# 5.3 Removing and installing fuel pressure sender G 247 – 1.6 TDI CR engine (EA189)

> VW Polo 6R (Senders and sensors), step by step: removing and installing fuel pressure sender G247, 1.6 TDI – 13 steps.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-fuel-pressure-sender-g-247/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 23 – Mixture preparation - injection, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [5.2 Checking fuel pressure regulating valve N276](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/checking-fuel-pressure-regulating-valve-n276/index.md)
- Next procedure: [5.4 Checking fuel pressure sender G 247](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/checking-fuel-pressure-sender-g-247/index.md)

The fuel pressure sender - G 247- is located in the fuel rail, measures the current fuel pressure in the high-pressure system and transmits a voltage signal to the diesel direct injection system control unit - J248-.

If the sender fails, the pressure is regulated by the engine control unit using a map. In back-up function, the maximum engine speed is limited to approx. 3,000 rpm.

**Removing**

> **Caution**
>
> Always read rules for cleanliness and instructions for working on fuel system [⇒ 3.1 Rules for cleanliness](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/00-technical-data/rules-for-cleanliness/#t12-146).

Follow these instructions before starting work and while working on the fuel system.

- Remove engine cover panel [⇒ 3 Engine cover panel](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/).
- Before removal, clean area around thread for fuel pressure sender, using e.g. a cold cleaning solvent. No dirt must enter the bore in the fuel rail.

> **Note**
>
> Do not allow any cleaning agent to get into the connector, clean it carefully.

- Dry fuel pressure sender - G 247-.
- Pull electrical connector off fuel pressure sender - G 247-.
- Unscrew fuel pressure sender - G 247-.
- Use suction device to extract dirt from high-pressure accumulator bore (threads and sealing surface). Do not use tools or other instruments for this purpose.

> **Note**
>
> Seal off fuel rail hole immediately with a suitable plug to prevent dirt from entering.

**Installing**

> **Note**
>
> - Check that sealing surfaces (deformable sealing lip) and threads on fuel pressure sender - G 247- are undamaged.
> - Also check sealing surface at fuel rail bore.
> - The thread on the fuel pressure sender - G 247- has a special lubricating coating. The thread must be kept free of oil and grease.

- Screw in fuel pressure sender - G 247- by hand.
- Tighten sender. Specified torque [⇒ Item 13 (1.2.1 Assembly overview - fuel system, Polo)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/assembly-overview-fuel-system/#t382-464).
- After installation, run engine at moderate speed for several minutes and then switch off.
- Check fuel system for leaks.
- Read event memory.
- Then test drive the vehicle with at least one full acceleration. Check high pressure part of fuel system again for leaks.

- Read event memory.
