# 3.2 Removing and installing coolant pipes – 1.6 TDI CR engine (EA189)

> Removing and installing coolant pipes, 1.6 TDI on the VW Polo 6R: 35 steps, special tools VAS 6362, 3094 and VAS 6208 and 14 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/removing-and-installing-coolant-pipes/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 19 – Cooling, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [3.1 Assembly overview – coolant pipes](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/assembly-overview-coolant-pipes/index.md)
- Next procedure: [4.1 Assembly overview – radiator/radiator fan](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/assembly-overview-radiator-radiator-fan/index.md)

[⇒ 3.2.1 Removing and installing front coolant pipe, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/removing-and-installing-coolant-pipes/#t296-552)

[⇒ 3.2.4 Removing and installing right coolant pipes, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/removing-and-installing-coolant-pipes/#t306-543)

## 3.2.1 Removing and installing front coolant pipe, Polo

Special tools and workshop equipment required

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/acec0bc59abe83b3.webp)

- Release lever - 80 - 200- 

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/12d5ed9bede66924.webp)

- Spring-type clip pliers - VAS 6362-

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/2377e318581f9deb.webp)

**Removing**

- Drain coolant [⇒ 1.3 Draining and adding coolant](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/draining-and-adding-coolant/#t267-554).
- Remove air filter housing [⇒ 7.2.2 Removing and installing air filter housing, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-air-filter-housing/#t448-678).
- Remove oil filter bracket with engine oil cooler [⇒ 3.2 Removing and installing oil filter housing](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/17-lubrication/removing-and-installing-oil-filter-housing/#t244-663)

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/8ef3b8d0ab4d2cd9.webp)

- Country-specific version for cold countries: Disconnect electrical connector -2-.
- Press release buttons and remove hose -1- for venting crankcase.
- Pull off vacuum hose -arrow-.
- Unscrew bolt -3-, swing air pipe with inlet connection to rear and pull off from turbocharger.

> **Note**
>
> Disregard -item 4-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/563febb4ec134a45.webp)

- Unclip wiring harness from retainer -arrow-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/5407a9436bb65f51.webp)

- Free wiring harnesses -arrows- and electrical connector -1- at bracket.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/c0b7ad02ba487259.webp)

- Remove air intake hose. To do this, loosen hose clips -1, 2-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/9dfc4648512aac6b.webp)

- Unscrew bolts -arrows-.
- Free electrical wiring and hoses on left air pipe using removal lever - 80 - 200-.
- Loosen hose clip -1- and remove left air pipe.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/52dc65915306a732.webp)

- Disconnect coolant hoses and free them, loosening hose clips -1- to do so.

> **Note**
>
> - Items 2, 3, 4- can be disregarded.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/99b9fc0d988ddcd0.webp)

- Remove electrical connector -2- for Hall sender - G40- from retainer and separate.
- Remove bracket from front coolant pipe.
- Remove coolant hoses after loosening hose clips -1- and -3-.
- Undo bolts -arrows- and pull front coolant pipe off cylinder block towards the left.

**Installing**

Install in reverse order of removal, observing the following.

- Specified torques [⇒ 3.1.2 Assembly overview - coolant pipes, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/assembly-overview-coolant-pipes/#t295-234)

> **Note**
>
> - Renew gaskets, seals and O-rings.
> - Secure all hose connections with the correct type of hose clips (same as original equipment) ⇒ Electronic parts catalogue (ETKA).

- Clean or smoothen sealing surface for O-ring.
- Moisten O-ring with coolant and slide onto front coolant pipe.
- Push front coolant pipe into cylinder block.
- Installing intake hoses with screw-type clips [⇒ 2.3 Assembly overview - charge-air hose connections](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/21-turbocharging-supercharging/assembly-overview-charge-air-hose-connections/#t369-82).
- Install charge air pipe [⇒ 2.1.3 Assembly overview - charge air system, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/21-turbocharging-supercharging/assembly-overview-charge-air-system/#t364-82).
- Install air pipe with inlet connection.
- Install oil filter bracket with engine oil cooler [⇒ 3.2 Removing and installing oil filter housing](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/17-lubrication/removing-and-installing-oil-filter-housing/#t244-663).
- Install air filter housing [⇒ 7.2.2 Removing and installing air filter housing, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-air-filter-housing/#t448-678).
- Add coolant [⇒ 1.3.2 Filling with coolant](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/draining-and-adding-coolant/#t270-82).

## 3.2.4 Removing and installing right coolant pipes, Polo

Special tools and workshop equipment required

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/cd6609fdc34cf116.webp)

- Hose clamps to 25 mm - 3094- 

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/2a9d1847970a22bd.webp)

- Drip tray for workshop hoist - VAS 6208-

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/da48dd7964b7c4f4.webp)

- Spring-type clip pliers - VAS 6362-

**Removing**

- Remove noise insulation:
  Polo ⇒ General body repairs, exterior; Rep. gr. 50; Noise insulation; Assembly overview - noise insulation

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/3b4adc99189d34fe.webp)

- Disconnect electrical connector -2- and free off electrical wiring.
- Place drip tray - VAS 6208- beneath engine.
- Clamp off coolant hoses with hose clamps -3094- and remove from right coolant pipes, releasing hose clips -1, 3- to do so.
- Undo bolts -arrows- and remove coolant pipes on right.

**Installing**

Install in reverse order of removal, observing the following.

- Specified torque [⇒ 3.1.2 Assembly overview - coolant pipes, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/assembly-overview-coolant-pipes/#t295-234).

> **Note**
>
> Secure all hose connections with the correct type of hose clips (same as original equipment) ⇒ Electronic parts catalogue (ETKA).

- Install noise insulation:
  Polo ⇒ General body repairs, exterior; Rep. gr. 50; Noise insulation; Assembly overview - noise insulation
- Check coolant level [⇒ 1.3 Draining and adding coolant](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/draining-and-adding-coolant/#t267-554).
