# 5.6 Removing and installing pressure differential sender G505 – 1.6 TDI CR engine (EA189)

> Removing and installing sender G505 (DPF), 1.6 TDI (Senders and sensors) on the VW Polo 6R: 11 steps and 4 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-installing-pressure-differential-sender-g505/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 23 – Mixture preparation - injection, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [5.5 Checking fuel metering valve N 290](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/checking-fuel-metering-valve-n-290/index.md)
- Next procedure: [6 Lambda probe](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/lambda-probe/index.md)

[⇒ 5.6.1 Differentiating criteria](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-installing-pressure-differential-sender-g505/#t432-217)

[⇒ 5.6.3 Removing and installing pressure differential sender G 505, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-installing-pressure-differential-sender-g505/#t435-437)

[⇒ 5.6.4 Removing and installing pressure differential sender G 505, Polo, right-hand drive](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-installing-pressure-differential-sender-g505/#t436-383)

## 5.6.1 Differentiating criteria

> **Note**
>
> - Pressure differential sender - G 505- determines charge status of particulate filter.
> - Different measurement methods are used.
> - The component retains the same designation.

Method 1 (differential-pressure measurement)

Pressure differential sender - G 505- is connected via 2 pipes to the measuring points upstream and downstream of the particulate filter.

Assembly overview - Lambda probe.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/365863b5403432ba.webp)

- **1** Pressure differential sender - G 505- with 2 pipe system
- **2** Exhaust gas feed

Method 2 (relative-pressure measurement)

Pressure differential sender - G 505- is connected via one pipe to the particulate filter.

Assembly overview - lambda probe 

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/27e9b7ad972bf98e.webp)

- **1** Pressure differential sender - G 505- with 1 pipe system
- **2** Fresh air feed

## 5.6.3 Removing and installing pressure differential sender - G 505-, Polo

> **Note**
>
> - Pressure differential sender - G 505- determines charge status of particulate filter.
> - Different measurement methods are used.
> - The component retains the same designation.

Method 1 (differential-pressure measurement)

Pressure differential sender - G 505- is connected via 2 pipes to the measuring points upstream and downstream of the particulate filter.

Assembly overview [⇒ Item 3 (2.1.3 Assembly overview - front exhaust pipe with particulate filter, Polo, left-hand drive)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/26-exhaust-system/assembly-overview-emission-control/#t487-126).

Method 2 (relative-pressure measurement)

Pressure differential sender - G 505- is connected via one pipe to the particulate filter.

**Removing**

- Remove engine cover panel [⇒ 3 Engine cover panel](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/).
- Before pulling off, spray two hoses of pressure differential sender - G 505- with solvent.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/7d279a87cd10c9a9.webp)

- Pull connector -2- from pressure differential sender - G 505-.
- Pull hoses carefully and straight from unions (unions break off pressure differential sender - G 505- very easily).
- Unscrew bolt -3-, remove pressure differential sender - G 505-.

**Installing**

- When installing, note the following:

- Specified torque for pressure differential sender - G 505- bolt, see assembly overview - Lambda probe [⇒ Item 2 (2.1.3 Assembly overview - front exhaust pipe with particulate filter, Polo, left-hand drive)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/26-exhaust-system/assembly-overview-emission-control/#t487-109)

> **Note**
>
> - Before installing, blow out hoses of pressure differential sender - G 505- to particulate filter with compressed air (hoses can become obstructed or may ice up due to condensation).
> - Make sure that hoses are securely fitted and seal properly.

An adaptation must be performed after renewing pressure differential sender - G 505- and/or particulate filter. (The procedure is also described under Guided Functions).

Select correct vehicle in guided fault finding.

## 5.6.4 Removing and installing pressure differential sender - G 505-, Polo, right-hand drive

Pressure differential sender - G 505- is connected via 2 pipes to the measuring points upstream and downstream of the particulate filter.

Assembly overview - Lambda probe [⇒ Item 8 (2.1.4 Assembly overview - front exhaust pipe with particulate filter, Polo, right-hand drive)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/26-exhaust-system/assembly-overview-emission-control/#t489-553).

Pressure differential sender - G 505- determines charge status of particulate filter.

**Removing**

- Before pulling off, spray two hoses of pressure differential sender - G 505- with solvent.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/349c664300c5acdd.webp)

- Pull electrical connector -2- from pressure differential sender - G 505-.
- Pull hoses carefully and straight from unions (unions break off pressure differential sender - G 505- very easily).
- Unscrew nut -1-, remove pressure differential sender - G 505-.

**Installing**

- When installing, note the following:

- Specified torque for pressure differential sender - G 505- bolt, see: Assembly overview - lambda probe [⇒ Item 10 (2.1.4 Assembly overview - front exhaust pipe with particulate filter, Polo, right-hand drive)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/26-exhaust-system/assembly-overview-emission-control/#t489-601)

> **Note**
>
> - Before installing, blow out hoses of pressure differential sender - G 505- to particulate filter with compressed air (hoses can become obstructed or may ice up due to condensation).
> - Make sure that hoses are securely fitted and seal properly.

An adaptation must be performed after renewing pressure differential sender - G 505- and/or particulate filter. (The procedure is also described under Guided Functions).

Select correct vehicle in guided fault finding.
