# 3.5 Removing and installing injectors – 1.6 TDI CR engine (EA189)

> Removing and installing injectors, 1.6 TDI on the VW Polo 6R: 21 steps, special tools T10055, T10377 and T40055, tightening torques and 8 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-injectors/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 23 – Mixture preparation - injection, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [3.4 Check pressure retention valve in fuel return line](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/check-pressure-retention-valve-in-fuel-return-line/index.md)
- Next procedure: [3.6 Removing and installing fuel rail](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-fuel-rail/index.md)

[⇒ 3.5.1 Removing](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-injectors/#t405-82)

[⇒ 3.5.2 Installing](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-injectors/#t406-309) 

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/a7914c8aab5ff17c.webp)

Special tools and workshop equipment required

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/ed4c0e5fb26d3761.webp)

- Puller - T10055-
- Assembly sleeve - T10377-
- Socket - T40055-
- Torque wrench - V.A.G 1331-
- Ratchet wrench - V.A.G 1331/1-
- Support sleeve - T10411-
- Injector remover - T10402- 

## 3.5.1 Removing

- Remove engine cover panel [⇒ 3 Engine cover panel](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/).
- Remove noise insulation from cylinder head cover.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/ebfef2ec8b6fce6c.webp)

- Pull off connectors -1- at injectors to be removed.

Remove high-pressure line between fuel rail and injectors. [⇒ 3.7 Removing and installing high-pressure lines](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-high-pressure-lines/#t412-380)

> **Note**
>
> - Open the return line connection with a narrow screwdriver and long-nosed pliers.
> - Renew clips.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/83b6bd9cbb90d0f1.webp)

- To release fuel return line, pull clip out in direction of arrow.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/a0c297110cddbb61.webp)

- Pull fuel return line connections off injectors in direction of arrow.
- Unscrew securing bolt of clamping piece of injector to be removed.

> **Caution**
>
> Proceed very carefully to prevent unnecessary dismantling or further damage.

> **Note**
>
> In some vehicles (e.g. Touran), the plenum chamber bulkhead must be removed ⇒ General body repairs, exterior; Rep. gr. 50; Plenum chamber bulkhead; Assembly overview - plenum chamber bulkhead.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/38541d199f59712e.webp)

- Apply puller - T10055- with injector remover - T10402- -1- and -2- as shown in illustration and pull injectors out upwards by tapping gently.

## 3.5.2 Installing

Important instructions for working on fuel system [⇒ 3.1 Rules for cleanliness](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/00-technical-data/rules-for-cleanliness/#t12-146)

**Fitting used injectors**

- Clean empty injector bores and sealing surfaces in cylinder head using cleaning set - VAS 6811- before fitting injectors ⇒ Instructions

When a used injector is re-fitted, the following must be renewed:

- Copper seal
- O-ring for injector shaft
- Retaining clip for injector return
- O-ring for return line

- Spray tip of injector with rust-releasing spray. Wait approx. 5 minutes and wipe off soot particles and oil with a cloth.
- If an injector is very dirty, the tip of the nozzle should also be cleaned with a soft brass wire brush to make it easier to remove the copper seal. Do not apply the wire brush to the bores in the nozzle.

> **Note**
>
> It must be ensured that the brass brush does not touch the holes in the injection nozzles.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/4689de8465537138.webp)

- To remove the old copper seal from the injector, carefully clamp the copper seal in a pair of pliers so it is just prevented from spinning.
- Then carefully pull and twist the injector out of the copper seal by hand.
- Clean off deposits under the copper seal using a suitable scraper.

> **Caution**
>
> Risk of damage to sealing surface for injector.
>
> - To remove carbon deposits from the injector sealing surface, clean the injector shaft in the cylinder head with a cloth soaked in engine oil or rust solvent.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/c44168335588d301.webp)

- Fit renewed clips before fitting the injector. To do this, grease lightly.

Fitting new injectors:

When a fitting a new injector, the following must be renewed:

- Copper seal
- O-ring for injector shaft
- O-ring for injector return line
- Retaining clip for injector return

Continuation for used and new injectors:

- Use a plastic socket to mount new copper seal.
- Lubricate all O-rings with engine oil or assembly oil before installing.
- Fit new O-rings for injector shaft.
- Push clamping piece onto injectors and pay attention to installation position.
- Always guide two injectors in pairs carefully into injector bores in cylinder head.
- Tighten bolt for clamp to a maximum of only 1 to 2 Nm at first.

- Injectors must still be able to move.

- Install high-pressure lines [⇒ 3.7 Removing and installing high-pressure lines](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-high-pressure-lines/#t412-380).

Further assembly in reverse order of removal.

- Tighten injectors [⇒ 1.2 Assembly overview - fuel system](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/assembly-overview-fuel-system/#t380-82)

After renewing one or more injectors:

- Write adapted correction values for new injectors into engine control unit [⇒ 3.2 Adapting correction values for injectors](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/adapting-correction-values-for-injectors/#t399-515).
- Reset learnt values of fuel pressure regulating valve - N276-.
- 01 - Engine electronics
- 01 - Engine electronics functions

| 01 - Reset adaptation values of engine ctrl. mod- |
| --- |
| ule |

| Selection: Reset learnt values of dosing unit and |
| --- |
| pressure regulating valve |

## Tightening torques on this page

### 3.5.2 Installing [To the steps](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-injectors/#3-5-2-installing-2)
| Step | Torque |
| --- | --- |
| Tighten bolt for clamp to a maximum of only 1 to 2 Nm at first. | 2 Nm |
