# 1.2 Removing and installing cylinder head – 1.6 TDI CR engine (EA189)

> Removing and installing cylinder head, 1.6 TDI on the VW Polo 6R: 40 steps and tightening torques. Vehicles with intake manifold flap motor V157.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-cylinder-head/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 15 – Cylinder head, valve gear, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [1.1 Assembly overview – cylinder head](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/assembly-overview-cylinder-head/index.md)
- Next procedure: [1.3 Assembly overview – cylinder head cover](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/assembly-overview-cylinder-head-cover/index.md)

[⇒ 1.2.1 Removing and installing cylinder head, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-cylinder-head/#t144-158)

## 1.2.1 Removing and installing cylinder head, Polo

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/1d8b40f1bdd6f022.webp)

Special tools and workshop equipment required

- Guide pin - 3070-
- Diesel injection pump locking pin - 3359-
- Crankshaft stop - T10050-
- Counter-hold tool - T10051-
- Puller - T10052-
- Socket XZN 10 - T10385- 

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/e9c7e421fc3657f5.webp)

- Torque wrench - V.A.G 1331-
- Torque wrench - V.A.G 1332-
- Drip tray for workshop hoist - VAS 6208-
- Tool set - T100395-

Additional special tools required for Polo 

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/c57c4ded577f7fc5.webp)

Special tools and workshop equipment required

- Support - 10-222 A-
- Adapter - 10 - 222 A /8-
- Hook - 10-222 A/10-
- Shackle - 10-222 A/12-

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/8ed164a53b3d8a5f.webp)

- Adapter - 10-222 A/18- 

**Continued for all vehicles**

> **Note**
>
> - The battery earth must be disconnected for the remaining procedure. Therefore, first check whether a coded radio is fitted. Then obtain anti-theft coding first if necessary.
> - All cable ties which are opened or cut through when cylinder head is removed must be fastened in the same position when cylinder head is installed.
> - All connectors which are separated during disassembly must be reconnected in the original position when installing.

> **Warning**
>
> - Observe the following points during all installation work, in particular in the engine compartment, due to the space limitations:
> - Route all the various lines and electrical wiring so that they are in their original positions.
> - e.g. for fuel, hydraulics, activated charcoal filter system, coolant and refrigerant, brake fluid, vacuum.
> - Ensure that there is sufficient clearance to all moving or hot components.

**Removing**

- Remove engine cover panel [⇒ 3 Engine cover panel](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/).

Polo

- Remove windscreen wiper arms: ⇒ Electrical system; Rep. gr. 92; Windscreen wiper system; Removing and installing windscreen wiper arms.

Polo

- Remove plenum chamber bulkhead ⇒ General body repairs, exterior; Rep. gr. 50; Plenum chamber bulkhead; Assembly overview - bulkhead.

**Continued for all vehicles**

- Remove noise insulation:
  Polo ⇒ General body repairs, exterior; Rep. gr. 50; Noise insulation; Assembly overview - noise insulation

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/0f13373de156427a.webp)

- Pull vacuum line -1- off vacuum pump -2-.

**Polo**

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/7a77a6a85dff1417.webp)

- Remove vacuum lines upwards from air filter -1- together with bracket.
- Pull connector off charge pressure control solenoid valve - N75- -3-.
- Unbolt charge pressure control solenoid valve - N75- with bracket at -2-.
- Place charge pressure control solenoid valve - N75- with vacuum lines on engine.
- Remove air filter housing together with air mass meter and intake hose [⇒ 7.2.2 Removing and installing air filter housing, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-air-filter-housing/#t448-678).

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/96413f12c52673b0.webp)

Pre-heater line -arrow 2- is not necessarily installed.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/46ac3547561fd0e7.webp)

- In order to ensure that vacuum hose -arrow 1- from brake servo to engine is not damaged, you must remove it ⇒ Brake systems; Rep. gr. 47; Brake servo/brake master cylinder; Assembly overview - brake servo/brake master cylinder.
- Separate connectors.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/11c2c7c19bed9e4d.webp)

- -1- Exhaust gas temperature sender 1 - G 235-
- -2- Exhaust gas temperature sender 3 - G 495-
- -3- Exhaust gas temperature sender 4 - G 648-
- -4- lambda probe - G 39-

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/23219144c13898bb.webp)

- Disconnect electrical connector -2- at pressure differential sender - G 505-.
- Unscrew bolt -3- from pressure differential sender - G 505- bracket.
- Lay pressure differential sender - G 505- aside to rear together with lines.

Remove fuel filter with bracket.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/ac32ca43b60574a8.webp)

- To do this, open quick-release couplings -A- and -B- of fuel lines.
- Catch any escaping fuel.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/5bdf0b61356652ac.webp)

- Use a finger to release locking lug of fuel pre-heater valve.
- Pull fuel pre-heater valve upwards out of coolant expansion tank guide.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/1039036cb5825db2.webp)

- Unclip fuel filter from lower part of fuel filter.
- Remove fuel filter upwards.
- Separate fuel supply line and return line at engine end.
- Remove fuel filter and fuel lines together with fuel preheater valve.
- Catch any escaping fuel.
- Remove lower part of fuel filter ⇒ Rep. gr. 20; Fuel filter; Removing and installing fuel filter.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/2e88e75803b3c629.webp)

- Filler neck: Unclip windscreen washer system reservoir -1-.
- Filler neck: Unclip windscreen washer system reservoir -2-.

**Continued for all vehicles**

- Remove cylinder head cover [⇒ 1.4 Removing and installing cylinder head cover](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-cylinder-head-cover/#t174-594).

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/e4abb66134b00188.webp)

- Unclip vacuum lines -arrow- and lay to side.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/941ed06a53d87b59.webp)

- Pull off breather line -2-.
- Lay vacuum lines to side.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/befe7139281aaf26.webp)

- Separate electrical connector -1- on oil pressure switch - F1-.
- Unscrew bolt -arrow-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/60962e329376d975.webp)

- Disconnect electrical connector -4- at coolant temperature sender - G62-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/faa4ac9624539744.webp)

- Unclip engine pre-wiring harness from retainer -arrow-.

Vehicles with intake manifold flap motor - V157-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/6c3f7025277ed167.webp)

- Disconnect connector -3- from intake manifold flap motor - V157-.

**Continued for all vehicles**

- Lay engine pre-wiring harness to one side.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/19387d7e4d4c62c2.webp)

- Pull connectors off throttle valve module - J338- -2-.
- Open clamp -3- and pull off charge air hose.
- Remove bolt from oil dipstick attachment -4-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/46376ef578eed4b6.webp)

- Unscrew bolts -2, 5- and -arrows-.
- Free electrical lines and hoses on left charge air pipe.
- Loosen hose clip -3- and remove left charge air pipe.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/784149f150cfbcce.webp)

- Unscrew bolts -arrows- and remove pulsation damper -2-.
- Carefully push charge air pipe to side as far as possible.

> **Caution**
>
> Ensure that flexible joint of connecting pipe is not bent and stretched. There is a danger of cracking.

Loosen particulate filter.

to create space for removing and installing the oil supply line with turbocharger support.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/2038c0ea69b7aeed.webp)

- Remove securing clamp -1- between particulate filter and turbocharger.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/7d9c8a98b3844248.webp)

- Unscrew bolt -1-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/bb906c609c8ec2ea.webp)

- Unscrew nuts -2-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/90c483634a72d687.webp)

- Now you can access the securing bolt on the retaining clamp -arrow- for the oil return line on the turbocharger support. Unscrew bolt -arrow-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/2f01703e44b309b5.webp)

- Remove connecting pipes -A- to exhaust gas recirculation cooler.

**Polo**

- Remove oil supply line and turbocharger support [⇒ 4 Oil circuit](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/17-lubrication/).

**Continued for all vehicles**

- Drain coolant [⇒ 1.3 Draining and adding coolant](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/draining-and-adding-coolant/#t267-554).

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/01e41919c29f46c4.webp)

- Remove coolant hoses from connections, loosen hose clips -1- and -2- for this.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/0c8aae1f1fcf06d3.webp)

- Separate connector of Hall sender - G40- -1-.
- Unscrew securing nut of toothed belt tensioning roller.

Set up support bracket - 10 - 222 A- with necessary adapters and support engine in installation position [⇒ 2.2 Supporting engine in installation position](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/supporting-engine-in-installation-position/#t72-383).

> **Note**
>
> - The assembly mounting may only be removed if the engine is supported with support bracket 10 - 222A.
> - The engine bracket must be loosened only when the assembly mounting has been removed.

- Removing engine mounting completely [⇒ 2.1.3 Removing and installing assembly mountings](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/assembly-overview-assembly-mountings/#t69-476).
- Remove engine bracket [⇒ 1.8.4 Removing and installing engine bracket, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-and-installing-engine-bracket/#t112-82).

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/239b528cdb348767.webp)

- Unscrew and remove securing bolt -arrow- of rear toothed belt guard.
- Remove toothed belt from camshaft and high-pressure pump [⇒ 2.2 Removing and installing toothed belt](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-toothed-belt/#t190-82).
- Now toothed belt tensioning roller can be removed.
- Install engine bracket again, tightening old bolts by hand [⇒ 1.8.4 Removing and installing engine bracket, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-and-installing-engine-bracket/#t112-82).
- Install assembly mountings again, tightening old bolts by hand [⇒ 1.8.4 Removing and installing engine bracket, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-and-installing-engine-bracket/#t112-82).
- Remove support bracket - 10 - 222 A-.

**Continued for all vehicles**

- Detach camshaft pulley from hub.
- Remove camshaft hub; pull off camshaft hub using puller - T10052-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/cce984023c6d615a.webp)

- Counterhold hub with counterhold - T10051- and loosen securing bolt -1- of hub.
- Loosen hub securing bolt about 2 turns.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/9bf9f99a3b508515.webp)

- Fit puller - T10052- and align it with holes in hub.
- Tighten securing bolts -1-.
- Apply tension to hub by evenly tightening puller -2- until hub separates from taper of camshaft.

> **Note**
>
> When doing this, hold puller with 30 mm spanner.

- Remove hub from taper of camshaft.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/30db6b683cd9ab94.webp)

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/a41ea86c91124a95.webp)

- Unscrew Hall sender - G40- -arrow-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/b79402d6b36f8438.webp)

- Maintain sequence when loosening cylinder head bolts.

> **Note**
>
> - A second mechanic is required to remove the cylinder head.
> - The toothed belt tensioning roller is pulled off the stud when the cylinder head is lifted out.

- First lift cylinder head on gearbox side and guide it out of toothed belt guard. Make sure that toothed belt tensioner does not fall down.

**Installing**

Install in reverse order, noting the following: 

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/23aaaaa20b570d76.webp)

> **Note**
>
> - Do not use sandpaper, grinding wheels, abrasive or scour pads or any other sanding or abrasive media.
> - Sealing surface (see photo) must not project.
> - Discolouration (dark spots, see photo) need not be removed.
> - When removing the sealant residue, make sure no loose particles get into the open channels of the engine.
> - Ensure that all adjacent workspaces are clean, and that none of the above mentioned sanding or abrasive media are used.
> - Using unauthorised sanding or abrasive media may lead to secondary damage such as, for example, damage to the turbocharger or the conrod bearings.

- Only remove sealant residue from cylinder head and cylinder block using scraper - VAS 852 005- or a commercially available ceramic glass scraper.

- The sealing surfaces must not be damaged.
- There must be no oil or coolant in the bolt pockets.
- Do not remove new cylinder head gasket from packaging until it is ready to be fitted.
- If a new cylinder head is installed, contact surfaces between roller rocker fingers and running surface of cam must be oiled.
- Handle the cylinder head gasket very carefully to prevent damage to the silicone coating or the indented area of the gasket.
- Turn the crankshaft carefully at least 2 rotations to ensure that none of the valves make contact when the starter is operated.
- When the cylinder head or cylinder head gasket is renewed, the entire coolant and the engine oil must be changed.

- Remove any loose remains using a lint-free cloth.
- Before fitting cylinder head, remove crankshaft stop - T10050-, and turn crankshaft in opposite direction of engine rotation until all pistons are nearly uniformly below TDC.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/672d723d5e363d79.webp)

- Note cylinder head gasket identification:

- **1** Part number
- **2** Holes
- **3** Ignore

- Cylinder head gasket must lie with identification facing upwards.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/1e028e4930119804.webp)

- To centre, screw guide pins -3070/9- into outer threaded holes on intake side.

> **Note**
>
> - Polo: Belt tensioner must be pushed onto stud after fitting cylinder head.
> - Polo: Support engine again.
> - If the cylinder head gasket or cylinder head have been replaced, select the new cylinder head gasket according to the number of holes on the old cylinder head gasket.
> - If parts of the crankshaft assembly have been renewed, the new cylinder head gasket must be selected by measuring the piston projection at “TDC” [⇒ 4.1 Assembly overview - pistons and conrods](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/assembly-overview-pistons-and-conrods/#t133-197).

- Fit cylinder head.
- Insert 8 cylinder head bolts and screw in by hand until contact is made.
- Unscrew guide pins -3070/9- through bolt holes in cylinder head and screw remaining cylinder head bolts by hand until contact is made.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/48e1379eaa67d0ec.webp)

- Tighten cylinder head in 4 stages in sequence shown as follows:

- **1** Tighten initially with torque wrench:

Stage I = 35 Nm

Step II = 60 Nm

- **2** Turn further with rigid spanner:

Stage III = turn 90° further.

Stage IV = turn 90° further.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/79fd745c00af2a9a.webp)

- Re-fit Hall sender - G40- -arrow-.

**Polo**

- Secure rear toothed belt guard -arrow- on cylinder head after supporting it.

**Continued for all vehicles**

- Install hub and camshaft pulley.
- Lock camshaft and high-pressure pump with diesel injection pump locking pin - 3359-

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/e8f474e644a63cab.webp)

- Now rotate crankshaft in direction of rotation to TDC and lock crankshaft using crankshaft stop - T10050-.

Continue installation in reverse order of removal. During this procedure, observe the following:

**Polo**

Support engine again [⇒ 1.8.4 Removing and installing engine bracket, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-and-installing-engine-bracket/#t112-82).

- Re-install toothed belt [⇒ 2.2 Removing and installing toothed belt](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-toothed-belt/#t190-82).
- Install engine bracket [⇒ 1.8.4 Removing and installing engine bracket, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-and-installing-engine-bracket/#t112-82).

**Continued for all vehicles**

- Install cylinder head cover [⇒ 1.4 Removing and installing cylinder head cover](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-cylinder-head-cover/#t174-594).
- Install oil supply line and turbocharger support [⇒ 3 Oil filter, oil pressure switch](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/17-lubrication/).
- Install poly V-belt [⇒ 13 – Crankshaft group](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/).
- Add coolant [⇒ 1.3.2 Filling with coolant](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/draining-and-adding-coolant/#t270-82).
- Top up engine oil [⇒ 1.5.2 Checking engine oil level](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/17-lubrication/engine-oil/#t236-82).

After any work on the fuel system

Connect a diagnostic tester.

Perform the function “Filling/bleeding high pressure pump/fuel system” in “Guided functions” [⇒ 1.3 Filling/bleeding fuel system](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/filling-bleeding-fuel-system/#t392-82).

- Carry out road test and read all event memories.

## Tightening torques on this page

### 1.2.1 Removing and installing cylinder head, Polo [To the steps](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-cylinder-head/#1-2-1-removing-and-installing-cylinder-head-polo-golf-golf-p)
| Step | Torque |
| --- | --- |
| Stage I = 35 Nm | 35 Nm |
| Step II = 60 Nm | 60 Nm |
