# 8.2 Removing and installing intake manifold – 1.6 TDI CR engine (EA189)

> Removing and installing intake manifold, 1.6 TDI on the VW Polo 6R: 19 steps. Otherwise the whole wiring harness will need to be renewed.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-intake-manifold/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 23 – Mixture preparation - injection, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [8.1 Assembly overview – intake manifold](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/assembly-overview-intake-manifold/index.md)
- Next procedure: [8.3 Removing and installing throttle valve module J338](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-throttle-valve-module-j338/index.md)

**Removing**

Special tools and workshop equipment required

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/711e2303917caa57.webp)

- Torque wrench - V.A.G 1331-

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/1783f5bd1b42221a.webp)

- Pliers - 3314-

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/3bc7da55d506148c.webp)

- Multi-point bit - T10405-

**Removing**

[⇒ 2 Safety information](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/00-technical-data/)

[⇒ 3.1 Rules for cleanliness](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/00-technical-data/rules-for-cleanliness/#t12-146)

- Remove engine cover panel [⇒ 3 Engine cover panel](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/).
- Remove noise insulation:
  Polo ⇒ General body repairs, exterior; Rep. gr. 50; Noise insulation; Assembly overview - noise insulation

Removing high-pressure accumulator [⇒ 3.6 Removing and installing fuel rail](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-fuel-rail/#t408-590).

> **Caution**
>
> Make sure that no wiring connections are damaged when disconnecting the connectors. Otherwise the whole wiring harness will need to be renewed. Do not compress the pliers - 3314- too firmly to separate the connectors, otherwise the support sleeve may be damaged.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/b191fc41337f4291.webp)

- Unclip vacuum lines -arrow- and lay to side.

**Polo**

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/32cf1f1f03389cbb.webp)

- Unclip coolant return hose -arrows- and place coolant line to one side.

The arrangement of the coolant return hose can vary.

**Continued for all vehicles**

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/38d009fe0fe62f83.webp)

- Remove securing bolts -arrows-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/c784cc1bc6caecb2.webp)

- Disconnect connector -3- from intake manifold flap motor - V157- (if there is one).

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/af6cd6d26ade3425.webp)

- Pull connector -2- off throttle valve module - J338-.
- Remove bolt -3- from dipstick connection.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/3afdb332014d5ea8.webp)

- Unscrew bolts -arrows-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/06c9158455a7bf92.webp)

- Remove exhaust gas recirculation connecting pipe.
- To do this, open clip -1-.
- Unscrew securing bolts from intake manifold from the outside to the inside in diagonal sequence with socket - T10405-.
- Carefully remove intake manifold.

**Installing**

Install in reverse order, noting the following:

- Specified torque [⇒ 8 Intake manifold](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/)
- Always renew seals.

- Tighten intake manifold bolts from inside outwards, alternately and diagonally.
- Install air pipe.
- Install high-pressure accumulator [⇒ 3.6 Removing and installing fuel rail](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-fuel-rail/#t408-590).

> **Note**
>
> - An intake manifold without an intake manifold flap - V157- ⇒ Electronic Parts Catalogue (ETKA) can also be used as a replacement part.
> - A blanking cap and fastenings are included with the replacement intake manifold ⇒ Electronic Parts Catalogue (ETKA).

**Also use following procedure**

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/0c8aae1f1fcf06d3.webp)

If an intake manifold with intake manifold flap - V157- was installed.

- Cap off now free connector -3- to intake manifold flap motor - V157- using blanking cap.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/1d68a5fbe454ecbd.webp)

- Attach capped connector to wiring harness with cable ties -arrows-.
- Secure loose vacuum line with cable tie -arrow-.
