# 1.2 Removing and installing sump – 1.6 TDI CR engine (EA189)

> Removing and installing sump, 1.6 TDI (Sump, oil pump) on the VW Polo 6R: 22 steps, special tools VAS 3185 and T10058, tightening torques and 12 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/17-lubrication/removing-and-installing-sump/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 17 – Lubrication, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [1.1 Assembly overview – sump/oil pump](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/17-lubrication/assembly-overview-sump-oil-pump/index.md)
- Next procedure: [1.3 Removing and installing oil level and oil temperature sender G 266](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/17-lubrication/removing-and-installing-oil-level-temperature-sender-g266/index.md)

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/b62abecd71ae27aa.webp)

Special tools and workshop equipment required

- 10 mm jointed spanner - VAS 3185-
- Multi-point bit - T10058-
- Torque wrench (5 … 50 Nm) - V.A.G 1331-
- Used oil collection and extraction unit - V.A.G 1782-
- Sealant as per ⇒ Electronic Parts Catalogue (ETKA)
- Hand drill with plastic brush
- Safety glasses
- Scraper 

> **Note**
>
> - Metal shavings or a large quantity of small metal particles found during engine repair could indicate that the crankshaft bearings or conrod bearings are damaged. To avoid any subsequent damage, you must carry out the following work following repair:
> - Thoroughly clean oil channels.
> - Renew engine oil cooler [⇒ 2.2 Removing and installing engine oil cooler](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/17-lubrication/removing-and-installing-engine-oil-cooler/#t238-132).
> - Renew oil filter element [⇒ 3.1 Assembly overview - oil filter housing](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/17-lubrication/assembly-overview-oil-filter-housing/#t243-200).
> - Oil capacities, oil specifications, viscosity grades [⇒ 1.5 Engine oil:](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/17-lubrication/engine-oil/#t235-472).
> - Oil spray jet and pressure relief valve [⇒ 1.1 Assembly overview - sump/oil pump](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/17-lubrication/assembly-overview-sump-oil-pump/#t228-251).

**Removing**

- Remove noise insulation:
  Polo ⇒ General body repairs, exterior; Rep. gr. 50; Noise insulation; Assembly overview - noise insulation
- Place used oil collection and extraction unit - V.A.G 1782- under engine and drain engine oil.

> **Note**
>
> Please observe disposal instructions!

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/752f340bf1acf38b.webp)

- Remove connecting hose »cold side«.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/560544959c07a537.webp)

- Separate electrical connector -1- on charge pressure sender - G 31- / intake air temperature sensor - G 42- and remove right charge air pipe.
- Remove securing bolts -arrows- of charge air pipe and press pipe aside.
- Free off coolant hose -3-.
- Release hose clip -2-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/fc7f2f967d8f7330.webp)

- Remove securing bolt -arrow- and push coolant circulation pump 2 - V178- aside.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/b3c10ed0c235446a.webp)

- Remove securing bolts -arrows- of charge air pipe on »hot side«.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/6a6f715df88a64ae.webp)

- Disconnect electrical connector -arrow- on oil level and oil temperature sender - G266-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/eaa214d4b32966ee.webp)

- Open fasteners -arrows- and remove noise insulation -1- for sump.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/a270788cf03e91eb.webp)

- Remove connecting bolts -arrows- for sump to gearbox.
- Remove oil sump securing bolts in diagonal sequence.
- Release sump carefully from adhesive.
- Loosen sump with light blows of a rubber headed hammer if necessary.
- Remove sealant residue from cylinder block using a flat scraper.

> **Caution**
>
> Danger of soiling lubrication system and bearings.
>
> - Cover open parts of engine.

> **Warning**
>
> Wear protective goggles.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/805f42dd74835acd.webp)

- Remove sealant residues from sump and cylinder block using rotating plastic brush or similar.
- Clean sealing surfaces; they must be oil and grease free.

**Installing **

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/1ef6785305ead530.webp)

> **Note**
>
> Check the expiry date of the sealant.

- Cut off nozzle on tube at front marking (∅ of nozzle approx. 2 mm).
- Apply bead of sealant onto clean sealing surface of sump as illustrated.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/0b6340fc8d00a23c.webp)

- Thickness of sealant bead: 2…3 mm.
- Run bead along inner side of bolt holes -arrows-.

> **Caution**
>
> Danger of blocking lubrication system with excess sealant.
>
> - Do not apply sealant bead thicker than specified.

> **Note**
>
> - Take particular care when applying sealant bead in area of rear sealing flange -arrows-.
> - Oil sump must be installed within 5 minutes after applying sealant.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/a270788cf03e91eb.webp)

- Position oil sump and tighten bolts [⇒ 1.1 Assembly overview - sump/oil pump](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/17-lubrication/assembly-overview-sump-oil-pump/#t228-82).

- The oil sump must be flush with the gearbox flange at the intermediate plate.

> **Note**
>
> - When installing sump with engine removed, ensure that sump is flush with crankcase at flywheel end.
> - Let sealing compound dry for approx. 30 minutes after installing oil sump. Only then fill with engine oil.

Further assembly is basically a reverse of the dismantling sequence.

- Replenish engine oil and check oil level [⇒ 1.5.2 Checking engine oil level](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/17-lubrication/engine-oil/#t236-82).

## Tightening torques on this page

### In the steps
| Step | Torque |
| --- | --- |
| Torque wrench (5 … 50 Nm) - V.A.G 1331- | 50 Nm |
