# 3.5 Removing and installing camshaft – 1.6 TDI CR engine (EA189)

> Removing and installing camshaft, 1.6 TDI (Valve gear) on the VW Polo 6R: 40 steps, special tools 3359 and T10051, tightening torques and 20 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-camshaft/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 15 – Cylinder head, valve gear, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [3.4 Removing and installing camshaft oil seal](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-camshaft-oil-seal/index.md)
- Next procedure: [3.6 Checking hydraulic compensation elements](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/checking-hydraulic-compensation-elements/index.md)

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/2fb25883f2dcc8dd.webp)

Special tools and workshop equipment required

- Diesel injection pump locking pin - 3359-
- Counter-hold tool - T10051-
- Puller - T10052-
- Camshaft fitting tool - T40094-
- Camshaft clamping tool - T40095-
- Camshaft fitting tool - T40096-

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/80da8ddb7bc2c8c6.webp)

- Torque wrench - V.A.G 1331/- 

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/e26e6702032ea748.webp)

- Torque wrench - V.A.G 1332/-
- Sealant as per ⇒ Electronic Parts Catalogue (ETKA)

## 3.5.1 Removing

- Remove engine cover panel [⇒ 3 Engine cover panel](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/).
- Remove fuel filter ⇒ Rep. gr. 20; Fuel filter; Removing and installing fuel filter.
- Removed toothed belt from camshaft and high-pressure pump [⇒ 2.2 Removing and installing toothed belt](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-toothed-belt/#t190-82).
- Remove cylinder head cover [⇒ 1.4 Removing and installing cylinder head cover](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-cylinder-head-cover/#t174-594).

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/ca9a28d9227c0bfc.webp)

- Unscrew securing bolts -1- of camshaft sprocket.
- Detach camshaft pulley from hub.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/e0e28723aab768cd.webp)

- Counterhold hub with counterhold - T10051- and loosen securing bolt -1- of hub.
- Loosen hub securing bolt about 2 turns.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/fa2e989377023673.webp)

- Fit puller - T10052- and align it with holes in hub.
- Tighten securing bolts -1-.
- Apply tension to hub by evenly tightening puller -2- until hub separates from taper of camshaft.

> **Note**
>
> When doing this, hold puller with 30 mm spanner.

- Remove hub from taper of camshaft.
- Remove vacuum pump [⇒ 1.5 Removing and installing vacuum pump](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-vacuum-pump/#t182-373).

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/7a14927cd5fe2b0f.webp)

- Remove securing bolts of retaining frame in sequence -24…1-.
- Release retaining frame carefully from adhesive.
- Mark camshafts for re-installation and remove.

## 3.5.2 Installing

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/ae2e00124c9fa921.webp)

> **Note**
>
> - Gradual discontinuation of two-piece camshaft sprocket
> - Note the differences in the »Installing« procedure.

Remove one-piece -arrow- camshaft sprocket

> **Caution**
>
> The camshafts may be installed only with the camshaft fitting tool - T40094- as described below. Otherwise the axial bearings in the retaining frame will be destroyed and the cylinder head must be replaced.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/dbda94fbcb5301c8.webp)

- Remove sealant residue from cylinder block and retaining frame using, for example, a plastic rotary brush.

> **Caution**
>
> Danger of soiling lubrication system and bearings.
>
> - Cover open parts of engine.

- Clean sealing surfaces. They must be free of oil and grease.
- Lubricate running surfaces of camshafts.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/4728b0ca12456fa1.webp)

Prepare camshaft fitting tool - T40094- as follows:

- Bolt supports -T40094/9- and -T40094/10- (with -T40094/11- ) to base plate as shown in illustration. Remove any bolted-on supports here if necessary.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/3d3c2b84c79bb6b1.webp)

- Place support -T40094/1- in position -F- and support - T40094/2- in position -A-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/1c2b85483a52da25.webp)

- Insert inlet camshaft into supports -T40094/1- and - T40094/2-.
- Turn inlet camshaft so that it can be locked in “TDC” position with locking ruler -arrow 1-.

- The indentation -arrow 2- for the cylinder head bolt must face outwards.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/483429c2566c911c.webp)

- Insert exhaust camshaft into supports -T40094/9- and - T40094/10-.
- Lock exhaust camshaft with cover -T40094/11-.

- The lug -1- of the cover must engage in the slot -2- in the camshaft.

Vehicles with two-piece camshaft sprocket:

- Place clamping tool -T40096/1- on teeth of exhaust camshaft in such a way that the two arms of the tool engage on the two halves of the gear (one in each half, as shown in illustration).

- The wider arm must engage in the wider gear half.

- Tighten clamping tool using knurled wheel so that faces of gear teeth are in alignment.

**Continued for all vehicles**

- Slide inlet camshaft towards exhaust camshaft until teeth engage.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/252fef6f3937118a.webp)

- Place retaining frame -1- on camshafts.

- All camshaft bearings must be seated on the camshafts.

- Fit camshaft fitting tool - T40095- and fix camshafts in position in retaining frame as shown in the illustration.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/dc9b3bd1ca968809.webp)

- Remove -T40094/11- cover.

> **Note**
>
> - Check the expiry date of the sealant.
> - Seal parting surface between retaining frame and cylinder head using silicone adhesive sealant - D 176 501 A1-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/1ef6785305ead530.webp)

- Cut off nozzle on tube at front marking (∅ of nozzle approx. 2 mm).
- Apply beads of sealant onto clean sealing surfaces of cylinder head as illustrated.

- Thickness of sealant beads: 2…3 mm.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/5aa42a47f6652be7.webp)

- Install new cap flush on cylinder head.
- Remove camshafts together with retaining frame and clamping tool - T40095- from camshaft fitting tool - T40094-.
- Carefully insert camshafts and retaining frame into cylinder head.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/861f8039e1d8ad0e.webp)

- Hand-tighten retaining frame securing bolts in sequence -1 … 24- initially.

- The retaining frame should make contact with the cylinder head over the complete surface.

- Tighten retaining frame bolts to final torque in the sequence -1 … 24-. Specified torque: 10 Nm
- Remove camshaft fitting tool - T40095- and clamping tool - T40096/1-.
- Renew camshaft seal [⇒ 3.4 Removing and installing camshaft oil seal](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-camshaft-oil-seal/#t208-99).

Perform further installation in reverse order, paying attention to the following:

> **Note**
>
> - After installing camshafts wait for approx. 30 minutes before starting engine. The hydraulic compensation elements must settle (otherwise valves will strike pistons).
> - After working on valve gear, carefully crank engine at least 2 revolutions by hand to ensure that no valves make contact on starting.

- Place hub onto camshaft.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/866946ab0425ff09.webp)

- Tighten hub securing bolt -1- to 100 Nm. To do this, use the counterhold - T10051-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/ba8563a8a85785d0.webp)

- Push camshaft sprocket onto hub.

> **Note**
>
> The toothed segment -arrow- of the camshaft belt pulley must be on top.

- Hand tighten securing bolts -1- at camshaft sprocket so that there is no play.
- Lock hub with locking pin - 3359-.
- Install toothed belt and adjust valve timing [⇒ 2.2 Removing and installing toothed belt](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-toothed-belt/#t190-82).
- Install vacuum pump [⇒ 1.5 Removing and installing vacuum pump](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-vacuum-pump/#t182-373).
- Install cylinder head cover [⇒ 1.4 Removing and installing cylinder head cover](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-cylinder-head-cover/#t174-594).
- Install fuel filter ⇒ Rep. gr. 20; Fuel filter; Removing and installing fuel filter.

## Tightening torques on this page

### 3.5.2 Installing [To the steps](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-camshaft/#3-5-2-installing)
| Step | Torque |
| --- | --- |
| Tighten retaining frame bolts to final torque in the sequence -1 … 24-. Specified torque: 10 Nm | 10 Nm |
| Tighten hub securing bolt -1- to 100 Nm. To do this, use the counterhold - T10051-. | 100 Nm |
