# 5.1 Removing and installing fuel pressure regulating valve N 276 – 1.6 TDI CR engine (EA189)

> VW Polo 6R (Senders and sensors), step by step: removing, installing fuel pressure valve N276, 1.6 TDI – 16 steps and 1 drawing.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-installing-fuel-pressure-regulating-valve-n276/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 23 – Mixture preparation - injection, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [4.2 Removing and installing high-pressure pump](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-high-pressure-pump/index.md)
- Next procedure: [5.2 Checking fuel pressure regulating valve N276](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/checking-fuel-pressure-regulating-valve-n276/index.md)

Special tools and workshop equipment required

- Torque wrench
- Open jaw insert, 36 mm AF

Fuel pressure regulating valve - N 276- -6- is located on fuel rail.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/96b3da1fec51a942.webp)

It ensures pressure is constant in fuel rail and in injector lines.

If pressure is too high in the fuel high-pressure circuit, fuel pressure regulating valve - N 276- opens.

As a result a small amount of fuel from the fuel rail will make its way back to fuel tank via the return line.

If pressure is too low in fuel high-pressure circuit, fuel pressure regulating valve - N 276- closes.

This seals the high-pressure side against the low-pressure side.

> **Note**
>
> The fuel pressure regulating valve - N 276- cannot be re-used.

> **Caution**
>
> After renewing high-pressure pump, fuel pressure regulating valve - N276- or fuel delivery unit, it is essential to reset learnt values of respective components. Use Guided functions and start »Basic settings; Resetting learnt values« on ⇒ Vehicle diagnostic tester, for this. Otherwise there will be problems in starting the engine.

**Removing**

> **Warning**
>
> - Always observe rules for cleanliness and instructions when working on fuel system [⇒ 3.1 Rules for cleanliness](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/00-technical-data/rules-for-cleanliness/#t12-146).
> - Always follow these rules for cleanliness and instructions before starting work and while working on the fuel system.

- Remove engine cover panel [⇒ 3 Engine cover panel](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/).
- Removing high-pressure accumulator [⇒ 3.6 Removing and installing fuel rail](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-fuel-rail/#t408-590).
- Clean threaded area around fuel pressure regulating valve - N 276- (e.g. with standard cleaning solution) before removing.

Under no circumstances may dirt enter the hole on the fuel rail element (fuel rail).

> **Note**
>
> Do not allow any cleaning agent to get into the connector, clean it carefully.

- Dry fuel pressure regulating valve - N 276-.
- Loosen regulating valve using 36 mm open-end spanner insert. Then unscrew and remove by hand.
- Extract dirt from threads and sealing surfaces. Do not use tools or other instruments for this purpose.

> **Note**
>
> Seal off drilling immediately with a suitable plug to prevent dirt from entering.

**Installing**

> **Note**
>
> - The fuel pressure regulating valve - N 276- has a deformable sealing lip and no separate seal; it can therefore be used only once.
> - Check that sealing surfaces (deformable sealing lip) and threads on new fuel pressure regulating valve - N 276- are not damaged.
> - Check sealing surface of drilling.
> - Lubricate thread and deformable sealing lip of fuel pressure regulating valve - N 276- with Molybdenum grease.

- Screw in fuel pressure regulating valve - N 276- by hand.
- To tighten union nut, use a suitable torque wrench with a 36 mm open-end spanner insert.
- Install fuel rail [⇒ 3.6 Removing and installing fuel rail](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-fuel-rail/#t408-590).

- Specified torque: [⇒ 1.2 Assembly overview - fuel system](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/assembly-overview-fuel-system/#t380-82)

- Check fuel system for leaks.
- Connect vehicle diagnostic tester.
- Read event memory and erase stored event entry if necessary.
- After installation, run engine at moderate speed for several minutes and then switch off.
- Then test drive the vehicle, accelerating to full throttle at least once.
- Then check high-pressure part of fuel system again for leakage.
- Read event memory again.
