# 6 Lambda probe – 1.6 TDI CR engine (EA189)

> Lambda probe, 1.6 TDI on the VW Polo 6R: 3 steps, special tool 3337, tightening torques and 3 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/lambda-probe/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 23 – Mixture preparation - injection, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [5.6 Removing and installing pressure differential sender G505](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-installing-pressure-differential-sender-g505/index.md)
- Next procedure: [7.1 Assembly overview – air filter housing](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/assembly-overview-air-filter-housing/index.md)

## 6.1 Assembly overview - Lambda probe

[⇒ 6.1.3 Assembly overview - lambda probe, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/lambda-probe/#t441-309)

## 6.1.3 Assembly overview - lambda probe, Polo

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/6e150ff07606135b.webp)

- **1** Exhaust gas temperature sender 4 - G648-
  - Removing and installing
- **2** Exhaust gas temperature sender 1 - G235-
  - Removing and installing
- **3** Exhaust gas temperature sender 3 - G495-
  - Removing and installing
- **4** Pressure differential sender - G505-
  - Removing and installing [⇒ 5.6 Removing and installing pressure differential sender - G505-](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-installing-pressure-differential-sender-g505/#t432-82)
  - 45 Nm
- **5** Lambda probe - G39- with Lambda probe heater - Z19-
  - Removing and installing
  - New Lambda probes are coated with an assembly paste
  - In the case of a used lambda probe, grease only the thread with high-temperature paste ⇒ Electronic Parts
    Catalogue (ETKA).
  - Assembly paste or hightemperature paste must not get into the slots in the Lambda probe
  - 55 Nm 

## 6.2 Removing and installing Lambda probe

[⇒ 6.2.2 Removing and installing lambda probe 1 before catalytic converter GX10, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/lambda-probe/#t443-352)

## 6.2.2 Removing and installing lambda probe 1 before catalytic converter - GX10-, Polo

Special tools and workshop equipment required

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/b4fc0f5edeeef5f4.webp)

- Lambda probe open ring spanner set - 3337-

**Removing**

- Pull off engine cover panel [⇒ 3 Engine cover panel](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/).

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/d145eaea863497a0.webp)

- Detach electrical connector -4- of Lambda probe - G39-.
- Unscrew Lambda probe - G39- -2- using tool from Lambda probe open ring spanner set - 3337-.

**Installing**

Install in reverse order of removal, observing the following.

> **Note**
>
> - New Lambda probes are coated with an assembly paste; the paste must not get into the slots in the Lambda probe.
> - In the case of a used Lambda probe, grease only the thread with high-temperature paste. This paste must not get into the slots on the Lambda probe body. For high-temperature paste refer to ⇒ Parts catalogue.
> - When installing, the Lambda probe's electrical wiring connection must always be re-attached in the same locations to prevent the Lambda probe cable from coming into contact with the exhaust pipe.
> - Specified torque [⇒ 6.1.3 Assembly overview - lambda probe, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/lambda-probe/#t441-309) 

## Tightening torques on this page

### 6.1.3 Assembly overview - lambda probe, Polo [To the drawing](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/lambda-probe/#6-1-3-assembly-overview-lambda-probe-polo)
| Item | Part | Torque | Notes |
| --- | --- | --- | --- |
| 4 | Pressure differential sender - G505- | 45 Nm |  |
| 5 | Lambda probe - G39- with Lambda probe heater - Z19- | 55 Nm | Removing and installing · New Lambda probes are coated with an assembly paste · Assembly paste or hightemperature paste must not get into the slots in the Lambda probe · Catalogue (ETKA). |
