# 1.3 Draining and adding coolant – 1.6 TDI CR engine (EA189)

> Draining and adding coolant, 1.6 TDI (Cooling system/coolant) on the VW Polo 6R: 19 steps and 7 drawings. Danger of scalding due to steam and hot coolant.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/draining-and-adding-coolant/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 19 – Cooling, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [1.2 Checking cooling system for leaks](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/checking-cooling-system-for-leaks/index.md)
- Next procedure: [2.1 Assembly overview – coolant pump, thermostat](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/assembly-overview-coolant-pump-thermostat/index.md)

[⇒ 1.3.1 Draining coolant](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/draining-and-adding-coolant/#t267-610)

[⇒ 1.3.2 Filling with coolant](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/draining-and-adding-coolant/#t270-82)

## 1.3.1 Draining coolant

> **Warning**
>
> Danger of scalding due to steam and hot coolant.

On a warm engine, the cooling system is under high pressure.

Cover filler cap on expansion tank with a cloth and open carefully to release pressure.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/904cb99f1a32e1db.webp)

- Open filler cap -1- on coolant expansion tank.
- Remove noise insulation:
  Polo ⇒ General body repairs, exterior; Rep. gr. 50; Noise insulation; Assembly overview - noise insulation
- Place drip tray - VAS 6208- beneath engine.

**Polo **

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/00dcbd9b0f335821.webp)

- Pull off coolant hoses -2- from coolant circulation pump 2 - V178-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/645dd516537a3229.webp)

- Disconnect lower coolant hose from radiator, loosen hose clamp -arrow- to do so and then drain off coolant.
- Open clamp -arrow- for this.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/85981af4510303c6.webp)

- Disconnect lower coolant hose on right from radiator, loosen hose clamp -arrow- to do so and then drain off coolant.
- Disconnect coolant hose from oil filter housing, loosen hose clamp -arrow- to do so and then drain off remaining coolant.

**Continuation for all vehicles**

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/82d02a3507018c0f.webp)

- To drain coolant from engine, also remove coolant hose from engine oil cooler -arrow-.

> **Note**
>
> Please observe disposal instructions!

## 1.3.2 Filling with coolant

> **Caution**
>
> If large components (e.g. engine, radiator etc.) are to be removed/installed, it is absolutely necessary to drain the cooling system.

If the coolant has been drained off, the cooling system must be filled using the cooling system charge unit - VAS 6096- [⇒ 1.3.2 Filling with coolant](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/draining-and-adding-coolant/#t271-173).

> **Note**
>
> - The water used for mixing has a major influence on the effectiveness of the coolant. Because the water quality differs from country to country and even region to region, Volkswagen has decided to define the quality of the water to be used in the coolant system. Distilled water fulfils all requirements.
> - Use only coolant additives which conform with the ⇒ Electronic parts catalogue (ETKA). Other coolant additives may reduce corrosion protection substantially. The resulting damage could lead to loss of coolant and subsequent severe damage to the engine.
> - Mixed in the proper proportions, coolant inhibits frost and corrosion damage as well as scaling. Such additives also raise the boiling point of the coolant. For this reason, the cooling system must be filled all-year-round with coolant additives.
> - Because of its high boiling point, the coolant improves engine reliability under heavy loads, particularly in countries with tropical climates.
> - Frost protection must be guaranteed down to about -25 °C (in countries with Arctic climates, down to about -35 °C).
> - Do not reduce the coolant concentration by adding water even in warmer seasons and in warmer countries. The coolant additive concentration must be at least 40%.
> - If a stronger anti-freeze mixture is necessary due to harsher weather conditions, the coolant additive content can be increased. However, this is only permitted to 60% (antifreeze protection to about -40 °C). Otherwise, the antifreeze protection will be reduced again and the cooling effect will be impaired.
> - If radiator, heat exchanger, cylinder head or cylinder head gasket is renewed, do not reuse old coolant.
> - The refractometer - T10007A- is recommended for determining the current anti-freeze density.

Recommended mixture ratios:

- Coolant additive (40 %) and distilled water (60 %) for frost protection to -25 °C
- Coolant additive (50%) and distilled water (50%) for frost protection to -35°C
- Coolant additive (60 %) and distilled water (40 %) for frost protection to -40 °C

**Installing**

- Reconnect coolant hoses.

- Install noise insulation:
  Polo ⇒ General body repairs, exterior; Rep. gr. 50; Noise insulation; Assembly overview - noise insulation

With cooling system charge unit - VAS 6096- :

- Screw adapter for cooling system tester - V.A.G 1274/8- onto expansion tank.
- Fill coolant circuit using cooling system charge unit - VAS 6096-.

Operating instructions for cooling system charge unit - VAS 6096- are enclosed with unit.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/dc0e2a31b774f7e3.webp)

- Fill tank of cooling system charge unit - VAS 6096- with at least 8 litres of pre-mixed coolant in correct mixture ratio.

> **Note**
>
> Exhaust air takes a slight quantity of coolant along with it; this should be collected -2-.

Without cooling system charge unit - VAS 6096- :

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/ed2979bbbee2b62b.webp)

- Slowly fill coolant to upper marking of shaded field on expansion tank.
- Fit expansion tank cap.
- Start engine and maintain an engine speed of about 2,000 rpm for about 3 minutes.
- Then run engine at idling speed until radiator fan cuts in.
- Check coolant level and top up as needed. When engine is at normal operating temperature, the coolant level must be at the upper mark; when engine is cold, in the middle of the shaded field.
