# 3.7 Removing and installing high-pressure lines – 1.6 TDI CR engine (EA189)

> VW Polo 6R, step by step: removing and installing high-pressure lines, 1.6 TDI – 27 steps, special tools V.A.G 1331/1 and V.A.G 1331/6 and 13 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-high-pressure-lines/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 23 – Mixture preparation - injection, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [3.6 Removing and installing fuel rail](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-fuel-rail/index.md)
- Next procedure: [4.1 Assembly overview – high-pressure pump](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/assembly-overview-high-pressure-pump/index.md)

[⇒ 3.7.1 Removing high-pressure lines between fuel rail and injectors](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-high-pressure-lines/#t413-700)

[⇒ 3.7.2 Removing high-pressure line between fuel rail and highpressure pump](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-high-pressure-lines/#t414-537)

[⇒ 3.7.3 Installing high-pressure lines](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-high-pressure-lines/#t415-383)

Special tools and workshop equipment required

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/e4fa9f0ed5ff547e.webp)

- Torque wrench - V.A.G 1331- 

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/e22fd9455949f255.webp)

- Ratchet wrench - V.A.G 1331/1-

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/41792bca7a269606.webp)

- Tool insert 17 mm - V.A.G 1331/6-

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/9c4a67259bf9bbf1.webp)

- Socket - T40055-

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/b4694088051341dd.webp)

- Support sleeve - T10411-

## 3.7.1 Removing high-pressure lines between fuel rail and injectors

- Remove engine cover panel [⇒ 3 Engine cover panel](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/).

> **Caution**
>
> Ensure absolute cleanliness. There should be no dirt in the disconnected fuel return lines or the open connections on the injectors under any circumstances.

Protect open fuel connections from dirt entrainment using suitable methods under all circumstances.

Used injectors may only be re-installed on the same cylinder.

Preferable order for disconnecting high-pressure lines cylinder 4-3-2-1

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/1ee7af85e01df68a.webp)

- To disconnect the high-pressure lines, counterhold the highpressure fitting -A- on the injectors.
- Remove high-pressure line between fuel rail and injectors.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/5315ab7cf6c50846.webp)

- Then only loosen the high-pressure line between fuel rail and high-pressure pump -3-.

## 3.7.2 Removing high-pressure line between fuel rail and high-pressure pump

> **Caution**
>
> Ensure absolute cleanliness. There should be no dirt in the disconnected fuel return lines or the open connections on the injectors under any circumstances.

Protect open fuel connections from dirt entrainment using suitable methods under all circumstances.

Used injectors may only be re-installed on the same cylinder.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/622ef64282f13e6f.webp)

- Unscrew bolts -1 and 2-, and remove engine lifting eyes -3-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/3bbebe1840dcb326.webp)

- Unscrew union nuts -1 and 4- and remove high-pressure line -2-.

## 3.7.3 Installing high-pressure lines

> **Caution**
>
> To position injection lines more easily and stress-free, loosen high pressure accumulator (rail) and injectors and shift slightly. The lines must never be bent or tensioned. Tension would otherwise cause the respective line to break in the long-term.

> **Note**
>
> - Do not use tools to align the fuel rail element (fuel rail) / the injectors.
> - Observe cylinder-specific markings if reusing high-pressure lines.
> - The high-pressure lines may be re-used after the following checks:
> - Check taper seat of respective high-pressure line for deformation and cracks.
> - The inside of the line must be free of deformations, constrictions and damage.
> - Corroded lines should no longer be used.

> **Caution**
>
> When installing a new short engine, it is compulsory to fix and tighten the clamping jaws of the injectors with the specified torque after installing the high-pressure lines [⇒ 1.2 Assembly overview - fuel system](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/assembly-overview-fuel-system/#t380-82). Clamping jaws are only secured »hand-tight« for setting the injectors while installing high-pressure lines. Non-observance of these notes may lead to damage to engine.

- Use a vacuum-type cleaner to remove dirt from taper seat on high-pressure accumulator.
- Clean fuel line and head of line using cold cleaning solvent and dry using compressed air.
- Moisten union nut thread with fuel.
- Fit the injection lines from high-pressure accumulator to injector by hand first, only tighten union nuts by hand.

Next install high-pressure line from high-pressure pump to highpressure accumulator.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/69908478d8ee938b.webp)

- To install high-pressure line between high-pressure pump and high-pressure accumulator, slide support sleeve -T10411- onto fuel pressure sender - G 247-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/96dcd63353a0f10f.webp)

> **Note**
>
> - The lifting eye (for engine mounting) must be movable in order to fit union nut on high-pressure pump; loosen bolts -4- to do this.
> - Support sleeve -T10411- specifies the correct distance between fuel pressure sender - G 247- and high-pressure line.

- Only tighten union nuts on high-pressure line from high-pressure pump to high-pressure accumulator by hand.

The further final assembly follows the sequence described.

**Sequence **

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/51149b57a2c9795c.webp)

- Tighten high-pressure lines on fuel rail and injector to specified torque [⇒ 1.2 Assembly overview - fuel system](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/assembly-overview-fuel-system/#t380-82).
- To tighten injector lines, use torque wrench - V.A.G 1331- with ratchet - V.A.G 1331/1- and 17 mm socket - T40055-.
- Tighten high pressure line -2- between high pressure pump and high pressure accumulator first at high pressure pump -4- and then at high pressure accumulator -1-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/3bbebe1840dcb326.webp)

- Tighten bolt -3- for retainer for high-pressure line.

- Specified torques: [⇒ 1.2 Assembly overview - fuel system](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/assembly-overview-fuel-system/#t380-82)
- Firmly screw lifting eye in [⇒ 1.5 Removing and installing bracket for ancillaries](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-and-installing-bracket-for-ancillaries/#t96-309).

- Remove the support sleeve - T10411 -.
- Tighten fuel rail to specified torque [⇒ 1.2 Assembly overview - fuel system](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/assembly-overview-fuel-system/#t380-82).
- Tighten bolts for clamping pieces to final specified torque [⇒ 1.2 Assembly overview - fuel system](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/assembly-overview-fuel-system/#t380-82).
- Reconnect connector to fuel pressure sender - G 247-.
- Press return line connections carefully onto injectors (check seal for damage before connecting return line). You should hear them click into place.
- Engage pressure retention valve in retainer provided on the cylinder head cover.

> **Note**
>
> - After renewing the injectors “perform adaption of the correction values” ⇒ Vehicle diagnostic tester.
> - “Reading / adapting injector correction values”.
> - Never allow the high-pressure pump to run dry under any circumstances. If the low-pressure section of the fuel system was also opened (between fuel tank and high pressure pump), the fuel system must be filled [⇒ 1.3 Filling/bleeding fuel system](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/filling-bleeding-fuel-system/#t392-82).

- Start and run the engine at idling speed for several minutes and then switch off.
- Switch off ignition.
- Check the complete fuel system and return line connections for leaks.

Renew the affected component if leakage still occurs after tightening to the correct torque.

- Then test drive the vehicle, accelerating to full throttle at least once.
- Then check high-pressure part of fuel system again for leakage.

> **Note**
>
> If there is still air in the fuel system, the engine can change to emergency running mode during road test. Switch off the engine and erase event memory ⇒ Vehicle diagnostic tester. Then continue road test.
