# 2.3 Removing and installing thermostat – 1.6 TDI CR engine (EA189)

> Removing and installing thermostat, 1.6 TDI on the VW Polo 6R: 15 steps, special tools 3185, T10007 and T10058 and 6 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/removing-and-installing-thermostat/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 19 – Cooling, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [2.2 Removing and installing coolant pump](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/removing-and-installing-coolant-pump/index.md)
- Next procedure: [2.4 Checking thermostat](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/checking-thermostat/index.md)

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/5cde635a0b0f7420.webp)

Special tools and workshop equipment required

- 10 mm jointed spanner - 3185-
- Refractometer - T10007-
- Multi-point bit - T10058-
- Torque wrench - V.A.G 1331/-
- Drip tray for workshop hoist - VAS 6208-
- Hose clamp pliers - VAS 6340-

**Removing**

> **Note**
>
> Renew gaskets and seals.

- Drain coolant [⇒ 1.3 Draining and adding coolant](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/draining-and-adding-coolant/#t267-554).

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/560544959c07a537.webp)

- Unscrew bolts -arrows-.
- Free off coolant hose -3-.
- Disconnect electrical connection -1- on charge pressure sender - G31- / intake air temperature sensor - G42- and remove right charge air pipe.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/71eadeda7c26c4a8.webp)

- Disconnect coolant hose from union, loosen hose clip -1- for this.
- Loosen union securing bolts -arrows- using T-bar and 10 mm socket - 3185- and unscrew with 5 mm Allen key extension - T10058- and remove union with thermostat -1-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/f0aab602b974ac23.webp)

- Turn thermostat -2- approx. 15° clockwise -arrow- and remove from union.
- Remove O-ring -1-.

**Installing**

- Specified torque [⇒ 2.1.1 Assembly overview - coolant pump, thermostat](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/assembly-overview-coolant-pump-thermostat/#t272-368).

Install in reverse order of removal, observing the following.

> **Note**
>
> - Renew O-ring.
> - Hose unions and air intake pipes and hoses must be free of oil and grease before installation.
> - Secure all hose connections with the correct type of hose clips (same as original equipment) ⇒ Electronic parts catalogue (ETKA).

- Clean and smoothen sealing surface for O-ring.
- Moisten O-ring with coolant.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/7aaa23a9cfe0359a.webp)

- Insert thermostat -3- with O-ring -2- in guides on union -1-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/877fe1450141a74f.webp)

- Turn thermostat -1- anticlockwise -arrow- to stop.
- Install charge air pipe.
- Polo: Install connecting hoses with screw-type clips [⇒ 2.1.3 Assembly overview - charge air system, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/21-turbocharging-supercharging/assembly-overview-charge-air-system/#t364-82).
- Add coolant [⇒ 1.3.2 Filling with coolant](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/draining-and-adding-coolant/#t270-82).
