner from tool set - T10395/7- allows the correct torque of 45 Nm to be achieved. | 45 Nm |

### 3.2.5 Removing and installing exhaust gas temperature sender 3 - G495-, Polo LHD vehicles [To the steps](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/26-exhaust-system/removing-and-installing-exhaust-gas-temperature-senders/#3-2-5-removing-and-installing-exhaust-gas-temperature-sender)
- 3.2.6 Removing and installing exhaust gas temperature sender 3 - G 495-, Polo RHD vehicles [To the steps](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/26-exhaust-system/removing-and-installing-exhaust-gas-temperature-senders/#3-2-6-removing-and-installing-exhaust-gas-temperature-sender)
- 3.2.7 Removing and installing exhaust gas temperature sender 4 - G 648-, Polo RHD vehicles [To the steps](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/26-exhaust-system/removing-and-installing-exhaust-gas-temperature-senders/#3-2-7-removing-and-installing-exhaust-gas-temperature-sender)

| Step | Torque |
| --- | --- |
| The torque wrench - V.A.G 1331- must be set to 29 Nm in this case. | 29 Nm |
| Extending the torque wrench - V.A.G 1331- with the spanner from tool set - T10395/6- allows the correct torque of 45 Nm to be achieved. | 45 Nm |
