# 1.2 Assembly overview – fuel system – 1.6 TDI CR engine (EA189)

> Fuel system – assembly overview, 1.6 TDI (Injection system) on the VW Polo 6R: 3 steps, tightening torques and 3 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/assembly-overview-fuel-system/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 23 – Mixture preparation - injection, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [1.1 Schematic overview – fuel system](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/schematic-overview-fuel-system/index.md)
- Next procedure: [1.3 Filling/bleeding fuel system](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/filling-bleeding-fuel-system/index.md)

[⇒ 1.2.1 Assembly overview - fuel system, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/assembly-overview-fuel-system/#t380-158)

## 1.2.1 Assembly overview - fuel system, Polo

[⇒ 2 Safety information](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/00-technical-data/)

[⇒ 3.1 Rules for cleanliness](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/00-technical-data/rules-for-cleanliness/#t12-146)

> **Caution**
>
> To prevent the high-pressure fuel pump from running while it is empty and to ensure that the engine starts quickly after parts have been renewed, it is important to observe the following:
>
> - If fuel system components between fuel tank and fuel high-pressure pump are removed or renewed;
> - Basic setting “Checking fuel pre-supply pump” must be carried out to bleed fuel system.
> - If a fuel pump, fuel line (between fuel tank and fuel highpressure pump) or fuel filter is removed or renewed
> - Basic setting “Testing fuel pre-supply pump” must be carried out »once« before first starting engine.
> - If the high-pressure fuel pump is removed or renewed, the basic setting “Checking fuel system pressurisation pump” must be performed »three times« before the engine is started for the first time.
> - Performing first fuel filling after installing high-pressure pump [⇒ 4.2 Removing and installing high-pressure pump](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-high-pressure-pump/#t420-288).

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/54e6783cc53fa271.webp)

- **1** Fuel return line

> **Caution**
>
> Gradual introduction of a new fuel return line. Always observe notes [⇒ 1.2.1 Assembly overview - fuel system, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/assembly-overview-fuel-system/#t383-512) !
>
> - Flexible
> - The following component must be renewed any time the fuel return line is removed and installed: “return line retaining clip”
> - To fuel tank
> - The fuel return line must be free of kinks, damage and blockages.
> - Do not dismantle the fuel return lines.
> - Only renew O-ring if necessary
> - The pressure retention valve maintains a residual pressure in the return lines.
> - This residual pressure is required for the control function of the injectors.
> - Check pressure retention valve [⇒ 3.4 Check pressure retention valve in fuel return line](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/check-pressure-retention-valve-in-fuel-return-line/#t401-545).

- **2** Fuel pressure regulating valve - N 276-
  - Cannot be re-installed.
  - Checking [⇒ 5.2 Checking fuel pressure regulating valve - N276-](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/checking-fuel-pressure-regulating-valve-n276/#t428-576)
  - Removing and installing [⇒ 5.1 Removing and installing fuel pressure regulating valve - N 276-](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-installing-fuel-pressure-regulating-valve-n276/#t426-254)
  - 80 Nm
- **3** Fuel return line
  - Rigid.
- **4** Bolt
  - 10 Nm
- **5** High-pressure pump
  - Removing and installing [⇒ 4.2 Removing and installing high-pressure pump](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-high-pressure-pump/#t420-288)
  - With fuel metering valve - N290- (do not open)
  - After renewing, a first fuel filling must be performed (never allow the pump to run while it is still empty) [⇒ 1.3 Filling/bleeding fuel system](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/filling-bleeding-fuel-system/#t392-82).
- **6** Bolt
  - 20 Nm + turn 180° further
  - Renew
- **7** Hub
  - With sender ring
  - Use counterhold - T10051- to loosen and tighten.
  - To remove, use puller - T40064-.

- **8** Nut
  - 95 Nm
- **9** Toothed belt pulley on high-pressure pump
  - Bolts 20 Nm
  - Renew
- **10** Bolt
  - 20 Nm + turn 45° further
  - Renew
- **11** Bolt
  - 10 Nm 
- **12** High-pressure line
  - 28 Nm
  - Between high-pressure pump and fuel rail
  - Install so that component is not under tension

> **Note**
>
> - The high-pressure line may be re-used after the following checks:
> - Check taper seat of high-pressure line for deformation and cracks.
> - The inside of the line must be free of deformations, constrictions and damage.
> - Corroded lines should no longer be used. 

- **13** Fuel pressure sender - G 247-
  - Removing and installing [⇒ 5.3 Removing and installing fuel pressure sender - G 247-](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-fuel-pressure-sender-g-247/#t429-702)
  - 100 Nm
- **14** High-pressure accumulator
  - Removing and installing [⇒ 3.6 Removing and installing fuel rail](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-fuel-rail/#t408-590)
- **15** Bolt
  - 22 Nm
- **16** High-pressure lines
  - Removing and installing [⇒ 3.7 Removing and installing high-pressure lines](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-high-pressure-lines/#t412-380)
  - 28 Nm
  - Between fuel rail and injectors
  - Do not interchange
  - Install so that component is not under tension

> **Note**
>
> - Observe cylinder-specific markings if reusing high-pressure lines.
> - The high-pressure lines may be re-used after the following checks: 
> - Check taper seat of respective high-pressure line for deformation and cracks.
> - The inside of the line must be free of deformations, constrictions and damage.
> - Corroded lines should no longer be used.

- **17** Seal
  - Renew if damaged [⇒ 1.4.1 Removing and installing injector seal in cylinder head cover](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-cylinder-head-cover/#t180-231).
- **18** Seal
  - Renew if damaged [⇒ 1.4.1 Removing and installing injector seal in cylinder head cover](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-cylinder-head-cover/#t180-231).
- **19** Injectors
  - Removing and installing [⇒ 3.5 Removing and installing injectors](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-injectors/#t403-309)
  - The following components and seals/O-rings must be renewed each time on removal/installation: “bolt for clamping piece”, “copper seal”, “O-ring of injector bore” and “retaining clip for return connection”.
  - Before re-using “high-pressure line”, perform visual check of taper seats for damage such as transverse scores or corrosion; always renew if damaged.
  - If they are to be re-installed, injectors, high-pressure fuel lines and clamping pieces must always be refitted in their original positions (i.e. on the same cylinder). 
- **20** Bolt for clamp
  - Renew

Tighten securing bolts to a maximum of 1 to 2 Nm at first.

After the high-pressure lines have been fitted. Final specified torque: 8 Nm + turn 270° further.

- **21** O-ring for fuel return lines
  - The following component must be renewed any time the fuel return line is removed and installed: “return line retaining clip”
  - Only renew O-ring if necessary
  - Observe notes on installing [⇒ 1.2.1 Assembly overview - fuel system, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/assembly-overview-fuel-system/#t383-512). 

Removing O-ring for fuel return lines.

Proceed with extreme caution. Avoid damage to fuel return line.

- Lever old O-ring very carefully off fuel return line.

Do not work with a sharp-edged tool. Preferably use a plastic tool.

Installing O-ring for fuel return lines

> **Caution**
>
> Gradual introduction of a new fuel return line. Always ensure proper allocation of components when renewing the O-rings. The new fuel return line can be identified by the indentation -arrow- in the connecting piece. The new fuel return lines must always be equipped with the orange O-rings ⇒ Electronic Parts Catalogue (ETKA). Do not use other O-rings, because this will cause leaks and failures.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/5f7736d898f0f175.webp)

A - Connection for »new« fuel return line, with indentation -arrow-, use orange O-ring.

B - Connection for »old« fuel return line, without indentation, use green O-ring.

> **Note**
>
> Prevent O-rings from rolling when sliding them on. The O-rings must be free of twists in their seats in fuel return line.

Proceed with extreme caution. Avoid damage to the O-ring and fuel return line.

- Clean seating surfaces for O-rings on fuel return line very carefully.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/a54bad9c78d0d184.webp)

- Carefully push O-ring -1- on its seat -2-.

## Tightening torques on this page

### 1.2.1 Assembly overview - fuel system, Polo [To the drawing](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/assembly-overview-fuel-system/#1-2-1-assembly-overview-fuel-system-polo-golf-golf-plus-golf)
| Item | Part | Torque | Notes |
| --- | --- | --- | --- |
| 2 | Fuel pressure regulating valve - N 276- | 80 Nm | Cannot be re-installed. |
| 4 | Bolt | 10 Nm |  |
| 6 | Bolt | 20 Nm +180° | Renew |
| 8 | Nut | 95 Nm |  |
| 9 | Toothed belt pulley on high-pressure pump | 20 Nm | Bolts · Renew |
| 10 | Bolt | 20 Nm +45° | Renew |
| 11 | Bolt | 10 Nm |  |
| 12 | High-pressure line | 28 Nm | Between high-pressure pump and fuel rail · Install so that component is not under tension |
| 13 | Fuel pressure sender - G 247- | 100 Nm |  |
| 15 | Bolt | 22 Nm |  |
| 16 | High-pressure lines | 28 Nm | Between fuel rail and injectors · Do not interchange · Install so that component is not under tension |

### 1.2.1 Assembly overview - fuel system, Polo [To the steps](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/assembly-overview-fuel-system/#1-2-1-assembly-overview-fuel-system-polo-golf-golf-plus-golf)
| Step | Torque |
| --- | --- |
| Tighten securing bolts to a maximum of 1 to 2 Nm at first. | 2 Nm |
| After the high-pressure lines have been fitted. Final specified torque: 8 Nm + turn 270° further. | 8 Nm |
