# 2.6 Electric coolant pump – 1.6 TDI CR engine (EA189)

> Electric coolant pump, 1.6 TDI on the VW Polo 6R: 6 steps, special tools 3094 and VAS 6362 and 3 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/electric-coolant-pump/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 19 – Cooling, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [2.5 Removing and installing 4/2-way valve with thermostat](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/removing-installing-4-2-way-valve-thermostat/index.md)
- Next procedure: [2.7 Removing and installing coolant temperature sender](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/removing-and-installing-coolant-temperature-sender/index.md)

[⇒ 2.6.1 Removing and installing coolant circulation pump 2 V178, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/electric-coolant-pump/#t285-467)

## 2.6.1 Removing and installing coolant circulation pump 2 - V178-, Polo

Special tools and workshop equipment required

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/66bb308425769f70.webp)

- Hose clamps to 25 mm - 3094- 

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/12d5ed9bede66924.webp)

- Spring-type clip pliers - VAS 6362-

**Removing**

- Remove noise insulation:
  Polo ⇒ General body repairs, exterior; Rep. gr. 50; Noise insulation; Assembly overview - noise insulation

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/3da0740e5b57e726.webp)

> **Note**
>
> Place a cloth underneath coolant circulation pump 2 - V178- to absorb escaping coolant.

- Clamp off coolant hoses with hose clamps -3094- and remove: to do this, loosen hose clips -arrows-.
- Disconnect connector -2-.
- Undo bolt -3- and remove coolant circulation pump 2 - V178-.

> **Note**
>
> Disregard -item 1-.

**Installing**

Install in reverse order of removal, observing the following.

- Specified torque [⇒ 3.1.2 Assembly overview - coolant pipes, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/assembly-overview-coolant-pipes/#t295-234).

> **Note**
>
> - Hose unions and air intake pipes and hoses must be free of oil and grease before installation.
> - Secure all hose connections with the correct type of hose clips (same as original equipment) ⇒ Electronic parts catalogue (ETKA).

- Install noise insulation:
  Polo ⇒ General body repairs, exterior; Rep. gr. 50; Noise insulation; Assembly overview - noise insulation
- Check coolant level [⇒ 1.3 Draining and adding coolant](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/draining-and-adding-coolant/#t267-554).
