# 2.7 Removing and installing coolant temperature sender – 1.6 TDI CR engine (EA189)

> VW Polo 6R, step by step: removing and installing coolant temperature sender, 1.6 TDI – 21 steps and 8 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/removing-and-installing-coolant-temperature-sender/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 19 – Cooling, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [2.6 Electric coolant pump](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/electric-coolant-pump/index.md)
- Next procedure: [3.1 Assembly overview – coolant pipes](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/assembly-overview-coolant-pipes/index.md)

[⇒ 2.7.1 Removing and installing coolant temperature sender G62 ](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/removing-and-installing-coolant-temperature-sender/#t289-711)

[⇒ 2.7.3 Removing and installing radiator outlet coolant temperature sender G83, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/removing-and-installing-coolant-temperature-sender/#t293-82)

## 2.7.1 Removing and installing coolant temperature sender - G62-

Special tools and workshop equipment required 

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/d1518fb6b79b7cf8.webp)

- Release lever - 80 - 200-

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/b771331ae451a1ac.webp)

**Removing**

- Engine cold.

- Briefly open filler cap for coolant expansion tank in order to reduce pressure in cooling system.
- Remove engine cover panel [⇒ 3 Engine cover panel](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/).
- Remove air filter housing [⇒ 7.2 Removing and installing air filter housing](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-air-filter-housing/#t447-146).
- Remove noise insulation:
  Polo ⇒ General body repairs, exterior; Rep. gr. 50; Noise insulation; Assembly overview - noise insulation

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/4227661b317b94ae.webp)

- Pull off crankcase breather hose -1- from cylinder head cover by pressing the release buttons.
- Release connector on hose -1- for crankcase bleeding and pull off.
- Free vacuum hoses -arrows- at air pipe.
- Unscrew bolt -2-, swing air pipe with inlet pipe to rear and remove from turbocharger.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/d25ccd410d035f3d.webp)

Vehicles with dual clutch gearbox

- Pull off coolant hoses from gearbox oil cooler by undoing hose clips -arrows-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/9d36dc9ccdf3bf8c.webp)

**Continued for all vehicles**

- Remove bolt -arrows-.
- Free electrical wiring and hoses on left air pipe using removal lever - 80 - 200-.
- Loosen hose clip -3- and press left air pipe with coolant pipe aside.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/8fd4456983865095.webp)

- Unlock and pull connector -4- off coolant temperature sender - G62-.

> **Note**
>
> - Place a cloth under connecting piece to absorb escaping coolant.
> - Insert new coolant temperature sender - G62- immediately into union to avoid loss of coolant.

- Pull off retaining clip -3- and pull coolant temperature sender - G62- out of screw connection.

**Installing**

Install in reverse order. During this procedure, observe the following:

> **Note**
>
> - Renew O-ring.
> - Insert new coolant temperature sender - G62- immediately into union to avoid loss of coolant.

- Check coolant level.

## 2.7.3 Removing and installing radiator outlet coolant temperature sender - G83-, Polo

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/9d7ac900ff9eb8a9.webp)

**Removing**

- Engine cold.

- Briefly open filler cap -1- for coolant expansion tank in order to reduce pressure in cooling system.

> **Note**
>
> Disregard -item 2-.

- Remove noise insulation:
  Polo ⇒ General body repairs, exterior; Rep. gr. 50; Noise insulation; Assembly overview - noise insulation

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/38fee64904fe529b.webp)

- Disconnect connector -2-.

> **Note**
>
> Place a cloth underneath to catch escaping coolant.

- Pull off retaining clip -1- and pull coolant temperature sender at radiator outlet - G83- -item 3- out of connection of coolant pipe.

**Installing**

Install in reverse order of removal, observing the following.

> **Note**
>
> - Renew O-ring.
> - Insert new radiator outlet coolant temperature sender - G83- immediately into coolant pipe to avoid loss of coolant.

- Install noise insulation:
  Polo ⇒ General body repairs, exterior; Rep. gr. 50; Noise insulation; Assembly overview - noise insulation
- Check coolant level.
