# 3.7 Removing and installing valve stem seal – 1.6 TDI CR engine (EA189)

> Removing and installing valve stem seal, 1.6 TDI (Valve gear) on the VW Polo 6R: 40 steps. Larger diameter of valve cotters faces upwards.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-valve-stem-seal/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 15 – Cylinder head, valve gear, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [3.6 Checking hydraulic compensation elements](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/checking-hydraulic-compensation-elements/index.md)
- Next procedure: [4 Inlet and exhaust valves](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/inlet-and-exhaust-valves/index.md)

[⇒ 3.7.1 Removing and installing valve stem seals with cylinder head installed](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-valve-stem-seal/#t218-377)

[⇒ 3.7.2 Removing and installing valve stem seals with cylinder head removed](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-valve-stem-seal/#t222-82)

## 3.7.1 Removing and installing valve stem seals with cylinder head installed

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/0223b1cbab233436.webp)

Special tools and workshop equipment required

- 10 mm jointed spanner - 3220-
- Valve stem seal puller - 3364-
- Valve stem seal fitting tool - 3365-
- Removal and installation device for valve cotters - VAS 5161- with guide plate - VAS 5161/23- and knurled spacer ring - VAS 5161/23-1-

**Procedure**

- Remove all glow plugs using U/J extension and socket - 3220- [⇒ 28 – Glow plug system](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/28-glow-plug-system/).
- Remove camshafts [⇒ 3.5 Removing and installing camshaft](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-camshaft/#t210-694).
- Remove roller rocker fingers; make a note of the installation position [⇒ Item 13 (3.1 Assembly overview - valve gear)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/assembly-overview-valve-gear/#t206-245).
- Fit guide plate - VAS 5161/23- onto cylinder head.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/f15c863cd910087b.webp)

- Secure guide plate on intake manifold side with knurled screw - VAS 5161/12- and tighten hand-tight on studs using M6 collarless nuts -1-.
- Screw sealing pin - VAS 5161/10- into guide plate.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/3d326e583fe5fcd8.webp)

- Screw adapter - VAS 5161/11- hand-tight into glow plug hole of relevant cylinder.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/1eaca240cd3814f6.webp)

- Insert drift - VAS 5161/3- into guide plate and knock valve cotters loose using a plastic hammer.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/4edbba55b50c344b.webp)

- Screw engaging fork - VAS 5161/5- with snap-in device - VAS 5161/6- into guide plate.
- Slide knurled spacer ring - VAS 5161/23-1- onto assembly cartridge - VAS 5161/8-.
- Connect adapter - VAS 5161/11- to compressed air line using a commercially available connection piece, and apply constant air pressure.

- Minimum pressure: 6 bar.

- Attach pressure fork - VAS 5161/2- to snap-in device and push assembly cartridge down.
- At the same time, turn knurled screw of assembly cartridge clockwise until tips engage in valve cotters.
- Move knurled screw back and forth lightly to press apart valve cotters and capture them in the assembly piece.
- Release pressure fork.
- Take out assembly cartridge with knurled spacer ring, valve plate and valve spring.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/638835095b9e067d.webp)

- Remove valve stem oil seals using valve stem seal puller - 3364-.

**Installing**

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/58b99900b5d070e3.webp)

- Lightly oil sealing lip of valve stem oil seal and valve stem.
- Carefully push valve stem oil seal on valve stem -A-.
- Carefully press valve stem oil seal onto valve guide using valve stem seal fitting tool - 3365-.
- If necessary, use a plastic head hammer and tap lightly on fitting tool until valve stem oil seal is fitted to stop.
- Insert valve spring and valve spring plate into cylinder head.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/4f561e5aa28316c8.webp)

- If valve cotters have been removed from assembly cartridge, they need to be put into insertion device - VAS 5161/18- first.

> **Note**
>
> Larger diameter of valve cotters faces upwards.

- Press assembly cartridge onto insertion device from above and pick up valve cotters.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/d1e4f672b3645708.webp)

- Re-insert assembly cartridge - VAS 5161/8- into guide plate.
- Push pressure fork down, and pull knurled screw upwards while turning to left and right - this will insert the valve cotters.
- Release pressure fork with knurled screw still in pulled position.

Further installation is carried out in reverse order; note the following:

- Install camshafts [⇒ 3.5 Removing and installing camshaft](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-camshaft/#t210-694).
- Install glow plugs [⇒ 28 – Glow plug system](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/28-glow-plug-system/).

> **Note**
>
> - Engine is not to be rotated for approx. 30 minutes after installing camshafts. The hydraulic compensation elements must settle (otherwise valves will strike pistons).
> - After working on the valve gear, turn the engine carefully at least 2 rotations to ensure that none of the valves make contact when the starter is operated.

## 3.7.2 Removing and installing valve stem seals with cylinder head removed

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/cddd7ccb67dad8d1.webp)

Special tools and workshop equipment required

- Valve stem seal puller - 3364-
- Valve stem seal fitting tool - 3365-
- Removal and installation device for valve cotters - VAS 5161- with guide plate -VAS 5161/23- and sleeve -VAS 5161/23-1-
- Engine and gearbox support - VAS 6095-
- Cylinder head tensioning device - VAS 6419-
- Bolt M6×30 (qty. 2)

**Procedure**

- Remove camshafts [⇒ 3.5 Removing and installing camshaft](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-camshaft/#t210-694).
- Mark allocation of roller rocker fingers and hydraulic compensation elements for reinstallation.
- Remove roller rocker fingers together with hydraulic compensation elements and place down on a clean surface.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/5aa77464bff19d73.webp)

- Insert cylinder head tensioning device - VAS 6419- into engine and gearbox support - VAS 6095-.
- Clamp cylinder head in cylinder head clamping device as shown in illustration.

Operating instructions for the cylinder head tensioning device - VAS 6419- are enclosed with unit.

- Connect cylinder head tensioning device to compressed air.
- Use lever -arrow- to slide air cushion under combustion chamber from which valve stem seal is to be removed.
- Allow compressed air to flow into air cushion until it lies against valve disc.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/0ba22bad2350720a.webp)

- Place guide plate -VAS 5161/23- onto cylinder head.
- Tighten guide plate on intake manifold side by hand using knurled screw -VAS 5161/12- and 2 M6x30 bolts until it makes contact.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/efdc14da3041b1db.webp)

- Insert drift -VAS 5161/3- into guide plate and use a plastic hammer to knock loose the firmly seated valve cotters.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/1e0c07bb3f5542e6.webp)

- Screw toothed piece -VAS 5161/6- with hooking fork - VAS 5161/5- into guide plate.
- Push sleeve -VAS 5161/23-1- onto assembly cartridge - VAS 5161/8-.
- Attach pressure fork -VAS 5161/2- to toothed piece and press assembly cartridge down.
- At the same time, turn knurled screw of assembly cartridge clockwise until tips engage in valve cotters.
- Move knurled screw back and forth to press apart valve cotters and capture them in assembly cartridge.
- Release pressure fork.
- Remove assembly cartridge with knurled spacer ring.
- Remove valve spring and valve spring plate.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/638835095b9e067d.webp)

- Pull off valve stem seal using valve stem seal puller - 3364-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/58b99900b5d070e3.webp)

- Lightly oil sealing lip of valve stem oil seal and valve stem.
- Carefully push valve stem oil seal on valve stem -A-.
- Carefully press valve stem oil seal onto valve guide using valve stem seal fitting tool - 3365-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/4f561e5aa28316c8.webp)

If the valve cotters have been removed from the assembly cartridge, they must first be inserted into the valve insertion device - VAS 5161/18-.

- Larger diameter of valve cotters faces upwards.

- Insert valve spring and valve spring plate.
- Press assembly cartridge onto valve insertion device from above and pick up valve cotters.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/d1e4f672b3645708.webp)

- Insert assembly cartridge into guide plate -VAS 5161/23- again.
- Press pressure fork downwards and pull knurled screw upwards, turning it clockwise and anticlockwise. This inserts the valve cotters.
- Reduce pressure on pressure fork whilst pulling on knurled screw.
- Repeat procedure on each valve.

**Installing**

Installation is carried out in the reverse order; note the following:

- Ensure that all roller rocker fingers contact valve stem ends correctly and are clipped into relevant hydraulic compensation elements.
- Install camshafts [⇒ 3.5.2 Installing](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-camshaft/#t213-394).
