# 3.3 Checking oil pressure and oil pressure switch – 1.6 TDI CR engine (EA189)

> VW Polo 6R (Oil filter, oil pressure switch), step by step: checking oil pressure and oil pressure switch, 1.6 TDI – 12 steps and special tool V.A.G 1342.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/17-lubrication/checking-oil-pressure-and-oil-pressure-switch/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 17 – Lubrication, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [3.2 Removing and installing oil filter housing](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/17-lubrication/removing-and-installing-oil-filter-housing/index.md)
- Next procedure: [3.4 Removing and installing oil pressure switch F1](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/17-lubrication/removing-and-installing-oil-pressure-switch-f1/index.md)

[⇒ 3.3.1 Checking oil pressure](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/17-lubrication/checking-oil-pressure-and-oil-pressure-switch/#t247-713)

[⇒ 3.3.2 Checking oil pressure switch](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/17-lubrication/checking-oil-pressure-and-oil-pressure-switch/#t248-462)

## 3.3.1 Checking oil pressure

Special tools and workshop equipment required 

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/ff03c49a040cdf08.webp)

- Oil pressure tester - V.A.G 1342-

**Procedure**

- Oil level OK.
- Engine oil temperature approx. 80°C.

- Remove oil pressure switch - F1- [⇒ 3.4 Removing and installing oil pressure switch - F1-](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/17-lubrication/removing-and-installing-oil-pressure-switch-f1/#t250-417).
- Connect oil pressure tester - V.A.G 1342- to hole for oil pressure switch - F1-.
- Screw an old oil pressure switch into hole on oil pressure tester - V.A.G 1342- to seal hole.
- Start engine.

- Oil pressure at idling speed: at least 0.6 bar.
- Increase engine speed further. At 2,000 rpm and an oil temperature of 80°C; the oil pressure should be at least 1.0 bar.

At higher engine speeds, the oil pressure must not exceed 5.0 bar. If oil pressure exceeds 5.0 bar:

- Renew oil pump.

## 3.3.2 Checking oil pressure switch

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/ffde0b823633dc0c.webp)

Special tools and workshop equipment required

- Oil pressure tester - V.A.G 1342-
- Voltage tester - V.A.G 1527 B-
- Adapter set - V.A.G 1594 C-

**Test conditions**

- Oil level OK, checking [⇒ 1.5.2 Checking engine oil level](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/17-lubrication/engine-oil/#t236-82)
- Engine oil temperature at least 80°C (radiator fan must have run once)

> **Note**
>
> Functional check and repair of the optical and acoustic oil pressure warning: ⇒ Current flow diagrams, Electrical fault finding and Fitting locations

- Remove oil pressure switch - F1- [⇒ 3.4 Removing and installing oil pressure switch - F1-](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/17-lubrication/removing-and-installing-oil-pressure-switch-f1/#t250-417).

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/09d76091640fe048.webp)

- Connect oil pressure tester - V.A.G 1342- in hole for oil pressure switch.
- Screw oil pressure switch - F1- -item 2- into hole in oil pressure tester.
- Connect brown line -1- of oil pressure tester to earth (–).
- Connect voltage tester - V.A.G 1527 B- to battery positive (+) and oil pressure switch - F1- using cables from auxiliary test set - V.A.G 1594 C-.

- LED should not light up.

> **Note**
>
> If LED lights up now, renew oil pressure switch - F1-.

- Start engine.

> **Note**
>
> Observe oil pressure tester and LED while starting, as switching point of oil pressure switch may already be exceeded when starting.
>
> - LED should light up at 0.3 to 0.6 bar.

- If LED does not light up, renew oil pressure switch - F1- [⇒ 3.4 Removing and installing oil pressure switch - F1-](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/17-lubrication/removing-and-installing-oil-pressure-switch-f1/#t250-417).
