# 2.2 Removing and installing toothed belt – 1.6 TDI CR engine (EA189)

> Removing and installing toothed belt, 1.6 TDI (Toothed belt drive) on the VW Polo 6R: 40 steps, special tool 3359, tightening torques and 39 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-toothed-belt/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 15 – Cylinder head, valve gear, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [2.1 Assembly overview – toothed belt](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/assembly-overview-toothed-belt/index.md)
- Next procedure: [3.1 Assembly overview – valve gear](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/assembly-overview-valve-gear/index.md)

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/407833aa6c12d0de.webp)

Special tools and workshop equipment required

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/90ae3595d54554a1.webp)

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/3e4c430574fb318c.webp)

- 2x diesel injection pump locking pin - 3359-
- Crankshaft stop - T10050-
- Counter-hold tool - T10172-
- Angled screwdriver - T10264- for tensioning roller -A-
- Locking tool - T10265-
- Socket XZN 10 - T10385-
- Angled screwdriver - T10409- for tensioning roller -B-

Not illustrated:

- Torque wrench - V.A.G 1331-
- Torque wrench - V.A.G 1332-

> **Note**
>
> 2 versions of tensioning roller are fitted. They are not interchangeable. When performing adjusting measures, check first to see which tensioning roller is installed.

Observe different directions of rotation during tensioning

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/c63c1ec1494e7ac4.webp)

**Features tensioning roller A**

- Locking tool - T10265- required for installation.
- Check tensioning roller is seated correctly in timing belt guard.
- Tension toothed belt by turning tensioning roller eccentric »clockwise«

**Features tensioning roller B**

- Locking tool not required.
- Tensioning roller is not seated in toothed belt guard.
- Tension toothed belt by rotating tensioning roller eccentric »anticlockwise«

> **Note**
>
> Adjustment work on toothed belts must be performed only on cold engines, as the indicator position on the tensioning element varies depending on the engine temperature.

- Remove engine cover panel [⇒ 3 Engine cover panel](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/).
- With ignition switched off, disconnect battery. ⇒ Electrical system; Rep. gr. 27; Battery; Disconnecting and connecting battery
- Remove noise insulation:
  Polo ⇒ General body repairs, exterior; Rep. gr. 50; Noise insulation; Assembly overview - noise insulation
- Remove poly V-belt [⇒ 13 – Crankshaft group](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/).

Continuation for Polo [⇒ 2.2 Removing and installing toothed belt](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-toothed-belt/#t195-116) 

**Polo**

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/234a1a23092c3ba6.webp)

- Disconnect electrical connector -2- at pressure differential sender - G 505-.
- Remove pressure differential sender - G 505- from bracket -3-.
- Lay pressure differential sender - G 505- aside to rear together with lines.

Remove fuel filter with bracket.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/b53427b86ad64233.webp)

- To do this, open quick-release couplings -A- and -B- of fuel lines.
- Catch any escaping fuel.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/00ffa041dda9a2b3.webp)

- Use a finger to release locking lug of fuel pre-heater valve.
- Pull fuel pre-heater valve upwards out of coolant expansion tank guide.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/e43cc1712b4d71ba.webp)

- Unclip fuel filter from lower part of fuel filter.
- Remove fuel filter upwards.
- Separate fuel supply line and return line at engine end.
- Remove fuel filter and fuel lines together with fuel preheater valve.
- Remove lower part of fuel filter ⇒ Rep. gr. 20; Fuel filter; Removing and installing fuel filter.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/8e7229cb87b2ce28.webp)

- Unscrew bolts -arrows- for coolant expansion tank.
- Disconnect electrical connector -1- for coolant shortage indicator switch - F66-.
- Lay coolant expansion tank to one side.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/85b6e3c37da893fa.webp)

- Open clips -arrows- and remove toothed belt guard.
- Remove front right wheel housing liner.

**Continued for all vehicles**

- Remove vibration damper [⇒ 1.4 Removing and installing vibration damper](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-and-installing-vibration-damper/#t94-231).

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/520fae3b3b57ffb9.webp)

- Unscrew bolts -arrows-.
- Remove toothed belt guard downwards.

**Polo**

> **Note**
>
> Engine bracket must be removed to change tensioning roller and to remove and install toothed belt [⇒ 1.8.4 Removing and installing engine bracket, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-and-installing-engine-bracket/#t112-82).

**Continued for all vehicles**

> **Note**
>
> The engine bracket always also has to be removed in order to change the tensioning roller [⇒ 1.8 Removing and installing engine bracket](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-and-installing-engine-bracket/#t101-370).

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/826b1ca72864d27f.webp)

- Turn engine to TDC and lock crankshaft pulley in position with crankshaft stop - T10050-. Fit the crankshaft stop in the teeth from the face side of the toothed belt pulley.

- The mark -2- on the toothed pulley and the arrow -1- on the crankshaft stop - T10050- must align -arrow-. When doing this, the pin of the crankshaft stop must engage in the drilling of sealing flange.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/8a1adc0d8a08ea77.webp)

The arrow on the camshaft pulley must be at almost »12 o'clock«.

- Mark direction of rotation of toothed belt.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/6ca3421bb1f26a3e.webp)

- Loosen bolts -arrows- approx. 90° for camshaft toothed belt pulley.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/e80cc955a5029a8a.webp)

- Loosen bolts -2- approx. 90° for high-pressure pump toothed belt pulley using bit XZN 10 - T10385-.

Tensioning roller A: 

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/93d1a558df627326.webp)

- Loosen securing nut of tensioning roller -1- and turn tensioning roller eccentric using socket - T10264- counter-clockwise -arrow- until tensioning roller can be locked with locking pin - T10265-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/649ff8f5e8ee2365.webp)

- Now turn tensioning roller eccentric clockwise -arrow- onto stop and tighten securing nut -1- hand-tight.

Tensioning roller B:

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/596a8c249a9a555d.webp)

- Loosen nut -1- for belt tensioner.
- Use angled screwdriver 8mm - T10409- to rotate eccentric of tensioning roller clockwise -arrow- until tensioning roller is loosened.
- Retighten securing nut by hand.

> **Caution**
>
> Risk of irreparable damage if direction of rotation is reversed on previously used toothed belt.
>
> - Before removing toothed belt, mark direction of rotation with chalk or felt tipped pen for installation purposes.

- Remove toothed belt first from idler pulley and then from remaining toothed belt pulleys.

**Installing**

> **Note**
>
> - The toothed belt may only be adjusted on cold engines, as the indicator position on the tensioning element varies depending on the engine temperature.
> - If the tensioning roller is to be renewed, the engine bracket must always be removed along with it.
> - Removing and installing engine bracket [⇒ 1.8 Removing and installing engine bracket](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-and-installing-engine-bracket/#t101-370)

Tensioning roller A: 

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/db470a53732aa97a.webp)

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/5ba726e0fde14765.webp)

- Tensioning roller must be locked with locking tool - T10265- and secured to right stop.
- Crankshaft is locked using crankshaft stop - T10050-.

Tensioning roller B:

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/a6067efa7979770f.webp)

- Place tensioner for tensioning roller in 9 o'clock position.
- Secure tensioning roller with 2 - 4 Nm.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/31de0fb74fd4fd0b.webp)

Crankshaft is locked using crankshaft stop - T10050-.

Continuation for both tensioning rollers

> **Note**
>
> If necessary, turn camshaft hub with counterhold - T10172- and adapters - T10172/4- until camshaft can be secured in position. To do this, hand-tighten at least one securing bolt -1-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/abccc05a379bdffe.webp)

- Lock camshaft hub with locking pin - 3359-. To do this, slide locking pin through outer free elongated hole into hole in cylinder head.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/e391fc4347db352e.webp)

- Loosen bolt which had been tightened only hand-tight.

Bolts -arrows- screwed in loosely.

It should just be possible to turn camshaft toothed belt pulley without axial movement.

> **Note**
>
> If necessary, turn hub of high-pressure pump at bolt heads with screwdriver until it can be secured in position.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/0eecf4cf676fa447.webp)

Positioning hub of high-pressure pump

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/7f54340d83e6dd10.webp)

- Lock hub of high-pressure pump with locking pin - 3359-. To do this, slide locking pin into adjustment hole outside toothed belt pulley.

Loosely tightened bolts -1-.

It should just be possible to turn high-pressure pump toothed belt pulley without axial movement.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/d44d620109657ccf.webp)

- Turn camshaft toothed belt pulley -3- and toothed belt pulley of high-pressure pump -5- in their elongated holes clockwise to stop.
- Fit toothed belt in sequence described:

- **1** Crankshaft pulley
- **2** Tensioning pulley
- **3** Camshaft toothed belt pulley
- **4** Coolant pump toothed belt pulley
- **5** High-pressure pump toothed belt pulley
- **6** Idler roller

Tensioning roller A:

- Loosen tensioning roller securing nut and pull out locking tool - T10265-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/915e3533b8b09992.webp)

> **Note**
>
> Ensure that tensioning roller seats correctly in rear toothed belt guard -arrow-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/5cf99e3651ae816b.webp)

- Screw eccentric of tensioning roller clockwise carefully using angled screwdriver - T10264-. Indicator -2- must be roughly past the centre of the gap in the base plate (corrects itself during pretensioning).

Ensure that securing nut -1- does not turn as well.

- Hold tensioning roller in this position and tighten tensioning roller securing nut as follows: 20 Nm and 45° further.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/c99744625cba3644.webp)

- Apply counterhold - T10172- as shown. Press counterhold - T10172- in direction of arrow, keeping camshaft toothed belt pulley under tension.
- In this position, first tighten securing bolts -1- of camshaft pulley and of toothed belt pulley for high pressure pump by hand and then tighten to 20 Nm.

Tensioning roller B: 

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/018dd2128073b29c.webp)

- Carefully turn eccentric on tensioning roller counter clockwise using angled screwdriver - T10409-. Indicator -2- must be roughly past the centre of the gap in the base plate (corrects itself during pretensioning).

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/4937f7c86948eff5.webp)

Markings on tensioning element and tensioning roller -arrow- are now almost aligned.

Ensure that securing nut -1- does not turn as well.

- Hold tensioning roller in this position and tighten tensioning roller securing nut -1-: 20 Nm and turn 45° further.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/c99744625cba3644.webp)

- Apply counterhold - T10172- as shown. Press counterhold - T10172- in direction of arrow, keeping camshaft toothed belt pulley under tension.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/2b11d35a2844426d.webp)

- Tighten securing bolts -arrows- for camshaft pulley hand-tight at first and then to 20 Nm.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/1db22e4e76756616.webp)

- Tighten securing bolts for high-pressure pump toothed belt pulley hand-tight at first and then to 20 Nm.

Continuation for both tensioning rollers

- Remove locking pins - 3359- and crankshaft stop - T10050-.
- Turn crankshaft at least 2 rotations in engine direction of rotation and set again to TDC no. 1 cylinder.
- Fit crankshaft stop - T10050- again to crankshaft belt pulley.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/e8f474e644a63cab.webp)

- Now turn crankshaft in engine direction of rotation until pin of crankshaft stop -arrow- engages in sealing flange from rotational movement.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/6927c20df791a5b5.webp)

> **Note**
>
> During the following checking procedure, only the camshaft and crankshaft must be secured in position. It is very difficult to find the securing position of the high-pressure pump hub again. A minor deviation -arrow-, though, does not influence engine operation.

- Ensure that:

- Camshaft hub can be locked with locking pin - 3359-.
- Belt tensioner indicator is centred or maximum 5 mm to right of base plate notch.

If camshaft hub cannot be locked:

- Pull crankshaft stop - T10050- back until pin uncovers hole.
- Turn crankshaft in opposite direction of engine rotation slightly past TDC.
- Now turn crankshaft slowly in direction of engine rotation until camshaft hub can be secured in position.
- After locking, loosen securing nuts of camshaft pulley.

If pin of crankshaft stop - T10050- is standing on left next to hole: 

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/e8f474e644a63cab.webp)

- Turn crankshaft in engine direction of rotation until crankshaft stop pin engages in sealing flange whilst turning.
- Tighten securing bolts of camshaft toothed belt pulley by hand first and then tighten to 20 Nm.

If pin of crankshaft stop - T10050- is standing on right next to hole:

- Slightly turn crankshaft in opposite direction of engine rotation.
- Now turn crankshaft in engine direction of rotation until crankshaft stop pin engages in sealing flange whilst turning.
- Tighten securing bolts of camshaft toothed belt pulley by hand first and then tighten to 20 Nm.

**Continuation**

- Remove locking pin - 3359- and crankshaft stop - T10050-.
- Turn crankshaft at least 2 rotations in engine direction of rotation and set again to TDC no. 1 cylinder.
- Repeat check.
- If camshaft hub can be secured in position, tighten securing bolts as follows:

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/c99744625cba3644.webp)

- Camshaft toothed belt pulley: turn 45° further. Counterhold with counterhold - T10172- and adapters - T10172/4-.

- Install centre and lower parts of toothed belt guard.
- Install belt pulley vibration damper: specified torque 10 Nm +90° turn further.
- Install poly V-belt.
- Install upper toothed belt guard.

Further assembly is basically a reverse of the dismantling sequence. During this procedure, observe the following:

- Ensure fuel hoses are seated correctly.
- Do not interchange supply line and return line (return line blue or with blue marking, supply line white).

- Install wheel housing liner.
- Install noise insulation:
  Polo ⇒ General body repairs, exterior; Rep. gr. 50; Noise insulation; Assembly overview - noise insulation

## Tightening torques on this page

### In the steps
| Step | Torque |
| --- | --- |
| Secure tensioning roller with 2 - 4 Nm. | 4 Nm |
| Hold tensioning roller in this position and tighten tensioning roller securing nut as follows: 20 Nm and 45° further. | 20 Nm +45° |
| In this position, first tighten securing bolts -1- of camshaft pulley and of toothed belt pulley for high pressure pump by hand and then tighten to 20 Nm. | 20 Nm |
| Hold tensioning roller in this position and tighten tensioning roller securing nut -1-: 20 Nm and turn 45° further. | 20 Nm +45° |
| Tighten securing bolts -arrows- for camshaft pulley hand-tight at first and then to 20 Nm. | 20 Nm |
| Tighten securing bolts for high-pressure pump toothed belt pulley hand-tight at first and then to 20 Nm. | 20 Nm |
| Tighten securing bolts of camshaft toothed belt pulley by hand first and then tighten to 20 Nm. | 20 Nm |
| Tighten securing bolts of camshaft toothed belt pulley by hand first and then tighten to 20 Nm. | 20 Nm |
| Install belt pulley vibration damper: specified torque 10 Nm +90° turn further. | 10 Nm +90° |
