# 1.2 Removing and installing turbocharger – 1.6 TDI CR engine (EA189)

> Removing and installing turbocharger, 1.6 TDI on the VW Polo 6R: 25 steps, special tools T10395, T10403 and V.A.G 1782 and 18 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/21-turbocharging-supercharging/removing-and-installing-turbocharger/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 21 – Turbocharging/supercharging, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [1.1 Assembly overview – turbocharger](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/21-turbocharging-supercharging/assembly-overview-turbocharger/index.md)
- Next procedure: [1.3 Renewing vacuum unit for turbocharger](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/21-turbocharging-supercharging/renewing-vacuum-unit-for-turbocharger/index.md)

[⇒ 1.2.4 Removing and installing turbocharger, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/21-turbocharging-supercharging/removing-and-installing-turbocharger/#t347-715)

> **Caution**
>
> If a mechanical fault is discovered on the turbocharger (e.g. a destroyed compressor impeller), it is not sufficient to just renew the turbocharger. To avoid any subsequent damage, the following work must be carried out:
>
> - Check air filter housing, air filter element and air inlet hoses for contamination.
> - Check the whole charge air path and charge air cooler for foreign objects.
> - If foreign objects are discovered in the charge air system, clean the charge air path and, if necessary, renew the charge air cooler.

## 1.2.4 Removing and installing turbocharger, Polo

Special tools and workshop equipment required 

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/c979c192814bec52.webp)

- Tool insert, AF 17 mm - T10395-

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/298718713694ff63.webp)

- Transport lock - T10403-

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/7201d8102b317c09.webp)

- Torque wrench - V.A.G 1331-
- Used oil collection and extraction unit, e.g. -V.A.G 1782-

> **Caution**
>
> If a mechanical fault is found on the turbocharger, e.g. a destroyed compressor impeller, just renewing the turbocharger is not enough. To prevent this from causing further damage, perform the following repairs:
>
> - Check air filter housing, air filter element and intake hoses for soiling.
> - Check complete charged air routing and charge air cooler for foreign objects.

If foreign objects are found in the charge air system, the charged air routing must be cleaned and the charge air cooler must be renewed, if necessary.

[⇒ 2 Safety information](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/00-technical-data/)

[⇒ 3.1 Rules for cleanliness](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/00-technical-data/rules-for-cleanliness/#t12-146)

**Removing**

- With ignition switched off, disconnect battery earth strap. ⇒ Electrical system; Rep. gr. 27; Battery; Disconnecting and connecting battery
- Remove engine cover panel [⇒ 3 Engine cover panel](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/).

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/617810f72cc3401a.webp)

- Pull connector -1- off position sender for charge pressure positioner - G581- on turbocharger.
- Remove air filter housing with air mass meter and intake hose [⇒ 7.2.2 Removing and installing air filter housing, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-air-filter-housing/#t448-678).
- Remove plenum chamber bulkhead ⇒ General body repairs, exterior; Rep. gr. 50; Plenum chamber bulkhead; Assembly overview - bulkhead.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/e5500415c314cb2b.webp)

- Loosen particulate filter. To do this, unscrew bolt -1-.
- Loosen bolt -2- and remove clamp.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/82b78528ff3849ce.webp)

- Disconnect connector -3-.
- Unscrew bolt -2-, remove pressure differential sender - G 505-, free hoses -1-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/2d3503be34986865.webp)

- On flexible joint in front exhaust pipe, fasten the transport lock - T10403- -arrow-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/35449eb632b13f9e.webp)

- Unscrew bolts -1- and nuts -2-, remove bracket for particulate filter.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/c4c8529a93d3f271.webp)

- Pull particulate filter from mountings -arrows-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/fc858f42dba1be11.webp)

- Loosen securing bolts -arrows- of clamping sleeve, then push down backwards from front exhaust pipe.
- Move particulate filter to side and fix using suitable means.

Right-hand drive vehicles [⇒ 2.1.4 Assembly overview - front exhaust pipe with particulate filter, Polo, right-hand drive](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/26-exhaust-system/assembly-overview-emission-control/#t488-231)

**Continued for all vehicles**

- Remove oil supply line together with oil return line (turbocharger support) [⇒ 4.2 Removing and installing oil supply line](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/17-lubrication/removing-and-installing-oil-supply-line/#t254-82).
- Pull vacuum line -3- off turbocharger.
- Remove pulsation damper with connecting hose to charge air pipe.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/784149f150cfbcce.webp)

- Unscrew bolts -arrows-.
- Take off pulsation damper -2-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/2f01703e44b309b5.webp)

- Unscrew bolts and remove pipes -A- for exhaust gas recirculation.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/771a4aadba0969bf.webp)

- Unscrew bolts -arrows- and remove heat shield.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/fbba884c79d7add9.webp)

Remove bolts -arrows- from exhaust gas recirculation cooler in order to pull exhaust manifold from studs.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/7ee4e0eabfed225a.webp)

- Unscrew nuts -arrows- and pull turbocharger with exhaust manifold off cylinder head.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/c4222d02a4556264.webp)

- Carefully remove turbocharger from above in direction of gearbox.

**Installing**

> **Caution**
>
> Before installing, check whether flexible joint of oil return line is bent and thus stretched. If this is the case, micro-fractures may have been caused and this will cause leaks. If necessary, renew oil return line before installing turbocharger.

- Install in reverse order. During this procedure, observe the following:

- Note installation position of exhaust temperature sender 1 - G 235-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/bce3993d5bdf426f.webp)

Installation position of exhaust gas temperature sender with angled cable guide

> **Note**
>
> When installing the exhaust temperature sender with angled cable guide, adhere to dimension -a- of 3 … 5 mm from the turbocharger support threaded connection.

Specified torques:

- [⇒ 1.1.2 Assembly overview - turbocharger, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/21-turbocharging-supercharging/assembly-overview-turbocharger/#t327-528).
- [⇒ 4.1.2 Assembly overview - oil supply line, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/17-lubrication/assembly-overview-oil-circuit/#t253-82).
- [⇒ 4.1 Assembly overview - exhaust gas recirculation](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/26-exhaust-system/assembly-overview-exhaust-gas-recirculation/#t530-237).

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/bb2e59b000011d7b.webp)

- Observe sequence when installing particulate filter:

| 1) | Position particulate filter on turbo charger and loosely attach clip -1- |
| --- | --- |
| 2) | Screw in nuts -2, 4- and bolts -3, 5- loosely by hand • It must still be possible to move particulate filter and bracket |
| 3) | Tighten clip -1- |
| 4) | Tighten nuts -2, 4- |
| 5) | Tighten bolts -3, 5- |
