# 9.1 Removing and installing engine control unit – 1.6 TDI CR engine (EA189)

> VW Polo 6R, step by step: removing and installing engine control unit, 1.6 TDI – 28 steps and 6 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-engine-control-unit/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 23 – Mixture preparation - injection, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [8.3 Removing and installing throttle valve module J338](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-throttle-valve-module-j338/index.md)
- Next procedure: [1.1 Assembly overview – silencers](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/26-exhaust-system/assembly-overview-silencers/index.md)

[⇒ 9.1.5 Removing and installing engine control unit J623, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-engine-control-unit/#t466-531)

[⇒ 9.1.6 Removing and installing engine control unit J623 with protective housing, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-engine-control-unit/#t467-255)

## 9.1.5 Removing and installing engine control unit - J623-, Polo

If you wish to renew the engine control unit, connect the vehicle diagnostic tester and perform the guided function “Renewing control unit”.

- Switch off ignition.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/2b5ad51d1c6222f8.webp)

**Removing**

- Switch off ignition.
- Release connectors on engine control unit and pull off connector.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/e4c4f7c7bf80cd42.webp)

- Press clips -arrows A- outwards and pull engine control unit out to side -B-.

**Installing**

- Insert new engine control unit and press to the left.
- Fit connectors and lock in position.
- Read event memory, rectify any faults and then clear event memory ⇒ Vehicle diagnostic tester “Guided fault finding”.
- The readiness code must be generated if the event memory has been cleared.
- Perform road test.
- Read control unit event memory again.

## 9.1.6 Removing and installing engine control unit - J623- with protective housing, Polo

If you wish to renew the engine control unit, connect the vehicle diagnostic tester and perform the guided function “Renewing control unit”.

- Switch off ignition.

**Removing**

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/c7ba2ed6120731b2.webp)

- Open wiring guide -1- and lift locking device -2-.
- Take engine control unit out of retainer.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/2029b057c65388b8.webp)

- Unscrew shear-head bolt -1- using pliers.
- Turn engine control unit -2- over and also unscrew all other shear-head bolts using pliers.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/fe3bd2980df670b5.webp)

- Pull retainer -1- and protective housing -2- off engine control unit -3- in -direction of arrow-.
- Release connectors on engine control unit and pull off connector.

**Installing**

- Fit connectors and lock in position.
- Push the protective housing over the engine control unit.
- Install retainer for protective housing using new shear-head bolts.
- Tighten shear-head bolts evenly until heads shear off.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/c7ba2ed6120731b2.webp)

- Insert engine control unit into mounting bracket on bulkhead until it audibly engages in catches -1-.
- Insert wiring into wiring guide -1- and close guide.
- If engine control unit has been renewed, clear learnt values and adapt engine control unit Vehicle diagnostic tester “Guided function”.
- Read event memory, rectify any faults and then clear Vehicle diagnostic tester event memory “Guided Fault Finding”.
- The readiness code must be generated if the event memory has been cleared.
- Perform road test.
- Read control unit event memory again.
