# 4.2 Removing and installing high-pressure pump – 1.6 TDI CR engine (EA189)

> VW Polo 6R, step by step: removing and installing high-pressure pump, 1.6 TDI – 19 steps, special tool T10051, tightening torques and 15 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-high-pressure-pump/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 23 – Mixture preparation - injection, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [4.1 Assembly overview – high-pressure pump](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/assembly-overview-high-pressure-pump/index.md)
- Next procedure: [5.1 Removing and installing fuel pressure regulating valve N 276](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-installing-fuel-pressure-regulating-valve-n276/index.md)

> **Caution**
>
> Danger of functional impairment due to contamination/soiling

To prevent the high-pressure fuel pump from running while it is empty (very tight tolerances) and to ensure that the engine starts quickly after parts have been renewed, it is important to observe the following:

- If the high-pressure pump is removed or renewed, the fuel system must be bled before engine is started for the first time.

Initial fuel filling procedure [⇒ 1.3 Filling/bleeding fuel system](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/filling-bleeding-fuel-system/#t392-82).

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/85a8a9a8e2c59d60.webp)

Special tools and workshop equipment required

- Counter-hold tool - T10051-
- Puller - T40064-
- Thrust piece - T40064/1-
- Torque wrench - V.A.G 1331-

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/d697b4abe84c0c33.webp)

- Pliers - 3314- 

> **Caution**
>
> After renewing high-pressure pump, fuel pressure regulating valve - N276- or fuel delivery unit, it is essential to reset learnt values of respective components. Use Guided functions and start »Basic settings; Resetting learnt values« on ⇒ Vehicle diagnostic tester, for this. Otherwise there will be problems in starting the engine.

**Removing**

- Remove toothed belt from camshaft and high-pressure pump [⇒ 2.2 Removing and installing toothed belt](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-toothed-belt/#t190-82).

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/78514fd34ee41819.webp)

- Position pliers - 3314- with groove -arrow A- on support sleeve shoulder -arrow B- and pull plugs off glow pin plugs.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/e8c3ae5ff8e93d74.webp)

- Carefully pull connector off glow plug in direction of -arrow-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/5191d1d45c3d09c0.webp)

- Separate connector -1- from fuel temperature sender - G81-.

**Polo **

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/22f3d97d541aadca.webp)

- Unclip coolant return hose -arrows- and place coolant line to one side.

2) There are different installation positions for the coolant return hose.

**Continued for all vehicles**

> **Caution**
>
> Make sure that no wiring connections are damaged when disconnecting the connectors. Otherwise the whole wiring harness will need to be renewed. Do not compress the pliers - 3314- too firmly to separate the connectors, otherwise the support sleeve may be damaged.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/00ba3db7677dab0c.webp)

- Pull fuel supply line -arrow- off the high-pressure pump.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/17d2df57e6dbe65a.webp)

- Unscrew -1, 3, 4-. Separate connector -arrow- from fuel metering valve - N290-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/3a3ca60ceb7156ae.webp)

- Unscrew bolts -4- and then remove bracket.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/ca4c80b95a172383.webp)

- Pull off fuel return line -2-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/fce524c634132b83.webp)

- Remove high-pressure fuel line between high-pressure pump and high-pressure accumulator [⇒ Item 12 (1.2.1 Assembly overview - fuel system, Polo)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/assembly-overview-fuel-system/#t382-234).
- Take toothed belt off high-pressure pump [⇒ 2.2 Removing and installing toothed belt](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-toothed-belt/#t190-82).

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/8f3ec33a80a96e5d.webp)

- Counterhold hub of high-pressure pump using counterhold - T10051- and unscrew securing nut -1-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/06e16ced759915d0.webp)

- Apply puller - T40064- with thrust piece - T40064/1- and pin - T40064/2- as shown in illustration and pull hub off high-pressure pump. If necessary, counterhold with a 24 mm open-end spanner.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/383d23ad64e01ee9.webp)

- Unscrew securing bolts -arrows- for high-pressure pump.
- Remove high-pressure pump.

**Installing**

Install in reverse order. Specified torques for fuel system [⇒ 1.2.1 Assembly overview - fuel system, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/assembly-overview-fuel-system/#t380-158)

Specified torque for toothed belt drive, Polo [⇒ 2.1.2 Assembly overview - toothed belt, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/assembly-overview-toothed-belt/#t187-309)

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/152f3df928a87327.webp)

Specified torques -1, 3, 4-

In illustration 1 = 8 Nm

In illustration 3 = 8 Nm

In illustration 4 = 20 Nm

- Connect vehicle diagnostic tester.
- Read event memory and erase stored event entry if necessary.
- Filling/bleeding high-pressure pump/fuel system [⇒ 1.3 Filling/bleeding fuel system](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/filling-bleeding-fuel-system/#t392-82).
- Perform the function “Resetting engine control unit programmed values” in “Guided functions”.

## Tightening torques on this page

### In the steps
| Step | Torque |
| --- | --- |
| In illustration 1 = 8 Nm | 8 Nm |
| In illustration 3 = 8 Nm | 8 Nm |
| In illustration 4 = 20 Nm | 20 Nm |
