# 1.2 Aligning exhaust system free of stress – 1.6 TDI CR engine (EA189)

> Aligning exhaust system free of stress, 1.6 TDI (Exhaust pipes and silencers) on the VW Polo 6R: 7 steps, tightening torques and 5 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/26-exhaust-system/aligning-exhaust-system-free-of-stress/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 26 – Exhaust system, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [1.1 Assembly overview – silencers](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/26-exhaust-system/assembly-overview-silencers/index.md)
- Next procedure: [1.3 Installation position of clamp](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/26-exhaust-system/installation-position-of-clamp/index.md)

[⇒ 1.2.2 Aligning exhaust system free of stress, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/26-exhaust-system/aligning-exhaust-system-free-of-stress/#t479-525)

## 1.2.2 Aligning exhaust system free of stress, Polo

Special tools and workshop equipment required

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/c95120bba0a3e6d0.webp)

- Torque wrench - V.A.G 1331-

**Condition**

- The exhaust system is cold.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/fa8fb2018eb4b078.webp)

**Procedure**

- Loosen threaded connections of the front clamp.
- Align clamp on front exhaust pipe under consideration of dimension -a-. Dimension -a- = 5 mm

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/38c3a8abb5c01c90.webp)

- Align clamp so that bolt ends do not protrude beyond lower edge of clamp -arrow-.
- Tighten front threaded connection of clamp slightly.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/2bdcda2bd5adbe7d.webp)

- Then align exhaust system with mountings under consideration of dimension -a-. -Arrow- points in direction of travel. Dimension -a- = 3 … 7 mm.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/9c534bb99cbf96a9.webp)

- Then evenly tighten securing nuts -arrows- of foremost clamp. Specified torque: M8 = 25 Nm, M10 = 40 Nm.
- Once clamp has been tightened, check set-up dimensions and correct if necessary.

## Tightening torques on this page

### 1.2.2 Aligning exhaust system free of stress, Polo [To the steps](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/26-exhaust-system/aligning-exhaust-system-free-of-stress/#1-2-2-aligning-exhaust-system-free-of-stress-polo)
| Step | Torque |
| --- | --- |
| Then evenly tighten securing nuts -arrows- of foremost clamp. Specified torque: M8 = 25 Nm, M10 = 40 Nm. | 25 Nm / 40 Nm |
