# 3.4 Removing and installing camshaft oil seal – 1.6 TDI CR engine (EA189)

> Removing and installing camshaft oil seal, 1.6 TDI (Valve gear) on the VW Polo 6R: 18 steps, special tools 3240 and 10203 and 9 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-camshaft-oil-seal/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 15 – Cylinder head, valve gear, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [3.3 Measuring radial play of camshaft](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/measuring-radial-play-of-camshaft/index.md)
- Next procedure: [3.5 Removing and installing camshaft](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-camshaft/index.md)

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/a1b759b85fe4865c.webp)

> **Note**
>
> - A modified oil seal is gradually being introduced.
> - The “old version” of the oil seal -item A- forms a continuous surface between the camshaft and the cylinder head.
> - The “new version” of the oil seal -item B- forms a stepped surface between the camshaft and the cylinder head.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/c4a925bb5dff4903.webp)

Special tools and workshop  equipment required

- Fitting tool - V.A.G 10-203-
- Seal puller - 3240-
- Torque wrench - V.A.G 1331/-
- Torque wrench - V.A.G 1332/-
- Use bolt M12 x 1.5 x 75 -10203-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/711374c473bcd355.webp)

Puller - T10443- for “new version” of oil seal

**Removing**

- Take toothed belt off camshaft and high-pressure pump [⇒ 2.2 Removing and installing toothed belt](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-toothed-belt/#t190-82).
- Remove camshaft pulley and hub [⇒ 3.5 Removing and installing camshaft](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-camshaft/#t210-694).

“Old version” of oil seal:

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/69d3a4e1358ecdc5.webp)

- Insert thrust piece -3240/1- into camshaft.
- Unscrew inner part of oil seal extractor - 3240- 2 turns (approx. 3 mm) from the outer part and lock in position with the knurled screw.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/7df1beae1bafd693.webp)

- Lubricate threaded head of oil seal extractor, place it in position and, exerting firm pressure, screw it into oil seal as far as possible.
- Loosen knurled screw and turn inner part against camshaft until oil seal is pulled out.
- Clamp oil seal extractor on flats in a vice and remove oil seal using pliers.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/32b58cb8da35dce8.webp)

“New version” of oil seal:

> **Caution**
>
> - If unscrewed too far, the internal thrust plate of the puller
>   - T10443- detaches from the thrust screw. In this case, the pressure plate must be pressed back on to the thrust bolt.

- Carefully unscrew grub screw -arrow- of puller -T10443- until a slight resistance is felt.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/9ac7e1e1a083ffd6.webp)

- Position puller - T10443- such that it is straight, as shown in illustration, and lock it in place by screwing in grub screw -A-.
- Screw in thrust bolt -B- until oil seal is extracted.

**Installing**

- Clean contact surface and sealing surface.

> **Note**
>
> Do not be additionally oil or grease the oil seal sealing lip.

- Remove oil residue from camshaft journal using a clean cloth.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/a104bb15d056f86e.webp)

- Fit guide sleeve -10-203- onto camshaft as shown in illustration.
- Carefully slide oil seal -1- over guide sleeve onto camshaft.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/5fdb947a143a781f.webp)

- Press seal in onto stop using thrust piece from fitting tool 10-203 and M12x1.5x75 bolt.
- Install camshaft pulley and hub [⇒ 3.5 Removing and installing camshaft](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-camshaft/#t210-694).
- Install toothed belt and adjust valve timing [⇒ 2.2 Removing and installing toothed belt](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-toothed-belt/#t190-82).
